DRIVING SUPPORT ECU INSTALLATION

INSTALL DRIVING SUPPORT ECU ASSEMBLY (for LHD)
1. Engage the claw and install the driving support ECU assembly.
INSTALL DRIVING SUPPORT ECU ASSEMBLY (for RHD)
1. Engage the claw and install the driving support ECU assembly.
INSTALL ECU INTEGRATION BOX RH (for LHD)
1. Install the ECU integration box RH with the 2 nuts and bolt.
2. Engage the clamp to connect the wire harness.
3. Connect each connector.
INSTALL ECU INTEGRATION BOX RH (for RHD)
1. Install the ECU integration box RH with the nut.
2. Install the bolt.
3. Engage the clamp.
4. Connect each connector.
INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY (for LHD)
1. Connect the connector.
2. Engage the clamp.
3. Engage the 5 claws.
4. Install the glove compartment door assembly with the 4 screws <C>.
INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for RHD)

Tech Tips

Use the same procedure for the RH side and LH side Click here.
INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD)
1. Check that the power switch is off.
2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
  
  CAUTION:
  
  Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
3. Connect the airbag connector to the lower No. 2 instrument panel airbag assembly.
  
  Note
  
  When connecting any airbag connector, take care not to damage the airbag wire harness.
4. Push in the lock to install the airbag connector.
5. Temporarily install the lower No. 2 instrument panel airbag assembly with the 6 claws and 2 guides.
6. Install the 3 bolts.
  
  Torque:
  
  10 N*m { 102 kgf*cm, 7 ft.*lbf }
  
  Note
  
  Confirm that the lower No. 2 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.
INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)
1. Connect the connector.
2. Engage the clamp.
3. Engage the guide, claw and 2 clips to install the No. 2 instrument panel under cover sub-assembly.
INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)
1. Connect each connector.
2. Engage the clamp.
3. Engage the 2 clips.
4. Install the No. 1 instrument panel under cover sub-assembly with the screw <E>.
INSTALL INSTRUMENT SIDE PANEL RH
1. Connect the connector.
2. Engage the 4 guides, clip and 3 claws to install the instrument side panel RH.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
1. Text in Illustration
  
  *a Alignment Mark (Light blue)
  
  Align the alignment mark (light blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
  
  Note
  
  After installation, check that the corners fit correctly.
INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH (for LHD)

Tech Tips

Use the same procedure for the RH side and LH side Click here.
INSTALL FRONT DOOR SCUFF PLATE RH (for LHD)

Tech Tips

Use the same procedure for the RH side and LH side Click here.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
INSTALL REAR FLOOR BOARD UPPER NO. 3 PLATE
1. Engage the 4 claws and 2 guides to install the rear floor board upper No. 3 plate.
INSTALL DECK FLOOR BOX RH
1. Engage the 6 guides.
2. Install the deck floor box RH with the clip.
INSTALL REAR NO. 3 FLOOR BOARD
1. Install the rear No. 3 floor board.
INSTALL REAR DECK FLOOR BOX
1. Install the rear deck floor box.
INSTALL REAR NO. 2 FLOOR BOARD
1. Install the rear No. 2 floor board.
INSPECT SRS WARNING LIGHT (for LHD)

Click here