AIR FUEL RATIO SENSOR INSTALLATION


  1. INSTALL AIR FUEL RATIO SENSOR NO.2


    1. A003X3XE07
      Text in Illustration
      *a

      Fulcrum Length

      30 mm
      *b

      Fulcrum Length

      300 mm

      Using SST, install the air fuel ratio sensor.

      SST
      09224-00010
      Torque:
      without SST
      44 N*m  { 449 kgf*cm, 32 ft.*lbf }
      with SST
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

      Note


      • The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.) and a torque wrench with a fulcrum length of 300 mm (11.8 in.) Click here.

      • The "with SST" torque value is effective when SST is parallel to the torque wrench.

    2. Connect the air fuel ratio sensor connector and clamp.

  2. INSTALL NO. 2 CYLINDER HEAD COVER


    1. A003WMM

      Engage the 3 clips to install the cover.

      Note


      • Be sure to engage the clips securely.

      • Do not apply excessive force or hit the cover to engage the clips. This may cause the cover to break.

  3. INSPECT FOR EXHAUST GAS LEAK

  4. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)


    1. Install the outer cowl top panel sub-assembly with the 9 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    2. w/ Wiper Deicer:

      Engage the 3 clamps to install the wire harness.

    3. Engage the clamp to install the wire harness.

  5. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    1. Install the outer cowl top panel sub-assembly with the 9 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    2. w/ Wiper Deicer:

      Engage the 3 clamps to install the wire harness.

    3. Engage the clamp to install the wire harness.

  6. INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for LHD)


    1. Install the cowl body mounting reinforcement LH with the 2 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  7. INSTALL COWL BODY MOUNTING REINFORCEMENT RH (for RHD)


    1. Install the cowl body mounting reinforcement RH with the 2 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  8. INSTALL NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL (for LHD)


    1. Engage the claw and guide to install the No. 2 heater air duct splash shield seal.

  9. INSTALL NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL (for RHD)


    1. Engage the claw and guide to install the No. 2 heater air duct splash shield seal.

  10. INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL (for LHD)


    1. Engage the 2 claws to install the No. 1 heater air duct splash shield seal.

  11. INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL (for RHD)


    1. Engage the 2 claws to install the No. 1 heater air duct splash shield seal.

  12. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

    Click here