HEADLIGHT LEVELING ECU (for LHD) INSTALLATION


  1. INSTALL HEADLIGHT LEVELING ECU ASSEMBLY


    1. Engage the guide.

    2. Install the headlight leveling ECU assembly with the nut.

    3. Connect the connector.

  2. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    1. Connect the connector.

    2. Engage the clamp.

    3. Engage the 5 claws.

    4. Install the glove compartment door assembly with the 4 screws <C>.

  3. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A003ZOW

      Connect the airbag connector to the lower No. 2 instrument panel airbag assembly.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    4. Push in the lock to install the airbag connector.

    5. Temporarily install the lower No. 2 instrument panel airbag assembly with the 6 claws and 2 guides.

    6. Install the 3 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Confirm that the lower No. 2 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.

  4. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. Connect the connector.

    2. Engage the clamp.

    3. Engage the guide, claw and 2 clips to install the No. 2 instrument panel under cover sub-assembly.

  5. INSTALL INSTRUMENT SIDE PANEL RH


    1. Connect the connector.

    2. A003YNR

      Engage the 4 guides, clip and 3 claws to install the instrument side panel RH.

  6. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. A003W54E01
      Text in Illustration
      *a Alignment Mark (Light blue)

      Align the alignment mark (light blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  7. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  8. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  10. INSTALL REAR FLOOR BOARD UPPER NO. 3 PLATE


    1. Engage the 4 claws and 2 guides to install the rear floor board upper No. 3 plate.

  11. INSTALL DECK FLOOR BOX RH


    1. Engage the 6 guides.

    2. Install the deck floor box RH with the clip.

  12. INSTALL REAR NO. 3 FLOOR BOARD


    1. Install the rear No. 3 floor board.

  13. INSTALL REAR DECK FLOOR BOX


    1. Install the rear deck floor box.

  14. INSTALL REAR NO. 2 FLOOR BOARD


    1. Install the rear No. 2 floor board.

  15. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  16. INSPECT SRS WARNING LIGHT

    Click here

  17. HEIGHT CONTROL SENSOR SIGNAL INITIALIZATION

    Click here

  18. ADJUST HEADLIGHT AIMING

    Click here