TCM INSTALLATION


  1. INSTALL TRANSMISSION CONTROL ECU ASSEMBLY


    1. A003YKYE01
      Text in Illustration
      *A for LHD
      *B for RHD

      Engage the 2 claws to install the transmission control ECU assembly to the ECU integration box.

  2. INSTALL ECU INTEGRATION BOX RH (for LHD)


    1. Install the ECU integration box RH with the 2 nuts and bolt.

    2. Engage the clamp to connect the wire harness.

    3. Connect each connector.

  3. INSTALL ECU INTEGRATION BOX LH (for RHD)


    1. Install the ECU integration box LH with the nut and bolt.

    2. Engage the clamp to connect the wire harness.

    3. Connect each connector.

  4. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    1. Connect the connector.

    2. Engage the clamp.

    3. Engage the 5 claws.

    4. Install the glove compartment door assembly with the 4 screws <C>.

  5. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A003ZOW

      Connect the airbag connector to the lower No. 2 instrument panel airbag assembly.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    4. Push in the lock to install the airbag connector.

    5. Temporarily install the lower No. 2 instrument panel airbag assembly with the 6 claws and 2 guides.

    6. Install the 3 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Confirm that the lower No. 2 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.

  6. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. Connect the connector.

    2. Engage the clamp.

    3. Engage the guide, claw and 2 clips to install the No. 2 instrument panel under cover sub-assembly.

  7. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. Connect the connector.

    2. Engage the clamp.

    3. Engage the 2 guides, claw and 2 clips to install the No. 2 instrument panel under cover sub-assembly.

  8. INSTALL INSTRUMENT SIDE PANEL RH (for LHD)


    1. Connect the connector.

    2. A003YNR

      Engage the 4 guides, clip and 3 claws to install the instrument side panel RH.

  9. INSTALL INSTRUMENT SIDE PANEL LH (for RHD)


    1. A003Y0E

      Engage the 4 guides, clip and 3 claws to install the instrument side panel LH.

  10. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for LHD)


    1. A003W54E01
      Text in Illustration
      *a Alignment Mark (Light blue)

      Align the alignment mark (light blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  11. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for RHD)


    1. A003Y6FE01
      Text in Illustration
      *a Alignment Mark (Orange)

      Align the alignment mark (orange) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  12. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH (for LHD)

    Tech Tips

    Use the same procedure described for the LH side Click here.

  13. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH (for RHD)


    1. Engage the claw and clip.

      Note


      • Be sure to engage the clip securely.

      • If there is any damage, replace the garnish clip with a new one.

    2. Install the cowl side trim sub-assembly LH with the clip.

  14. INSTALL FRONT DOOR SCUFF PLATE RH (for LHD)

    Tech Tips

    Use the same procedure described for the LH side Click here.

  15. INSTALL FRONT DOOR SCUFF PLATE LH (for RHD)


    1. Engage the 4 claws, 2 guides and 4 clips to install the front door scuff plate LH.

  16. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  17. INSTALL REAR FLOOR BOARD UPPER NO. 3 PLATE


    1. Engage the 4 claws and 2 guides to install the rear floor board upper No. 3 plate.

  18. INSTALL DECK FLOOR BOX RH


    1. Engage the 6 guides.

    2. Install the deck floor box RH with the clip.

  19. INSTALL REAR NO. 3 FLOOR BOARD


    1. Install the rear No. 3 floor board.

  20. INSTALL REAR DECK FLOOR BOX


    1. Install the rear deck floor box.

  21. INSTALL REAR NO. 2 FLOOR BOARD


    1. Install the rear No. 2 floor board.

  22. PERFORM INITIALIZATION

    Click here

  23. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  24. INSPECT SRS WARNING LIGHT

    Click here