REAR AXLE HUB BOLT REPLACEMENT

Note

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. DISABLE BRAKE CONTROL


    1. Wait at least 2 minutes after the power switch off.

      Note

      When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.

    2. A003Y4O

      Disconnect the reservoir level switch connector with the parking brake applied.

    3. Disconnect the cable from the negative (-) auxiliary battery terminal Click here.

    4. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

    5. Check that the brake pedal can not be further depressed.

    6. Release the parking brake.

  3. REMOVE REAR WHEEL

  4. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. A003Y9D

      Remove the 2 screws <E>.

    2. Disengage the clip.

    3. Disengage the clamp.

    4. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.

  5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for LHD)


    1. A003YSW

      Disconnect the front door opening trim weatherstrip.

    2. Remove the residual weatherstrip sealant from the body of the vehicle using cleaner.

      Note

      Remove the sealant completely. Any residual sealant may transfer to other areas of the vehicle when removing/installing the interior parts.

  6. REMOVE INSTRUMENT SIDE PANEL LH (for LHD)


    1. A003Z0S

      Using a moulding remover, disengage the 3 claws, clip and 4 guides, and remove the instrument side panel LH.

  7. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for LHD)


    1. A003W9H

      Using a moulding remover, disengage the 8 claws and clip.

    2. Disconnect each connector and remove the lower instrument panel finish panel sub-assembly.

  8. LOOSEN PARKING BRAKE CABLE (for LHD)


    1. Completely release the parking brake pedal.

    2. A003W4JE01
      Text in Illustration
      *1 Lock Nut
      *2 Adjusting Nut

      Loosen the lock nut and adjusting nut to completely release the parking brake cable.

  9. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. A003ZMA

      Remove the screw <E>.

    2. Disengage the 2 clips.

    3. Disengage the clamp.

    4. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.

  10. REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY (for RHD)


    1. A003WPI

      Disengage the 2 claws to remove the No. 2 air duct sub-assembly.

  11. LOOSEN PARKING BRAKE CABLE (for RHD)


    1. Completely release the parking brake pedal.

    2. A003ZCVE01
      Text in Illustration
      *1 Lock Nut
      *2 Adjusting Nut

      Loosen the lock nut and the adjusting nut to completely release the parking brake cable.

  12. REMOVE PARKING BRAKE LEVER PROTECTOR


    1. A003VOHE01

      Remove the parking brake lever protector from the No. 3 parking brake cable assembly.

  13. DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. A003YBX

      Remove the bolt and separate the No. 3 parking brake cable assembly.

    2. A003VQP

      Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.

    3. A003XAKE01
      Text in Illustration
      *1 No. 3 Parking Brake Cable Assembly
      *2 Clip
      *3 Offset Wrench (14 mm)

      Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.

      Tech Tips

      Insert an offset wrench (14 mm) at the base of the No. 3 parking brake cable assembly as shown in the illustration to disengage the clip. Pull out the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.

  14. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY


    1. A003XW0

      Remove the bolt, and separate the rear flexible hose from the No. 2 flexible hose bracket.

    2. Remove the 2 bolts, and separate the rear disc brake caliper assembly.

      Note

      Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.

  15. REMOVE REAR DISC


    1. A003XTLE01
      Text in Illustration
      *a Matchmark

      Put matchmarks on the disc and the axle hub.

    2. Remove the rear disc.

  16. REMOVE REAR AXLE HUB BOLT


    1. A003VF5E01
      Text in Illustration
      *1 Nut

      Temporarily install 2 nuts to the rear axle hub bolts as shown in the illustration.

      Recommended service nut
      Thread diameter: 12.0 mm (0.472 in.)
      Thread pitch: 1.5 mm (0.0591 in.)

      Note

      Install the nuts to prevent damage to the hub bolts.

    2. Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.

      SST
      09611-12010

      Note

      Do not damage the threads of the rear axle hub bolts.

  17. INSTALL REAR AXLE HUB BOLT


    1. A003VN6E01
      Text in Illustration
      *1 Nut
      *2 Washer

      Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.

    2. Install a washer and nut to the new rear axle hub bolt as shown in the illustration.

      Recommended service nut
      Thread diameter: 12.0 mm (0.472 in.)
      Thread pitch: 1.5 mm (0.0591 in.)

      Tech Tips

      Recommended thickness of the washer is 5 mm (0.197 in.) or more.

    3. Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the nut.

      Note


      • Install the nuts to prevent damage to the rear axle hub bolts.

      • Do not damage the threads of the rear axle hub bolts.

    4. Remove the 3 nuts and washer from the 3 rear axle hub bolts.

  18. INSTALL REAR DISC


    1. A003XTLE01
      Text in Illustration
      *a Matchmark

      Align the matchmarks of the disc and axle hub, and install the disc.

      Note

      When replacing the disc with a new one, select the installation position where the rear disc has minimal runout.

  19. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY


    1. Install the rear disc brake caliper assembly with the 2 bolts.

      Torque:
      57 N*m  { 585 kgf*cm, 42 ft.*lbf }

    2. Install the rear flexible hose to the No. 2 flexible hose bracket with the bolt.

      Torque:
      19 N*m  { 192 kgf*cm, 14 ft.*lbf }

  20. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. A003Z7EE01
      Text in Illustration
      *1 No. 3 Parking Brake Cable Assembly
      *2 Clip

      Install the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.

      Tech Tips

      Be sure to engage the No. 3 parking brake cable assembly clip onto the rear disc brake cylinder assembly as shown in the illustration.

    2. A003WLP

      Connect the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.

    3. Install the No. 3 parking brake cable assembly with the bolt.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

  21. INSTALL PARKING BRAKE LEVER PROTECTOR


    1. A003VOHE02

      Install the parking brake lever protector to the No. 3 parking brake cable assembly.

  22. ADJUST PARKING BRAKE

    Click here

  23. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for LHD)


    1. Connect each connector.

    2. A003XF4

      Engage the 8 claws and clip to install the lower instrument panel finish panel sub-assembly.

  24. INSTALL INSTRUMENT SIDE PANEL LH (for LHD)


    1. A003Y0E

      Engage the 4 guides, clip and 3 claws to install the instrument side panel LH.

  25. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for LHD)


    1. A003Y6FE01
      Text in Illustration
      *a Alignment Mark (Orange)

      Align the alignment mark (orange) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  26. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. Connect each connector.

    2. Engage the clamp.

    3. Engage the clip.

    4. Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <E>.

  27. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY (for RHD)


    1. Engage the 2 claws to install the No. 2 air duct sub-assembly.

  28. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. Connect each connector.

    2. Engage the clamp.

    3. Engage the 2 clips.

    4. Install the No. 1 instrument panel under cover sub-assembly with the screw <E>.

  29. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  30. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL


    1. Connect the cable to the negative (-) auxiliary battery terminal Click here.

    2. Connect the reservoir level switch connector.

    3. Clear the DTCs Click here.