HEATED STEERING WHEEL CONTROLLER INSTALLATION

Note


  • Do not replace the spiral cable with the auxiliary battery connected and the power switch on (IG).

  • Do not rotate the spiral cable without the steering wheel with the auxiliary battery connected and the power switch on (IG).

  • Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.

  • Do not remove the steering sensor from the spiral cable.


  1. INSTALL STEERING WHEEL HEATER CONTROL ASSEMBLY


    1. Install the steering wheel heater control assembly to the lower steering wheel boss cover with the 2 screws.

      Torque:
      0.8 N*m  { 9 kgf*cm, 7 in.*lbf }

    2. Engage the clamp.

  2. INSTALL LOWER STEERING WHEEL BOSS COVER


    1. Connect the connector to the steering wheel heater control assembly.

    2. A003V1U

      As shown in the illustration, place the wire harness along the guides.

    3. Engage the 4 claws to install the lower steering wheel boss cover to the steering wheel sub-assembly.

      Note

      Do not allow the steering heater wire harness to be caught between the lower steering wheel boss cover and the steering wheel sub-assembly.

    4. Install the 2 screws.

      Torque:
      1.7 N*m  { 17 kgf*cm, 15 in.*lbf }

  3. INSTALL STEERING SHAKE DAMPER


    1. Install the steering shake damper to the steering wheel sub-assembly with the 2 screws.

      Torque:
      2.4 N*m  { 24 kgf*cm, 21 in.*lbf }

  4. INSTALL CRUISE CONTROL SWITCH WIRE (w/ Cruise Control System)


    1. Install the cruise control switch wire.

  5. INSTALL CRUISE CONTROL SWITCH (w/ Cruise Control System)


    1. Connect the connector.

    2. A003YFP

      Install the cruise control switch with the 2 screws shown in the illustration.

      Torque:
      2.4 N*m  { 24 kgf*cm, 21 in.*lbf }

  6. INSTALL STEERING PAD SWITCH ASSEMBLY


    1. Engage the 2 claws, 2 pins and 2 guides to install the steering pad switch assembly.

    2. Install the 2 screws.

      Torque:
      2.4 N*m  { 24 kgf*cm, 21 in.*lbf }
    3. A003X21E01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Install the clamp.

    4. Pass the wire harness through the guide.

    5. Connect the steering pad switch connector to the spiral cable.

    6. A003W0M

      Pass the wire harness over the 2 guides.

  7. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  8. ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Note

    Do not adjust the spiral cable with the auxiliary battery connected and the power switch on (IG).


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A003W6Z

      Rotate the spiral cable counterclockwise slowly by hand until it stops.

      Note

      Do not turn the spiral cable using the airbag wire harness.

    4. A003WHOE02
      Text in Illustration
      *A w/o Steering Heater
      *B w/ Steering Heater
      *C Type A
      *D Type B
      *1 Alignment Mark

      Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

      Note

      Do not turn the spiral cable using the airbag wire harness.

      Tech Tips

      The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.

  9. INSTALL STEERING WHEEL ASSEMBLY


    1. A003Z6ZE01
      Text in Illustration
      *a Matchmark

      Install the steering wheel assembly aligning the matchmarks on the steering wheel assembly and steering main shaft.

    2. Install the steering wheel assembly set nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

    3. Connect the connectors to the spiral cable and steering wheel assembly.

  10. CHECK STEERING WHEEL CENTER POINT

  11. INSTALL HORN BUTTON ASSEMBLY

    Click here