NAVIGATION SYSTEM (for HDD), Diagnostic DTC:B156F, B1560

DTC Code DTC Name
B156F No Response from Motor Control
B1560 Motor Control Disconnected

DESCRIPTION

The navigation computer sub-assembly and display module board are connected by the AVC-LAN communication line.

When an AVC-LAN communication error occurs between the navigation computer sub-assembly and display module board, these DTCs will be stored.

DTC No. DTC Detection Condition Trouble Area
B156F No response to the diagnostic memory request from the master unit.

  • Display module board power source circuit

  • AVC-LAN circuit between navigation computer sub-assembly and display module board

  • Display module board

  • Navigation computer sub-assembly
B1560*1 A device that is listed in the AVC-LAN connected device record of the master unit is missing.

Tech Tips


  • *1: Even if no fault is present, this DTC may be stored depending on the auxiliary battery condition or hybrid system start voltage.

  • The navigation computer sub-assembly is the master unit.

WIRING DIAGRAM

A003X1DE09

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Check for optional components


      1. Check that optional components (including associated wiring) which generate radio waves are not installed.

        Result
        Result Proceed to
        Optional components (including associated wiring) are installed. A
        Optional components (including associated wiring) are not installed. B

        Tech Tips


        • Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

        • These DTCs may be stored when an AVC-LAN communication error occurs due to electrical noise.


    B

    CHECK DTC Click here

    A

  2. REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Remove optional components (including associated wiring).

      Note

      Do not remove optional components or associated wiring without the permission of the customer.


    NEXT

  3. CHECK DTC


    1. Clear the DTCs Click here.

    2. Recheck for DTCs and check if the same DTCs are output again.

      OK
      No DTCs are output.

    NG

    CHECK HARNESS AND CONNECTOR (DISPLAY MODULE BOARD POWER SOURCE) Click here

    OK

    END

  4. CHECK HARNESS AND CONNECTOR (DISPLAY MODULE BOARD POWER SOURCE)


    1. Disconnect the H21 display module board connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H21-3 (SGND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      H21-1 (+B2) - H21-3 (SGND) Power switch off 11 to 14 V
      H21-2 (ACC2) - H21-3 (SGND) Power switch on (ACC) 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR


    1. Disconnect the H21 display module board connector.

    2. Disconnect the H60 navigation computer sub-assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H21-9 (TX4+) - H60-13 (TX2+) Always Below 1 Ω
      H21-10 (TX4-) - H60-14 (TX2-) Always Below 1 Ω
      H21-9 (TX4+) - Body ground Always 10 kΩ or higher
      H21-10 (TX4-) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. REPLACE DISPLAY MODULE BOARD


    1. Replace the display module board Click here.

    2. Clear the DTCs Click here.

    3. Recheck for DTCs and check if the same DTCs are output again.

      OK
      No DTCs are output.

    NG

    REPLACE NAVIGATION COMPUTER SUB-ASSEMBLY Click here

    OK

    END