NAVIGATION SYSTEM (for DVD) Microphone Circuit between Microphone and Navigation ECU

DESCRIPTION

• The display and navigation module display and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

• Using this circuit, the display and navigation module display sends power to the map light assembly (telephone microphone assembly), and the map light assembly sends microphone signals to the display and navigation module display.

WIRING DIAGRAM

INSPECTION PROCEDURE

PROCEDURE

1. CHECK HARNESS AND CONNECTOR

   
   

   1. Disconnect the H60 display and navigation module display connector.

   2. Disconnect the T6 map light assembly connector.

   3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition H60-20 (SNS2) - T6-11 (SNS2) Always Below 1 Ω H60-4 (MACC) - T6-14 (MACC) Always Below 1 Ω H60-5 (MIN+) - T6-13 (MCO+) Always Below 1 Ω H60-6 (MIN-) - T6-12 (MCO-) Always Below 1 Ω H60-20 (SNS2) - Body ground Always 10 kΩ or higher H60-4 (MACC) - Body ground Always 10 kΩ or higher H60-5 (MIN+) - Body ground Always 10 kΩ or higher H60-6 (MIN-) - Body ground Always 10 kΩ or higher H60-7 (SGND) - Body ground Always 10 kΩ or higher

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

2. INSPECT DISPLAY AND NAVIGATION MODULE DISPLAY

   
   

   1. Reconnect the H60 display and navigation module display connector.

   2. Reconnect the T6 map light assembly connector.

   3. 

      Text in Illustration

      *a	Component with harness connected (Display and Navigation Module Display)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition H60-4 (MACC) - Body ground Power switch on (ACC) 4 to 6 V

   4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition H60-7 (SGND) - Body ground Always Below 1 Ω H60-6 (MIN-) - Body ground Always Below 1 Ω

   
   

   NG

   REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY Click here

   OK

3. INSPECT MAP LIGHT ASSEMBLY

   
   

   1. Disconnect the T6 map light assembly connector.

   2. 

      Text in Illustration

      *a	Component without harness connected (Map Light Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition T6-11 (SNS2) - T6-12 (MCO-) Always Below 1 Ω

   
   

   NG

   REPLACE TELEPHONE MICROPHONE ASSEMBLY Click here

   OK

4. INSPECT MAP LIGHT ASSEMBLY

   
   

   1. Reconnect the H60 display and navigation module display connector.

   2. 

      Text in Illustration

      *a	Component with harness connected (Map Light Assembly)

      Reconnect the T6 map light assembly connector.

   3. Turn the power switch on (ACC).

   4. Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the T6 map light assembly connector.

   5. Check the waveform of the telephone microphone assembly using the oscilloscope.

      Result
      Result Proceed to A waveform synchronized with the voice input to the map light assembly is output. A A waveform synchronized with the voice input to the map light assembly is not output. B

   
   

   B

   REPLACE TELEPHONE MICROPHONE ASSEMBLY Click here

   A

   PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

5. REPLACE TELEPHONE MICROPHONE ASSEMBLY

   
   

   1. Replace the telephone microphone assembly Click here.

   2. Check if the same malfunction recurs.

      Result
      Result Proceed to Malfunction does not recur (returns to normal) A Malfunction recurs B

   
   

   B

   REPLACE MAP LIGHT ASSEMBLY Click here

   A

   END