PARKING BRAKE PEDAL (for RHD) INSTALLATION


  1. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY


    1. A003YKJ

      Install the parking brake control pedal assembly with the 2 bolts and nut.

      Torque:
      15 N*m  { 148 kgf*cm, 11 ft.*lbf }
    2. A003XJB

      Connect the parking brake switch connector.

    3. Engage the wire harness clamp.

    4. A003Y48E01
      Text in Illustration
      *a Fulcrum Length

      Using SST, install the bolt (A).

      SST
      09961-00950
      Torque:
      without SST
      15 N*m  { 148 kgf*cm, 11 ft.*lbf }
      with SST
      9.4 N*m  { 96 kgf*cm, 83 in.*lbf }

      Note


      • Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).

      • This torque value is effective when SST is parallel to the torque wrench.

    5. Install the No. 1 parking brake cable assembly with the 4 bolts.

      Torque:
      15 N*m  { 148 kgf*cm, 11 ft.*lbf }

    6. Engage the cable with the clamp.

    7. A003XCAE01
      Text in Illustration
      *1 Lock Nut
      *2 Adjusting Nut

      Temporarily install the lock nut.

      Tech Tips

      After adjusting parking brake pedal travel, tighten the lock nut.

  2. CONNECT NO. 1 PARKING BRAKE PULL ROD SUB-ASSEMBLY


    1. A003YMJE01
      Text in Illustration
      *a Turn
      *b Hold

      Connect the No. 1 parking brake pull rod sub-assembly to the parking brake control pedal assembly as shown in the illustration.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  3. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY


    1. Engage the 2 claws to install the No. 2 air duct sub-assembly.

  4. INSTALL FRONT FLOOR CENTER REINFORCEMENT


    1. A003YC5

      Install the front floor center reinforcement with the 4 bolts.

      Torque:
      27 N*m  { 275 kgf*cm, 20 ft.*lbf }

  5. INSTALL YAW RATE AND ACCELERATION SENSOR


    1. Connect the yaw rate and acceleration sensor connector.

      Note

      Make sure that the yaw rate and acceleration sensor connector is connected securely.

    2. Install the yaw rate and acceleration sensor with the 2 bolts.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note


      • Do not damage the yaw rate and acceleration sensor.

      • Make sure that the yaw rate and acceleration sensor is installed securely.

      • Do not use dropped or damaged parts.

      • Keep the contact surfaces of the yaw rate and acceleration sensor and the body free of foreign matter.

      • Make sure that the sensor is facing the correct direction.

  6. INSTALL NO. 2 CONSOLE BOX MOUNTING BRACKET


    1. Install the No. 2 console box mounting bracket with the 2 bolts.

    2. Engage the clamp.

  7. INSTALL MULTI-MEDIA INTERFACE ECU ASSEMBLY (w/ Audio)

    Tech Tips

    This is symmetrical to the LHD model Click here.

  8. INSTALL NO. 1 ELECTRICAL KEY OSCILLATOR

    Tech Tips

    This is symmetrical to the LHD model Click here.

  9. INSTALL NO. 1 CONSOLE BOX MOUNTING BRACKET

    Tech Tips

    This is symmetrical to the LHD model Click here.

  10. INSTALL NO. 3 CONSOLE BOX MOUNTING BRACKET

    Tech Tips

    This is symmetrical to the LHD model Click here.

  11. INSTALL CONSOLE BOX LH

    Tech Tips

    This is symmetrical to the LHD model Click here.

  12. INSTALL FRONT NO. 2 CONSOLE BOX INSERT

    Tech Tips

    This is symmetrical to the LHD model Click here.

  13. INSTALL CONSOLE BOX RH

    Tech Tips

    This is symmetrical to the LHD model Click here.

  14. INSTALL CONSOLE BOX INSERT

    Tech Tips

    This is symmetrical to the LHD model Click here.

  15. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY

    Tech Tips

    This is symmetrical to the LHD model Click here.

  16. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

    Tech Tips

    Perform the same procedure as for the LHD model Click here.

  17. INSTALL REAR CONSOLE BOX ASSEMBLY

    Tech Tips

    This is symmetrical to the LHD model Click here.

  18. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY

    Tech Tips

    This is symmetrical to the LHD model Click here.

  19. ADJUST PARKING BRAKE PEDAL TRAVEL


    1. Remove the No. 1 instrument panel under cover sub-assembly Click here.

    2. Remove the No. 2 air duct sub-assembly Click here.

    3. Completely release the parking brake pedal.

    4. A003ZCVE01
      Text in Illustration
      *1 Lock Nut
      *2 Adjusting Nut

      Loosen the lock nut and the adjusting nut to completely release the parking brake cable.

    5. Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

      Parking brake pedal travel
      8 to 11 notches at 300 N (31 kgf, 67.5 lbf)

    6. Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    7. Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.

    8. Check that the parking brake does not drag.

    9. Install the No. 2 air duct sub-assembly Click here.

    10. Install the No. 1 instrument panel under cover sub-assembly Click here.

  20. INSPECT BRAKE WARNING LIGHT


    1. When operating the parking brake pedal, check that the brake warning light illuminates.

      Standard
      The brake warning light always illuminates at the first click.