NOISE FILTER REMOVAL


  1. REMOVE REAR NO. 2 FLOOR BOARD (for Quarter)


    1. Remove the rear No. 2 floor board.

  2. REMOVE REAR DECK FLOOR BOX (for Quarter)


    1. Remove the rear deck floor box.

  3. REMOVE REAR NO. 3 FLOOR BOARD (for Quarter)


    1. Remove the rear No. 3 floor board.

  4. REMOVE DECK FLOOR BOX RH (for Quarter)


    1. A003Z5J

      Remove the clip.

    2. Disengage the 6 guides and remove the deck floor box RH.

  5. REMOVE REAR NO. 4 FLOOR BOARD (for Quarter)

    w/o Woofer: Click here

    w/ Woofer: Click here

  6. REMOVE DECK FLOOR BOX LH (for Quarter)

    w/o Woofer: Click here

  7. REMOVE TONNEAU COVER ASSEMBLY (for Quarter)

    w/ Tonneau Cover: Click here

  8. REMOVE REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY (for Quarter)


    1. A003X65

      Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board sub-assembly.

  9. REMOVE REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY (for Quarter)


    1. A003YRO

      Disengage the claw and 2 clips, and remove the rear No. 2 floor board sub-assembly.

  10. REMOVE REAR NO. 1 FLOOR BOARD (for Quarter)


    1. A003ZU1

      Remove the bolt.

    2. Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board.

  11. REMOVE DECK TRIM SERVICE HOLE COVER (for Quarter)


    1. A003YBSE01

      Disengage the 2 claws and guide (A).

    2. Disengage the 2 guides (B) and remove the deck trim service hole cover.

  12. REMOVE REAR DECK TRIM COVER (for Quarter)


    1. A003YUE

      Disengage the 4 clips and remove the rear deck trim cover.

  13. REMOVE REAR DOOR SCUFF PLATE LH (for Quarter)


    1. A003ZA0

      Disengage the 4 claws, 2 guides and 2 clips, and remove the rear door scuff plate LH.

  14. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Quarter)


    1. Remove the rear door opening trim weatherstrip LH.

    2. Remove the residual weatherstrip sealant from the body of the vehicle using cleaner.

      Note

      Remove the sealant completely. Any residual sealant may transfer to other areas of the vehicle when removing/installing the interior parts.

  15. REMOVE REAR SEAT CUSHION ASSEMBLY (for Quarter)


    1. Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

      Note

      Follow the instructions below carefully as the cushion frame can be deformed easily.


      1. A003ZN5E01
        Text in Illustration
        *1 Hook
        *2 Guide

        Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

      2. Repeat the step above for the other hook.

    2. Disengage the guide of the seat cushion from the seatback.

    3. A003YWG
      Standard Measurement
      *a 100 mm (3.94 in.) or less

      Remove the bolt and disconnect the rear center seat outer belt assembly.

    4. Pull out the rear center seat outer belt assembly from the rear seat cushion assembly.

    5. Remove the rear seat cushion assembly.

  16. REMOVE REAR SEAT CUSHION LOCK HOOK (for Quarter)


    1. A003Y4L

      Disengage the claw and remove the rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure the LH side and RH side.

  17. REMOVE REAR SEATBACK ASSEMBLY LH (for Quarter)


    1. Disengage the fastener and disconnect the rear No. 2 floor board sub-assembly.

    2. A003V5X

      Remove the 2 bolts and rear seatback assembly LH.

      Note

      Be careful not to damage the vehicle body.

  18. REMOVE REAR SEAT SIDE GARNISH LH (for Quarter)


    1. A003WIU

      Remove the clip.

    2. Disengage the 6 claws and remove the rear seat side garnish LH.

  19. REMOVE ROPE HOOK ASSEMBLY (for Quarter)


    1. A003WBHE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 2 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Remove the bolt and the rope hook assembly.

  20. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for Quarter)


    1. A003XL5

      Remove the bolt.

    2. Disengage the guide and remove the luggage hold belt striker assembly.

  21. REMOVE TONNEAU COVER HOOK (for Quarter)


    1. A003ZSDE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 2 claws and pin, and remove the tonneau cover hook.

      Tech Tips

      Tape the screwdriver tip before use.

  22. REMOVE TONNEAU COVER HOLDER CAP (for Quarter)


    1. A003XGZE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the claws and guide, and remove the tonneau cover holder cap.

      Tech Tips

      Tape the screwdriver tip before use.

  23. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for Quarter)


    1. Remove the 3 screws.

    2. Disengage the 4 claws and 3 clips, and remove the deck trim side panel assembly LH.

      A003ZDO

  24. REMOVE RADIO SETTING CONDENSER (for Quarter)

    Note

    When the terminal cover is removed, the radio setting condenser must be replaced because the terminal cover and condenser are supplied as a set.


    1. A003X3E

      Remove the bolt.

    2. Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.

    3. A003XIQ

      Using a screwdriver, disengage the 3 claws and remove the terminal cover with wire harness from the condenser.

    4. Using a screwdriver, bend back and break off the claw as shown in the illustration.

      A003YM9

    5. Remove the terminal cover from the wire harness.

  25. REMOVE ROOF HEADLINING ASSEMBLY (for Roof Side)

    Click here

  26. REMOVE RADIO SETTING CONDENSER (for Roof Side)

    Note

    When the terminal cover is removed, the radio setting condenser must be replaced because the terminal cover and condenser are supplied as a set.


    1. A003XWS

      Remove the bolt.

    2. Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.

    3. A003XIQ

      Using a screwdriver, disengage the 3 claws and remove the terminal cover with wire harness from the condenser.

    4. Using a screwdriver, bend back and break off the claw as shown in the illustration.

      A003YM9

    5. Remove the terminal cover from the wire harness.

  27. REMOVE UPPER BACK DOOR TRIM PANEL ASSEMBLY (for Back Door)


    1. A003X12

      Using a moulding remover, disengage the 4 clips and 4 claws, and remove the upper back door trim panel assembly.

  28. REMOVE BACK DOOR SIDE GARNISH LH (for Back Door)


    1. A003XEI

      Disengage the 2 clips, 2 claws and guide, and remove the back door side garnish LH.

  29. REMOVE BACK DOOR SIDE GARNISH RH (for Back Door)


    1. A003VMK

      Disengage the 2 clips, 2 claws and guide, and remove the back door side garnish RH.

  30. REMOVE BACK DOOR TRIM BOARD ASSEMBLY (for Back Door)


    1. A003ZUJ

      Using a screwdriver with its tip wrapped in protective tape, slide the handle plate of the back door trim board to disengage it.

    2. A003XVH

      Disengage the 13 clips and remove the back door trim board assembly.

  31. REMOVE RADIO SETTING CONDENSER (for Back Door)

    Note

    When the terminal cover is removed, the radio setting condenser must be replaced because the terminal cover and condenser are supplied as a set.


    1. A003Y4D

      Remove the bolt.

    2. Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.

    3. A003XIQ

      Using a screwdriver, disengage the 3 claws and remove the terminal cover with wire harness from the condenser.

    4. Using a screwdriver, bend back and break off the claw as shown in the illustration.

      A003YM9

    5. Remove the terminal cover from the wire harness.