REAR SPEED SENSOR INSTALLATION

Tech Tips


  • Use the same procedure for the LH side and RH side.

  • The following procedure is for the LH side.

  • If the sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly.

  • The rear speed sensor is a component of the rear axle hub and bearing assembly. If the rear speed sensor malfunctions, replace the rear axle hub and bearing assembly.


  1. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY


    1. Install the rear axle hub and bearing assembly Click here.

      Tech Tips


      • The rear speed sensor is a component of the rear axle hub and bearing assembly. If the rear speed sensor malfunctions, replace the rear axle hub and bearing assembly.

      • If the sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly.

  2. CONNECT REAR SPEED SENSOR WIRE


    1. Connect the rear speed sensor wire connector to the rear speed sensor.

  3. INSPECT REAR AXLE HUB BEARING LOOSENESS

    A003YNW

    1. Using a dial indicator, check for looseness near the center of the rear axle hub.

      Maximum looseness
      0.05 mm (0.00197 in.)

      Note


      • Ensure that the dial indicator is set perpendicular to the measurement surface.

      • Keep the magnet of the dial indicator away from the rear axle hub and bearing assembly.

      Tech Tips

      If the looseness exceeds the maximum, replace the rear axle hub and bearing assembly.

  4. INSPECT REAR AXLE HUB RUNOUT


    1. A003V5D

      Using a dial indicator, check for runout on the surface of the rear axle hub outside the rear axle hub bolt.

      Maximum runout
      0.05 mm (0.00197 in.)

      Note


      • Ensure that the dial indicator is set perpendicular to the measurement surface.

      • Make sure to install the tip of the dial indicator towards the outside of the rear axle hub bolt.

      • Keep the magnet of the dial indicator away from the rear axle hub and bearing.

      Tech Tips

      If the runout exceeds the maximum, replace the rear axle hub and bearing assembly.

  5. INSTALL REAR DISC


    1. A003XTLE01
      Text in Illustration
      *a Matchmark

      Align the matchmarks of the disc and axle hub, and install the disc.

      Note

      When replacing the disc with a new one, select the installation position where the rear disc has minimal runout.

  6. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY


    1. Install the rear disc brake caliper assembly with the 2 bolts.

      Torque:
      57 N*m  { 585 kgf*cm, 42 ft.*lbf }

    2. Install the rear flexible hose to the No. 2 flexible hose bracket with the bolt.

      Torque:
      19 N*m  { 192 kgf*cm, 14 ft.*lbf }

  7. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. A003Z7EE01
      Text in Illustration
      *1 No. 3 Parking Brake Cable Assembly
      *2 Clip

      Install the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.

      Tech Tips

      Be sure to engage the No. 3 parking brake cable assembly clip onto the rear disc brake cylinder assembly as shown in the illustration.

    2. A003WLP

      Connect the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.

    3. Install the No. 3 parking brake cable assembly with the bolt.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

  8. INSTALL PARKING BRAKE LEVER PROTECTOR


    1. A003VOHE02

      Install the parking brake lever protector to the No. 3 parking brake cable assembly.

  9. INSTALL REAR SUSPENSION ARM COVER


    1. Insert the 2 claws of the rear suspension arm cover into the rear No. 2 suspension arm assembly.

    2. Install the rear suspension arm cover with the 2 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

      Note

      Make sure that the 2 claws of the rear suspension arm cover are inserted.

  10. ADJUST PARKING BRAKE

    Click here

  11. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for LHD)


    1. Connect each connector.

    2. A003XF4

      Engage the 8 claws and clip to install the lower instrument panel finish panel sub-assembly.

  12. INSTALL INSTRUMENT SIDE PANEL LH (for LHD)


    1. A003Y0E

      Engage the 4 guides, clip and 3 claws to install the instrument side panel LH.

  13. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for LHD)


    1. A003Y6FE01
      Text in Illustration
      *a Alignment Mark (Orange)

      Align the alignment mark (orange) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  14. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. Connect each connector.

    2. Engage the clamp.

    3. Engage the clip.

    4. Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <E>.

  15. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY (for RHD)


    1. Engage the 2 claws to install the No. 2 air duct sub-assembly.

  16. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. Connect each connector.

    2. Engage the clamp.

    3. Engage the 2 clips.

    4. Install the No. 1 instrument panel under cover sub-assembly with the screw <E>.

  17. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  18. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL


    1. Connect the cable to the negative (-) auxiliary battery terminal Click here.

    2. Connect the reservoir level switch connector.

    3. Clear the DTCs Click here.

  19. CHECK FOR SPEED SENSOR SIGNAL

    Click here