Click here

DYNAMIC RADAR CRUISE CONTROL SYSTEM, Diagnostic DTC:C1A50

Click here
Click here
DTC Code DTC Name
C1A50 Brake System
Click here

DESCRIPTION

When the driving support ECU assembly receives an electronically controlled brake system malfunction signal from the brake booster with master cylinder (skid control ECU) via the CAN communication line, DTC C1A50 is stored.

DTC No. DTC Detection Condition Trouble Area
C1A50 When signal malfunction from brake booster with master cylinder (skid control ECU) continues for 1 second while dynamic radar cruise control is operating

  • Electronically controlled brake system

  • Driving support ECU assembly
Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Click here

PROCEDURE


  1. Click here

    READ OUTPUT DTC (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Chassis / ABS/VSC/TRC / DTC.

    5. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC is output B

  2. Click here

    CHECK WHETHER DTC OUTPUT RECURS (DTC C1A50)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Clear the DTCs (Click here).

    4. Perform the following to make sure that the DTC detection conditions are met.

      Tip:

      If the detection conditions are not met, the malfunction cannot be detected.


      1. Drive the vehicle at a speed of 50 km/h (30 mph) and 170 km/h (105 mph).

      2. Turn the cruise control switch (ON-OFF button) on.

      3. Push the -/SET switch to activate the cruise control.

    5. Enter the following menus: Powertrain / Radar Cruise / DTC.

    6. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC C1A50 is output B

  3. Click here

    REPLACE DRIVING SUPPORT ECU ASSEMBLY


    1. Replace the driving support ECU assembly (Click here).


  4. Click here

    CHECK WHETHER DTC OUTPUT RECURS (DTC C1A50)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Clear the DTCs (Click here).

    4. Perform the following to make sure that the DTC detection conditions are met.

      Tip:

      If the detection conditions are not met, the malfunction cannot be detected.


      1. Drive the vehicle at a speed of 50 km/h (30 mph) and 170 km/h (105 mph).

      2. Turn the cruise control switch (ON-OFF button) on.

      3. Push the -/SET switch to activate the cruise control.

    5. Enter the following menus: Powertrain / Radar Cruise / DTC.

    6. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC C1A50 is output B

  5. Click here

    REPLACE BRAKE BOOSTER WITH MASTER CYLINDER


    1. Replace the brake booster with master cylinder (skid control ECU) (Click herefor LHD,Click herefor RHD).


  6. Click here

    CHECK WHETHER DTC OUTPUT RECURS


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Clear the DTCs (Click here).

    4. Perform the following to make sure that the DTC detection conditions are met.

      Tip:

      If the detection conditions are not met, the malfunction cannot be detected.


      1. Drive the vehicle at a speed of 50 km/h (30 mph) and 170 km/h (105 mph).

      2. Turn the cruise control switch (ON-OFF button) on.

      3. Push the -/SET switch to activate the cruise control.

    5. Enter the following menus: Powertrain / Radar Cruise / DTC.

    6. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC C1A50 is output B

  7. Click here

    END

  8. Click here

    REPLACE POWER MANAGEMENT CONTROL ECUClick here

  9. Click here

    GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEMClick here

  10. Click here

    USE SIMULATION METHOD TO CHECKClick here