Click here

FRONT DOOR BELT MOULDING INSTALLATION

Click here
Click here
  1. Click here

    PRECAUTION

    Note:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work (Click here).

  2. Click here

    INSTALL FRONT DOOR BELT MOULDING ASSEMBLY


    1. A003YRP

      Engage the 7 claws to install the front door belt moulding assembly.

  3. Click here

    INSTALL FRONT DOOR FRONT LOWER FRAME UPPER COVER

    Tip:

    When installing a new front door front lower frame upper cover, heat the vehicle body using a heat light.

    Table 1. Heating Temperature
    Item Temperature
    Vehicle Body 40 to 60°C (104 to 140°F)
    Note:

    Do not heat the vehicle body or moulding excessively.


    1. Clean the vehicle body surface.


      1. Using a heat light, heat the vehicle body surface.

      2. Remove the double-sided tape from the vehicle body.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Install a new front door front lower frame upper cover.


      1. Using a heat light, heat the vehicle body and a new front door front lower frame upper cover.

      2. Remove the release paper from the front door front lower frame upper cover.

        Tip:

        After removing the release paper, keep the exposed adhesive free from foreign matter.

      3. Engage the 2 clips and install the new front door front lower frame upper cover.

  4. Click here

    INSTALL FRONT DOOR GLASS RUN


    1. A003WDM

      Install the front door glass run.

  5. Click here

    INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


    1. A003V47

      Slide the rear door glass sub-assembly to install it as shown in the illustration.

  6. Click here

    INSTALL FRONT DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the front door panel.

    2. A003VIHE01

      Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.

      Table 2. Text in Illustration
      *1 Reference Point

    3. Attach the front door service hole cover according to the reference points on the front door panel.

      Note:

      Securely install the front door service hole cover preventing wrinkles and air bubbles.

  7. Click here

    INSTALL FRONT DOOR TRIM BRACKET (for Driver Side)


    1. A003XFU

      Install the front door trim bracket with the 2 screws.

  8. Click here

    INSTALL FRONT DOOR TRIM BRACKET (for Front Passenger Side)


    1. A003XK4

      Install the front door trim bracket with the 2 screws.

  9. Click here

    INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for Driver Side)


    1. A003VEHE01

      Connect the front door lock remote control cable assembly and front door inside locking cable assembly.

      Table 3. Text in Illustration
      *1 Front Door Inside Locking Cable Assembly
      *2 Front Door Lock Remote Control Cable Assembly

    2. w/ Seat Position Memory System:


      1. Connect the connector.

    3. A003Z92

      Engage the 11 clips and install the front door trim board sub-assembly.

    4. Install the 2 screws.

    5. Remove the protective tape.

  10. Click here

    INSTALL DOOR ARMREST COVER (for Driver Side)


    1. A003W2R

      Install the door armrest cover.

  11. Click here

    INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. Connect the connector.

    2. A003VBU

      Engage the 2 guides, 3 clips and 7 claws, and install the power window regulator master switch assembly with front door armrest base panel.

  12. Click here

    INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for Front Passenger Side)


    1. A003VRFE01

      Connect the front door lock remote control cable assembly and front door inside locking cable assembly.

      Table 4. Text in Illustration
      *1 Front Door Inside Locking Cable Assembly
      *2 Front Door Lock Remote Control Cable Assembly
    2. A003WPQ

      Engage the 11 clips and install the front door trim board sub-assembly.

    3. Install the 3 screws.

    4. Remove the protective tape.

  13. Click here

    INSTALL DOOR ASSIST GRIP ASSEMBLY (for Front Passenger Side)


    1. A003VKE

      Engage the 3 guides and install the door assist grip assembly.

    2. Install the 2 screws.

  14. Click here

    INSTALL DOOR ASSIST GRIP COVER (for Front Passenger Side)


    1. for Type A:


      1. A003WHG

        Engage the guide and 4 claws to install a new door assist grip cover.

    2. for Type B:


      1. A003YAK

        Engage the guide and 2 claws.

      2. A003Y1Z

        Push the areas shown in the illustration to engage the 2 clips and install a new door assist grip cover.

        Note:

        Push the door assist grip cover until a click sound is heard to engage the clips securely.

  15. Click here

    INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. Connect the connector.

    2. A003ZG0

      Engage the 4 guides, 3 clips and 8 claws, and install the power window regulator switch assembly with front door armrest base panel.

  16. Click here

    INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH


    1. A003XX5

      Engage the clip and claws, and install the front door lower frame bracket garnish.

  17. Click here

    INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A003Y8Q

      Engage the 3 claws and install the front door inside handle bezel plug.

  18. Click here

    CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  19. Click here

    INSTALL REAR FLOOR BOARD UPPER NO. 3 PLATE


    1. Engage the 4 claws and 2 guides to install the rear floor board upper No. 3 plate.

  20. Click here

    INSTALL DECK FLOOR BOX RH


    1. Engage the 6 guides.

    2. Install the deck floor box RH with the clip.

  21. Click here

    INSTALL REAR NO. 3 FLOOR BOARD


    1. Install the rear No. 3 floor board.

  22. Click here

    INSTALL REAR DECK FLOOR BOX


    1. Install the rear deck floor box.

  23. Click here

    INSTALL REAR NO. 2 FLOOR BOARD


    1. Install the rear No. 2 floor board.

  24. Click here

    INITIALIZE POWER WINDOW CONTROL SYSTEM

    (Click here)