REAR COIL SPRING REMOVAL

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.


  1. REMOVE REAR WHEEL

  2. REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)


    1. A003WH7E01
      Text in Illustration
      *1 Clamp
      *2 Guide

      Disengage the clamp.

    2. Disconnect the connector.

    3. Remove the 2 bolts.

    4. Disengage the 2 guides and remove the rear height control sensor sub-assembly.

      Note

      Do not drop the rear height control sensor sub-assembly. If it is dropped, replace it with a new one.

  3. REMOVE REAR SUSPENSION ARM COVER


    1. A003W3L

      Remove the 2 bolts and disengage the 2 claws to remove the rear suspension arm cover from the rear No. 2 suspension arm assembly.

  4. REMOVE REAR FLOOR SIDE MEMBER COVER (w/ Floor Under Cover)


    1. for LH Side:


      1. A003WZU

        Remove the 2 bolts, nut and clip.

      2. Disengage the clip and remove the rear floor side member cover LH.

    2. for RH Side:


      1. A003Y2E

        Remove the bolt and nut.

      2. Disengage the 2 clips and remove the rear floor side member cover RH.

  5. REMOVE REAR SUSPENSION MEMBER BRACE


    1. A003Y81

      Remove the 3 bolts and rear suspension member brace LH from the rear suspension member sub-assembly.

  6. REMOVE REAR STABILIZER LINK ASSEMBLY


    1. A003WS1

      Remove the nut (A) and separate the rear stabilizer link assembly LH from the rear stabilizer bar.

      Text in Illustration
      A003ZV9 Nut (A)
      A003YYF Nut (B)

      Tech Tips

      If the ball joint turns together with the nut, use a hexagon socket wrench to hold the stud bolt.

    2. Remove the nut (B), rear stabilizer link assembly LH and 2 rear stabilizer cushions.

  7. REMOVE REAR COIL SPRING


    1. A003XLME01
      Text in Illustration
      *1 Wooden Block
      *2 Jack

      Support the rear axle assembly with a jack using a wooden block as shown in the illustration.

      Note

      Keep supporting the rear axle assembly with a jack until the installation of the rear coil spring has been completed.

    2. A003YBLE01
      Text in Illustration
      *1 Wooden Block
      *2 Jack
      A003ZV9 Bolt (A)
      A003YYF Bolt (B)
      A003W0J Bolt (C)

      Support the rear No. 2 suspension arm assembly using a jack and wooden block.

      Note


      • When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

      • Make sure to perform this operation with the vehicle kept as low as possible.

    3. Loosen the bolt (A).

      Note


      • Since a stopper nut is used, turn the bolt.

      • Do not remove the bolt.

    4. Remove the bolt (B) and nut, and separate the rear No. 2 suspension arm assembly from the rear axle assembly.

      Note

      Since a stopper nut is used, turn the bolt.

    5. Remove the bolt (C) and nut, and then slowly lower the rear No. 2 suspension arm assembly, and remove the rear coil spring.

      Note

      Since a stopper nut is used, turn the bolt.

  8. REMOVE REAR UPPER COIL SPRING INSULATOR


    1. Remove the rear upper coil spring insulator.

  9. REMOVE REAR LOWER COIL SPRING INSULATOR


    1. Remove the rear lower coil spring insulator.