Tech Tips
Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
Inspect the fuses and relays related to this system before inspecting the suspected areas below.
| Symptom | Suspected Area | See page |
|---|---|---|
| The multi-display does not open when the power switch is turned on (ACC). | Proceed to "Multi-display Operation Check" in Operation Check | |
| Damage on the driving parts that drive the multi-display or foreign objects are caught. | ||
| Multi-display controller sub-assembly | ||
| Sensor wire | ||
| Display module board | ||
| The multi-display does not close when the power switch is turned off. | Proceed to "Multi-display Operation Check" in Operation Check | |
| Damage on the driving parts that drive the multi-display or foreign objects are caught. | ||
| Multi-display Controller Sub-assembly | ||
| Sensor wire | ||
| Display module board | ||
| Noise occurs when the multi-display opens, closes or tilts. | Damage on the driving parts that drive the multi-display or foreign objects are caught. | |
| Multi-display controller sub-assembly | ||
| When the power switch is turned on (ACC), the multi-display closes while opening. | Damage on the driving parts that drive the multi-display or foreign objects are caught. | |
| Multi-display controller sub-assembly | ||
| Sensor wire | ||
| Display module board | ||
| When the power switch is turned on (ACC), the multi-display stops while opening. | Damage on the driving parts that drive the multi-display or foreign objects are caught. | |
| Multi-display controller sub-assembly | ||
| Sensor wire | ||
| Display module board | ||
| The multi-display cannot be operated using the multi-display switch. | Proceed to "Multi-display Operation Check" in Operation Check | |
| Proceed to "Multi-display Switch Circuit" | ||
| Damage on the driving parts that drive the multi-display or foreign objects are caught. | ||
| Multi-display controller sub-assembly | ||
| Sensor wire | ||
| Display module board | ||
| The multi-display switch does not illuminate even when the light control switch is turned to the tail or head position. | Proceed to "Illumination Circuit" | |
| Black screen (No image appears on navigation/audio screen.) | Proceed to "Black Screen" | |
| Proceed to "Display Signal Circuit between Navigation ECU and Parking Assist ECU" | ||
| Proceed to "Display Signal Circuit between Parking Assist ECU and Multi-display" | ||
| Proceed to "Visual Mute Signal Circuit between Navigation ECU and Multi-display" | ||
| Hard disk drive | ||
| Navigation computer sub-assembly | ||
| A message is displayed to inform the driver that the program cannot be read, and the system cannot be operated using the remote touch. | Hard disk drive | |
| Navigation computer sub-assembly | ||
| A white or blue screen remains displayed after the power switch is turned on (ACC). (Even though the navigation system is operated, the screen does not change or navigation sound cannot be heard.) | Hard disk drive | |
| Navigation computer sub-assembly | ||
| Multi-display | ||
| A white or blue screen remains displayed after the power switch is turned on (ACC). (When the navigation system is operated the current position screen or a navigation screen such as MENU is displayed or navigation sound is heard.) | Navigation computer sub-assembly | |
| The multi-display does not dim even when the light control switch is turned to the tail or head position. | Confirm that the tail cancel is off. | - |
| Proceed to "Display does not Dim when Light Control Switch is Turned ON" | ||
| Display module board | ||
| Multi-display | ||
| Navigation computer sub-assembly | ||
| Power does not turn off. (Screen remains on.) | Proceed to "Navigation ECU Power Source Circuit" | |
| Navigation computer sub-assembly | ||
| Multi-display | ||
| Display module board | ||
| Noise occurs when screens switch. | Proceed to "Visual Mute Signal Circuit between Navigation ECU and Multi-display" | |
| Navigation computer sub-assembly | ||
| Multi-display | ||
| Screen is distorted. | Proceed to "Navigation ECU Power Source Circuit" | |
| Navigation computer sub-assembly | ||
| Multi-display | ||
| Screen flicker or color distortion | Proceed to "Screen Flicker or Color Distortion" | |
| Proceed to "Display Signal Circuit between Navigation ECU and Parking Assist ECU" | ||
| Proceed to "Display Signal Circuit between Parking Assist ECU and Multi-display" | ||
| Proceed to "Visual Mute Signal Circuit between Navigation ECU and Multi-display" | ||
| Navigation computer sub-assembly | ||
| DVD image cannot be displayed on front screen. (Parking brake is on.)*1 | Proceed to "DVD Image Signal Circuit between Radio Receiver and Navigation ECU" | |
| Proceed to "DVD Image Signal Circuit between Navigation ECU and Multi-display" | ||
| Proceed to "Parking Brake Switch Circuit" | ||
| Radio receiver assembly | ||
| Navigation computer sub-assembly | ||
| Multi-display | ||
| Navigation function switches can be operated while vehicle is being driven. | Navigation computer sub-assembly |
| Symptom | Suspected Area | See page |
|---|---|---|
| GPS mark is not displayed. | Proceed to "GPS Mark is not Displayed" | |
| Navigation antenna assembly | ||
| Navigation computer sub-assembly | ||
| Vehicle position mark deviates. | Proceed to "Vehicle Position Mark Deviates Greatly" | |
| Navigation antenna assembly | ||
| Navigation computer sub-assembly | ||
| Cursor or map rotates when vehicle is stopped. | Proceed to "Cursor or Map Rotates when Vehicle Stopped" | |
| Navigation computer sub-assembly | ||
| Vehicle position mark moves in the opposite direction to the vehicle. | Check if the GPS mark is displayed on the map screen. | - |
| Proceed to "Cursor or Map Rotates when Vehicle Stopped" | ||
| Navigation computer sub-assembly | ||
| Vehicle position mark is not updated. | Check if the GPS mark is displayed on the map screen. | - |
| Navigation computer sub-assembly | ||
| Voice guidance does not function. | Proceed to "Voice Guidance does not Function" | |
| Proceed to "Speaker Circuit" | ||
| Navigation computer sub-assembly | ||
| Radio receiver assembly | ||
| Stereo component amplifier assembly | ||
| Map display is incomplete. | Hard disk drive | |
| Navigation computer sub-assembly | ||
| Route cannot be calculated. | Proceed to "Route cannot be Calculated" | |
| Navigation computer sub-assembly | ||
| Screen does not change to night screen even when tail switch is turned on. | Proceed to "Display does not Dim when Light Control Switch is Turned ON" | |
| Navigation computer sub-assembly | ||
| Navigation ECU cannot record memory point registration or each item setting. | Hard disk drive | |
| Navigation computer sub-assembly | ||
| A message indicating to wait for a while because of low temperature is displayed. | Start the hybrid system and increase cabin temperature (near navigation ECU) | - |
| Proceed to "Check Hard Disk Drive" in Operation Check | ||
| Navigation computer sub-assembly | ||
| A message is displayed because map data cannot be read, and current position screen is not displayed. | If message appears only when driving on rough roads, check if message disappears when vehicle is stopped. | - |
| Hard disk drive | ||
| Navigation computer sub-assembly | ||
| Map screen turns white or blue. (GPS receiving status is displayed normally, and switches and own vehicle position mark are also displayed normally.) | Change map scale to smallest (a scale that shows a large area) | - |
| Hard disk drive | ||
| Navigation computer sub-assembly | ||
| Voice menu screen is not displayed. | Proceed to "Panel Switches do not Function" | |
| Proceed to "Steering Pad Switch Circuit" | ||
| Navigation computer sub-assembly | ||
| Voice recognition is difficult. | Proceed to "Voice Recognition Difficulty" | |
| Proceed to "Microphone Circuit between Microphone and Navigation ECU" | ||
| Navigation computer sub-assembly | ||
| Voice is not recognized. | Proceed to "Panel Switches do not Function" | |
| Proceed to "Steering Pad Switch Circuit" | ||
| Proceed to "Voice is not Recognized" | ||
| Proceed to "Microphone Circuit between Microphone and Navigation ECU" | ||
| Navigation computer sub-assembly | ||
| Reverse signal does not change in vehicle signal check mode. | Check shift indicator display on combination meter. | - |
| Navigation computer sub-assembly | ||
| Parking brake signal does not change in vehicle signal check mode. | Proceed to "Parking Brake Signal Circuit" | |
| Navigation computer sub-assembly | ||
| "MIC" is not displayed on system check mode screen. | Proceed to "Microphone Circuit between Microphone and Navigation ECU" | |
| Navigation computer sub-assembly | ||
| "AUX" is not displayed on system check mode screen. | Proceed to "Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter" | |
| Radio receiver assembly | ||
| Navigation computer sub-assembly |
| Symptom | Suspected Area | See page |
|---|---|---|
| No feedback force is provided by knob of remote touch. | Proceed to "No Feedback Force Provided by Knob of Remote Touch" | |
| Switch lights of remote touch do not illuminate. | Proceed to "Switch Lights of Remote Touch do not Illuminate" | |
| Switch lights of remote touch always illuminate or cannot be controlled using rheostat. | Proceed to "Switch Lights of Remote Touch Always Illuminate or cannot be Controlled Using Rheostat" | |
| Switch operation of remote touch is not accepted. | Proceed to "Switch Operation of Remote Touch not Accepted" | |
| Pointer does not reach screen edge. | Proceed to "Pointer does not Reach Screen Edge" | |
| Pointer displayed/not displayed repeatedly. | Proceed to "Pointer Displayed/not Displayed Repeatedly" | |
| Pointer is not displayed on screen or pointer does not move. | Proceed to "Pointer not Displayed on Screen or Pointer does not Move" | |
| Knob of remote touch moves spontaneously. | Proceed to "Knob of Remote Touch Moves Spontaneously" |
| Symptom | Suspected Area | See page |
|---|---|---|
| System cannot be operated by steering pad switch. | Proceed to "Panel Switches do not Function" | |
| Proceed to "Steering Pad Switch Circuit" | ||
| Navigation computer sub-assembly | ||
| The steering pad switch does not illuminate even when the light control switch is turned to the tail or head position. | Proceed to "Illumination Circuit" | |
| Navigation computer sub-assembly |
| Symptom | Suspected Area | See page |
|---|---|---|
| Bluetooth is inoperative. | Proceed to "Microphone Circuit between Microphone and Navigation ECU" | |
| Radio receiver assembly | ||
| Navigation computer sub-assembly | ||
| Cellular phone registration failure, phone directory transfer failure | Proceed to "Cellular Phone Registration Failure, Phone Directory Transfer Failure" | |
| Cellular phone cannot send/receive. | Proceed to "Cellular Phone cannot Send/Receive" | |
| Proceed to "Steering Pad Switch Circuit" | ||
| Radio receiver assembly | ||
| Navigation computer sub-assembly | ||
| Cellular phone cannot call in a certain place. | Proceed to "Cannot Call in a Certain Place" | |
| Other caller's voice cannot be heard, is too quiet, or distorted. | Proceed to "The Other Caller's Voice cannot be Heard, is too Quiet, or Distorted" | |
| Radio receiver assembly | ||
| Navigation computer sub-assembly | ||
| Stereo component amplifier assembly | ||
| Other caller cannot hear your voice, or your voice is too quiet or distorted. | Proceed to "The Other Caller cannot Hear Your Voice, or Your Voice is too Quiet or Distorted" | |
| Proceed to "Microphone Circuit between Microphone and Navigation ECU" | ||
| Radio receiver assembly | ||
| Navigation computer sub-assembly |
| Symptom | Suspected Area | See page |
|---|---|---|
| "Fuel Consumption" icon is dimmed. | Check if other icons or items displayed on screen have any problems. | - |
| Navigation computer sub-assembly | ||
| Graph is not displayed on "Consumption" screen. | Recheck with the hybrid system operating. | - |
| Navigation computer sub-assembly | ||
| Cruise range is not displayed on "Consumption" screen. | Turn power switch on (IG) and recheck. | - |
| Navigation computer sub-assembly | ||
| Graph is not updated on "Past record" screen even though "Clear" is selected. | Turn power switch on (IG) and recheck. | - |
| Navigation computer sub-assembly | ||
| Graph is not displayed on "Past record" screen. | Turn power switch on (IG) and recheck. | - |
| Reset the average fuel consumption value on the multi-information display in the combination meter assembly. | - | |
| Navigation computer sub-assembly |
*1: w/ DVD Changer