NAVIGATION SYSTEM (for HDD), Diagnostic DTC:B15B0

DESCRIPTION

This DTC is stored when a malfunction occurs in the navigation computer sub-assembly, multi-display or display module board.

INSPECTION PROCEDURE

PROCEDURE

1. Click here

   CLEAR DTC

   
   

   1. Clear the DTC (Click here).

   
   
   • NEXTClick here
2. Click here

   CHECK FOREIGN OBJECT

   
   

   1. Check the area around the center instrument cluster finish panel assembly for obstacles or protrusions which may interrupt opening/closing of the multi-display, and also check for foreign objects stuck in moving parts. If any foreign objects are present, remove them.

   
   
   • NEXTClick here
3. Click here

   CHECK DTC

   Tip:
   

   • The trouble area cannot be determined by checking DTCs with the intelligent tester. It is necessary to display the "System Check Mode" screen to determine the trouble area.

   • If the picture circuit is faulty, the multi-display or the navigation computer sub-assembly stores the DTC.

   • If the multi-display open/close function is malfunctioning, the display module board stores the DTC.

   • If the multi-display does not open when the power switch is turned on (ACC), manually open the multi-display and display the "System Check Mode" screen.

   
   
   1. 

      Display the "System Check Mode" screen (Click here).

   2. Check result on the "System Check Mode" screen.

      Result

      Result Proceed to The trouble area cannot be determined using the "System Check Mode" screen due to a multi-display malfunction. A DTC "B15B0" is output from "EMV-M". B DTC "B15B0" is output from "DISP". C The trouble area cannot be determined using the "System Check Mode" screen because the multi-display does not open when the power switch is turned on (ACC). D DTC "B15B0" is output from "MOTOR-C". D No DTCs are output. E

      Table 1. Text in Illustration

      *a

      Example

   
   
   • AClick here
   • BClick here
   • CClick here
   • DClick here
   • EClick here
4. Click here

   REPLACE MULTI-DISPLAY

   
   

   1. Replace the multi-display (Click here).

   2. Clear the DTCs (Click here).

   3. Recheck for DTCs and check if the same DTCs are output again.

      OK
      No DTCs are output.

   
   
   • OKClick here
   • NGClick here
5. Click here

   END

6. Click here

   REPLACE NAVIGATION COMPUTER SUB-ASSEMBLYClick here

7. Click here

   REPLACE MULTI-DISPLAYClick here

8. Click here

   USE SIMULATION METHOD TO CHECKClick here

9. Click here

   REPLACE NAVIGATION COMPUTER SUB-ASSEMBLYClick here

10. Click here

    CHECK CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (DRIVING PART USED FOR DRIVEN PART OF MULTI-DISPLAY)

    
    

    1. Check that there is no damage on the driving parts that drive the multi-display and that no foreign objects are caught (Click here).

       Result
       Result Proceed to Damage on the driving parts. A Foreign objects are caught between the driving parts. B No damage on the driving parts and no foreign objects are caught between the driving parts. C

    
    
    • AClick here
    • BClick here
    • CClick here
11. Click here

    REPLACE DAMAGED DRIVING PART

    
    

    1. Replace damaged driving parts (Click here).

    2. Clear the DTCs (Click here).

    3. Recheck for DTCs and check if the same DTCs are output again.

       OK
       No DTCs are output.

    
    
    • OKClick here
    • NGClick here
12. Click here

    END

13. Click here

    REMOVE FOREIGN OBJECT

    
    

    1. Remove foreign objects caught between the driving parts.

    2. Clear the DTCs (Click here).

    3. Recheck for DTCs and check if the same DTCs are output again.

       OK
       No DTCs are output.

    
    
    • OKClick here
    • NGClick here
14. Click here

    END

15. Click here

    REPLACE MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY

    
    

    1. Replace the multi-display controller sub-assembly (Click here).

    2. Clear the DTCs (Click here).

    3. Recheck for DTCs and check if the same DTCs are output again.

       OK
       No DTCs are output.

    
    
    • OKClick here
    • NGClick here
16. Click here

    END

17. Click here

    REPLACE SENSOR WIRE

    
    

    1. Replace the sensor wire (Click here).

    2. Clear the DTCs (Click here).

    3. Recheck for DTCs and check if the same DTCs are output again.

       OK
       No DTCs are output.

    
    
    • OKClick here
    • NGClick here
18. Click here

    END

19. Click here

    REPLACE DISPLAY MODULE BOARDClick here