Click here

SHIFT LEVER REMOVAL

Click here
Click here
  1. Click here

    PRECAUTION

    Note:

    • If the transmission instrument panel shift assembly is to be replaced with a new one, it is necessary to clear the learned shift sensor voltage values by disconnecting and reconnecting the cable of the negative (-) auxiliary battery terminal.

    • After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

  2. Click here

    REMOVE REAR NO. 2 FLOOR BOARD


    1. Remove the rear No. 2 floor board.

  3. Click here

    REMOVE REAR DECK FLOOR BOX


    1. Remove the rear deck floor box.

  4. Click here

    REMOVE REAR NO. 3 FLOOR BOARD


    1. Remove the rear No. 3 floor board.

  5. Click here

    REMOVE DECK FLOOR BOX RH


    1. A003Z5J

      Remove the clip.

    2. Disengage the 6 guides and remove the deck floor box RH.

  6. Click here

    REMOVE REAR FLOOR BOARD UPPER NO. 3 PLATE


    1. A003VKN

      Disengage the 4 claws and 2 guides, and remove the rear floor board upper No. 3 plate.

  7. Click here

    DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  8. Click here

    REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A003XQZ

      Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.

  9. Click here

    REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL


    1. Open the glove compartment door.

    2. A003XK6

      Using a moulding remover, disengage the 7 claws and 4 guides, and remove the lower center instrument panel finish panel as shown in the illustration.

  10. Click here

    REMOVE UPPER NO. 2 CONSOLE PANEL GARNISH


    1. A003WH5

      Disengage the 5 claws, clip and 2 guides, and remove the upper No. 2 console panel garnish.

  11. Click here

    REMOVE UPPER NO. 1 CONSOLE PANEL GARNISH


    1. A003XQR

      Disengage the 4 claws, clip and 3 guides, and remove the upper No. 1 console panel garnish.

  12. Click here

    REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. Open the console compartment door.

    2. A003XLPE01

      Using a moulding remover, disengage the 9 claws of the vehicle rear side.

      Table 1. Text in Illustration
      *a Protective Tape - -

    3. Using a screwdriver with its tip wrapped with protective tape, disengage the 3 claws of the vehicle front side as shown in the illustration.

    4. Disengage the clamp.

    5. Disconnect each connector and remove the upper console panel sub-assembly.

  13. Click here

    REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY


    1. A003WBB

      Disengage the 6 claws and 2 guides.

    2. Disengage the clamp.

    3. Disconnect each connector and remove the integration control and panel assembly.

  14. Click here

    REMOVE REAR CONSOLE BOX POCKET


    1. A003V5Y

      Remove the rear console box pocket.

  15. Click here

    REMOVE CONSOLE BOX CARPET


    1. A003VMZ

      Remove the console box carpet.

  16. Click here

    REMOVE REAR CONSOLE BOX ASSEMBLY


    1. A003W28

      Remove the 2 screws and 4 bolts.

    2. A003YLE

      Disengage the 8 guides and remove the rear console box assembly.

  17. Click here

    REMOVE CONSOLE BOX INSERT


    1. A003Z6E

      Disengage the 2 clips and 2 claws, and remove the console box insert.

  18. Click here

    REMOVE CONSOLE BOX LH (for LHD)


    1. A003WSO

      Remove the bolt <A>.

    2. Using a clip remover, remove the clip.

    3. Using a clip remover, disengage the 3 clips.

    4. Disengage the 2 claws and guide, and remove the console box LH.

  19. Click here

    REMOVE CONSOLE BOX RH (for RHD)


    1. A003VY3

      Remove the bolt <A>.

    2. Using a clip remover, remove the clip.

    3. Using a clip remover, disengage the 3 clips.

    4. Disengage the 2 claws and guide, and remove the console box RH.

  20. Click here

    REMOVE TRANSMISSION INSTRUMENT PANEL SHIFT ASSEMBLY


    1. A003Z9I

      Remove the 3 nuts and separate the transmission instrument panel shift assembly.

    2. A003ZVQ

      Disconnect the 2 connectors and remove the transmission instrument panel shift assembly.