REPAIR INSTRUCTION CUSTOMIZE PARAMETERS


  1. CUSTOMIZE LEXUS PARKING ASSIST-SENSOR SYSTEM


    1. Customizing with the intelligent tester

      Note


      • When the customer requests a change in a function, first make sure that the function can be customized.

      • Be sure to make a note of the current settings before customizing.

      • When troubleshooting a function, first make sure that the function is set to the default setting.


      1. Connect the intelligent tester to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the LEXUS parking assist-sensor system on.

      4. Enter the following menus: Body / Clearance Sonar / Utility / Customize Setting.

      5. Select the setting by referring to the table below.

        Warning
        Display Default Content Setting Relevant ECU
        Rr Sensor Onset Range Wide Sets the buzzer activation range for the rear center sensors.

        Narrow or Wide


        • Narrow: 600 mm (1.97 ft.)

        • Wide: 1500 mm (4.92 ft.)

        		 Clearance warning ECU assembly
        Keep Sense Buzzer Avail Sounds the buzzer when the distance between the vehicle and obstacle does not change for more than 3 seconds.

        Not Avail or Avail


        • Not Avail: Not Available

        • Avail: Available

        		 Clearance warning ECU assembly
        Fr & Rr Buzzer Volume M2 Changes the buzzer volume setting.

        L, M1, M2, M3 or H


        • L: Low volume

        • M1: Medium low volume

        • M2: Medium volume

        • M3: Medium high volume

        • H: High volume

        		 Clearance warning ECU assembly
        Sensor
        Display Default Content Setting Relevant ECU
        Sensor Condition N Avail Makes the front sensors available when neutral (N) has been selected.

        Not Avail or Avail


        • Not Avail: Not Available

        • Avail: Available

        		 Clearance warning ECU assembly
        Reverse Range Front Sensor F Changes the operation setting for the front sensors when reverse (R) has been selected.

        F or F Stop


        • F: Front sensors are available

        • F Stop: Front sensors are not available

        		 Clearance warning ECU assembly
        Non P/R Range Rear Sensor R Stop Changes the operation setting for the rear sensors when a shift state other than park (P) or reverse (R) has been selected.

        R, Rcrn or R Stop


        • R: All rear sensors are available

        • Rcrn: Rear corner sensors are available

        • R Stop: All rear sensors are not available

        		 Clearance warning ECU assembly
        Display
        Display Default Content Setting Relevant ECU
        Display Mode All The display mode setting (when the LEXUS parking assist-sensor system is normal). All or Undisp Clearance warning ECU assembly

    2. Customizing with Multi-display

      Note


      • When the customer requests a change in a function, first make sure that the function can be customized.

      • Be sure to make a note of the current settings before customizing.

      • When troubleshooting a function, first make sure that the function is set to the default setting.


      1. Turn the power switch on (IG).

      2. Turn the LEXUS parking assist-sensor system on.

      3. Enter the following menus: Setup / Vehicle / LEXUS park assist.

      4. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Alert volume 3 Sets the buzzer activation range for the rear center sensors.

        1, 2, 3, 4 or 5


        • 1: Low volume

        • 2: Medium low volume

        • 3: Medium volume

        • 4: Medium high volume

        • 5: High volume

        		 Clearance warning ECU assembly
        Display On The display mode setting (when the LEXUS parking assist-sensor system is normal). On or Off Clearance warning ECU assembly
        Distance Wide Sets the buzzer activation range for the rear center sensors.

        Narrow or Wide


        • Narrow: 600 mm (1.97 ft.)

        • Wide: 1500 mm (4.92 ft.)

        		 Clearance warning ECU assembly

  2. CUSTOMIZE POWER DOOR LOCK CONTROL SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the intelligent tester.


      1. Connect the intelligent tester to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Main Body / Utility / Customize / Door Lock.

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Unlock Key Twice

        ON*1

        OFF*2

        		 Function that unlocks only the driver door when the driver door key cylinder is turned to unlock once, and unlock all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors. ON or OFF Main body ECU (Multiplex network body ECU)
        Auto Lock

        ON*2

        OFF*1

        		 Function that locks all doors when the vehicle speed reaches a certain level. ON or OFF Main body ECU (Multiplex network body ECU)
        Auto Lock/Shift

        ON*1

        OFF*2

        		 Function that locks all doors when the shift lever is moved to select another shift state with park (P) selected, the power switch on (READY) and all doors closed. ON or OFF Main body ECU (Multiplex network body ECU)
        Auto Unlock/Shift

        ON*1

        OFF*2

        		 Function that unlocks all doors when the P position switch (transmission shift main switch) is pushed with a shift state other than park (P) selected and the power switch on (READY). ON or OFF Main body ECU (Multiplex network body ECU)
        All Unlock/Open-Close OFF Function that unlocks the other doors when the driver door is opened within 10 seconds after the power switch is turned off. ON or OFF Main body ECU (Multiplex network body ECU)

        • *1: for G.C.C. countries, Australia and New Zealand

        • *2: except G.C.C. countries, Australia and New Zealand

    2. Customizing with the Multi-display (w/ Navigation System)


      1. Turn the power switch on (IG).

      2. Enter the following menus: MENU / Setup / Vehicle / Vehicle Customization / Door Lock Settings

      3. Select the setting by referring to the table below

        Display Default Content Setting Relevant ECU
        Unlock on second key turn

        On*1

        Off*2

        		 Function that unlocks only the driver door when the driver door key cylinder is turned to unlock once, and unlocks all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors. On or Off Main body ECU (Multiplex network body ECU)
        Speed sensitive auto locking

        On*2

        Off*1

        		 Function that locks all doors when the vehicle speed reaches a certain level. On or Off Main body ECU (Multiplex network body ECU)
        Auto lock by shift from P

        On*1

        Off*2

        		 Function that locks all doors when the shift lever is moved to select another shift state with park (P) selected, the power switch on (READY) and all doors closed. On or Off Main body ECU (Multiplex network body ECU)
        Auto unlock by shift to P

        On*1

        Off*2

        		 Function that unlocks all doors when the P position switch (transmission shift main switch) is pushed with a shift state other than park (P) selected and the power switch on (READY). On or Off Main body ECU (Multiplex network body ECU)
        Auto unlock by driver door Off Function that unlocks the other doors when the driver door is opened within 10 seconds after the power switch is turned off. On or Off Main body ECU (Multiplex network body ECU)

        • *1: for G.C.C. countries, Australia and New Zealand

        • *2: except G.C.C. countries, Australia and New Zealand

    3. Customizing with the combination meter assembly

      Tech Tips


      • Press and hold DISP switch (steering pad switch assembly) when entering an item.

      • Briefly press DISP switch (steering pad switch assembly) when selecting an item.


      1. Turn the power switch on (IG).

      2. Enter the following menus: Settings / Vehicle Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        SPEED SENSITIVE AUTO. LOCK

        ON*2

        OFF*1

        		 Function that locks all doors when the vehicle speed reaches a certain level. ON or OFF Main body ECU (Multiplex network body ECU)
        SHIFT-LINKED AUTOMATIC LOCK

        ON*1

        OFF*2

        		 Function that locks all doors when the shift lever is moved to select another shift state with park (P) selected, the power switch on (READY) and all doors closed. ON or OFF Main body ECU (Multiplex network body ECU)
        SHIFT-LINKED AUTOMATIC UNLOCK

        ON*1

        OFF*2

        		 Function that unlocks all doors when the P position switch (transmission shift main switch) is pushed with a shift state other than park (P) selected and the power switch on (READY). ON or OFF Main body ECU (Multiplex network body ECU)
        DRIVER DOOR-LINKED UNLOCK

        ON*1

        OFF*2

        		 Function that unlocks the other doors when the driver door is opened within 10 seconds after the power switch is turned off. ON or OFF Main body ECU (Multiplex network body ECU)

        *1: for G.C.C. countries, Australia and New Zealand

        *2: except G.C.C. countries, Australia and New Zealand

      4. Press and hold DISP switch (steering pad switch assembly).

      5. The setting completion screen will be displayed.

      6. Return to the item selection screen.

  3. CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the intelligent tester.


      1. Connect the intelligent tester.

      2. Turn the power switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Main Body / Utility / Customize / Wireless Door Lock.

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Wireless Control ON Function that turns wireless door lock/ON or OFF ON or OFF Main body ECU (Multiplex network body ECU)
        Hazard Answer Back ON

        When the doors are locked by wireless operation, the hazard warning lights flash once.

        When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

        		 ON or OFF Main body ECU (Multiplex network body ECU)
        Open Door Warning*4 ON The buzzer sounds when lock is pressed when any of the doors are ajar. ON or OFF Main body ECU (Multiplex network body ECU)
        Unlock 2 Operation

        ON*1

        OFF*2

        		 Function that unlocks driver door when unlock switch on electrical key transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock. ON or OFF Main body ECU (Multiplex network body ECU)
        Panic Function*3 ON Function to operate theft deterrent system by continuously pressing panic switch on electrical key transmitter for 0.8 seconds ON or OFF Main body ECU (Multiplex network body ECU)
        Auto Lock Time 30 s Function that regulates the interval between unlocking and automatic relocking of doors 30 s, 60 s or 120 s Main body ECU (Multiplex network body ECU)
        Wireless Buzzer Resp*3 ON Wireless door lock buzzer response/ON or OFF ON or OFF Main body ECU (Multiplex network body ECU)
        P/W Ope buzzer*4 ON Wireless power window buzzer response/ON or OFF ON or OFF Main body ECU (Multiplex network body ECU)
        Wireless Buzzer Vol*4 Level7 Wireless door lock buzzer volume Level7, Level6, Level5, Level4, Level3, Level2, Level1 or Level0 Main body ECU (Multiplex network body ECU)

        • *1: for G.C.C. countries, Australia and New Zealand

        • *2: except G.C.C. countries, Australia and New Zealand

        • *3: except Europe and China

        • *4: except China

    2. Customizing with the multi-display (w/ Navigation system)


      1. Turn the power switch on (IG)

      2. Enter the following menus: MENU / Setup / Vehicle / Vehicle Customization / Door Lock Setting

      3. Select the setting by referring to the table below

        Display Default Content Setting Relevant ECU
        Remote 2-press unlock

        On*1

        Off*2

        		 Function that unlocks driver door when unlock switch on transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock. On or Off Main body ECU (Multiplex network body ECU)
        Auto relock timer 30 s Function that regulates the interval between unlocking and automatic relocking of doors 30 s, 60 s or 120 s Main body ECU (Multiplex network body ECU)
        Lock/unlock feedback-lights On

        When the doors are locked by wireless operation, the hazard warning lights flash once.

        When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

        		 On or Off Main body ECU (Multiplex network body ECU)
        Lock feedback volume*3 7 Wireless door lock buzzer volume Off, 1, 2, 3, 4, 5, 6 or 7 Main body ECU (Multiplex network body ECU)

        • *1: for G.C.C. countries, Australia and New Zealand

        • *2: except G.C.C. countries, Australia and New Zealand

        • *3: except China

    3. Customizing with the combination meter assembly

      Tech Tips


      • Press and hold DISP switch (steering pad switch assembly) when entering an item.

      • Briefly press DISP switch (steering pad switch assembly) when selecting an item.


      1. Turn the power switch on (IG).

      2. Enter the following menus: Settings / Vehicle Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        REMOTE 2-PRESS UNLOCK

        ON*1

        OFF*2

        		 Function that unlocks the driver door when the unlock switch on the electrical key transmitter is pressed once, and unlocks all doors when pressed twice. If the setting is OFF, pressing the unlock switch once makes all doors unlock. ON or OFF Main body ECU (Multiplex network body ECU)
        AUTO. RELOCK TIME ADJUSTMENT 30 s Function that regulates the interval between unlocking and automatic relocking of doors. 30 s, 60 s or 120 s Main body ECU (Multiplex network body ECU)
        LOCK/UNLOCK ANSWER BACK ON

        When the doors are locked by wireless operation, the hazard warning lights flash once.

        When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

        		 ON or OFF Main body ECU (Multiplex network body ECU)
        LOCK FEEDBACK VOLUME*3 7 Wireless door lock buzzer volume 0, 1, 2, 3, 4, 5, 6 or 7 Main body ECU (Multiplex network body ECU)

        • *1: for G.C.C. countries, Australia and New Zealand

        • *2: except G.C.C. countries, Australia and New Zealand

        • *3: except China

      4. Press and hold DISP switch (steering pad switch assembly).

      5. The setting completion screen will be displayed.

      6. Return to the item selection screen.

  4. CUSTOMIZE ENTRY AND START SYSTEM (for Entry Function)

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the intelligent tester


      1. Connect the intelligent tester to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Main Body or Entry & Start / Utility / Customize / Wireless Door Lock, Entry & Start or Warning.

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Wireless Buzzer Resp*2 ON Function that buzzer answer back when entry lock or unlock operation is performed. ON or OFF Main body ECU (Multiplex network body ECU)
        Park Wait Time (Waiting time to permit unlocking door after locking) 2.5s Function that sets the period of time (lock confirmation time) that the door is prevented from being unlocked by operating the front door outside handle assembly after an entry lock operation is performed. 0.5s, 1.5s, 2.5s or 5s Certification ECU (smart key ECU assembly)

        Ignition Available Area

        (Entry ignition available area)

        		 All Function that sets the area that the key must be in before the power switch can be operated. Front or All Certification ECU (smart key ECU assembly)
        Back Door Opening Operation Long Function that opens the back door when the driver has the key and presses back door opener switch assembly (opener switch) Long, Twice or OFF Certification ECU (smart key ECU assembly)
        Key Low Battery Warning (Warn when key battery becomes weak) ON Enables or disables the sounding of the buzzer when the key battery is low and the power switch is turned off after being on (IG) for 20 minutes or more. ON or OFF Certification ECU (smart key ECU assembly)
        Door Unlock Mode All*1/Driver*2 Function that chooses the doors to be operated by entry unlock operation All or Driver Certification ECU (smart key ECU assembly)
        Auto Entry Cancel SW OFF Function that enables or disables the entry and start system. ON or OFF Certification ECU (smart key ECU assembly)
        Touch Activation Over Threshold*2 Active*4/Not Active*3 The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed. Active or Not Active Certification ECU (smart key ECU assembly)

        • *1: for Europe

        • *2: w/ Wireless Buzzer Answer Back Function

        • *3: for Australia

        • *4: for G. C. C

    2. Customizing with the multi-display (w/ Multi-display)


      1. Turn the power switch on (IG).

      2. Enter the following menus: MENU / Setup / Vehicle / Vehicle Customization / Door Lock Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Select Doors to Unlock All Doors*1/Driver's Door*2 Function that sets which doors are unlocked by the entry unlock function. All Doors or Driver's Door Certification ECU (smart key ECU assembly)
        Entry and Start System On Function that enables or disables the entry and start system. On or Off Certification ECU (smart key ECU assembly)

        • *1: for Europe

        • *2: w/ Wireless Buzzer Answer Back Function

    3. Customizing with the Combination meter assembly

      Tech Tips


      • Press and hold the DISP (steering pad switch assembly) when entering an item.

      • Briefly press the DISP (steering pad switch assembly) when selecting an item.


      1. Turn the power switch on (IG).

      2. Enter the following menus: Settings / Vehicle Settings

      3. Select the setting by referring to the table below

        Display Default Content Setting Relevant ECU
        SELECT DOORS TO UNLOCK

        ALL*1

        DRIVER*2

        		 Function that chooses the doors to be operated by entry unlock operation ALL or DRIVER Certification ECU (smart key ECU assembly)
        ENTRY AND START SYSTEM ON Function that enables or disables the entry and start system. ON or OFF Certification ECU (smart key ECU assembly)

        • *1: for Europe

        • *2: except for Europe

      4. Press and hold the DISP (steering pad switch assembly).

      5. The setting completion screen will be displayed.

      6. Return to the item selection screen.

    4. Entry unlock mode switching function

      Note

      Because the key (for card type) does not have a wireless transmitter function, it cannot be used to change the entry unlock mode.


      1. The following entry unlock modes can be selected when using the entry unlock mode switching function.


        • All door unlock mode: When the sensor of a front door outside handle assembly is touched, an entry unlock operation is performed simultaneously for all doors.

        • Driver door unlock mode: When the sensor of the front door outside handle assembly is touched, an entry unlock operation is performed for the driver door only. If any other door handle is touched, an entry unlock operation is performed simultaneously for all doors.

      2. When customizing through manual operation:


        1. Turn the power switch off.

        2. Intrusion sensor is off (Intrusion sensor cancel switch is on).

        3. Check that the LED of the key is not illuminated, and then press and hold the lock and unlock buttons of the key for 5 seconds or more while the key is in the actuation area.

        4. Check the current setting.

          Tech Tips


          • The mode changes from all door unlock mode to driver door unlock mode and then back to all door unlock mode.

          • The answer-back (wireless buzzer, buzzer in the combination meter assembly) performed for each mode is indicated in the table below.

            Currently Selected Mode Answer-back (Wireless Buzzer) Answer-back (Buzzer in Combination Meter Assembly)
            All door unlock mode Buzzer sounds twice (short beeps) Buzzer sounds once ("pong" sound)
            Driver door unlock mode Buzzer sounds 3 times (short beeps) Buzzer sounds once ("pong" sound)

        5. Release the lock and unlock buttons of the key.

        6. Check that the LED of the key is not illuminated, and then press and hold the lock and unlock buttons of the key for 5 seconds or more to change the mode.

          Tech Tips

          Repeat the procedure as necessary to select the desired mode.

        7. Unlock the doors with the wireless operation, and then open any door

        A003Y8NE03

    5. Entry cancel function

      Note

      Because the key (for card type) does not have a wireless transmitter function, it cannot be used to change the entry unlock mode.

      Tech Tips

      While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the key against the power switch.


      1. The following functions are disabled when the entry and start system is canceled.


        1. Entry unlock/lock functions

        2. Push start function

        3. Key lock-in prevention function

        4. Entry warning functions

      2. When canceling the system through manual operation:


        1. Make sure the following conditions are met:


          • The power switch is off.

          • The driver door is closed.

          • The driver door is unlocked.

        2. Press the unlock button of the key.

        3. Open the driver door within 5 seconds of completing the step above (driver door: closed at beginning of step → opened).

        4. With the driver door open, press the unlock button of the key 2 times within 5 seconds of completing the step above.

          Note

          If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

        5. Close and open the driver door twice within 30 seconds of completing the above step (driver door: open at beginning of step → closed → opened → closed → opened).

        6. With the driver door open, press the unlock button of the key 2 times within 30 seconds of completing the step above.

          Note

          If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

        7. Close and open the driver door within 30 seconds of completing the step above (driver door: open at beginning of step → closed → opened).

        8. Close the driver door within 5 seconds of completing the above step.

        9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the entry and start system has been canceled.

      3. Perform the following procedure to restore the entry and start system to the active state from the canceled state.


        1. Perform the procedures to cancel the entry and start system again.

        2. Check that the wireless buzzer sounds once (short beep) to confirm that the entry and start system has been restored to the active state.

          Tech Tips


          • The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.

          • The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.

  5. CUSTOMIZE ENTRY AND START SYSTEM (for Start Function)

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the intelligent tester


      1. Connect the intelligent tester to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the intelligent tester on.

      4. Body / Entry&Start / Utility / Customize / Entry&Start or Warning

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Auto Entry Cancel SW OFF Function that enables or disables the entry and start system. ON or OFF Certification ECU (smart key ECU assembly)

        Ignition Available Area

        (Entry ignition available area)

        		 All Function that sets the area that the key must be in before the power switch can be operated. Front or All Certification ECU (smart key ECU assembly)
        Key Low Battery Warning (Warn when key battery becomes weak) ON Enables or disables the sounding of the buzzer when the key battery is low and the power switch is turned off after being on (IG) for 20 minutes or more. ON or OFF Certification ECU (smart key ECU assembly)

    2. Customizing with the multi-display (w/ Multi-display)


      1. Turn the power switch on (IG).

      2. Enter the following menus: MENU / Setup / Vehicle / Vehicle Customization / Door Lock Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Entry and Start System On Function that enables or disables the entry and start system. On or Off Certification ECU (smart key ECU assembly)

    3. Customizing with the Combination meter assembly (w/o Multi-display)

      Tech Tips


      • Press and hold the DISP (steering pad switch assembly) when entering an item.

      • Briefly press the DISP (steering pad switch assembly) when selecting an item.


      1. Turn the power switch on (IG).

      2. Enter the following menus: Settings / Vehicle Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        ENTRY AND START SYSTEM ON Function that enables or disables the entry and start system. ON or OFF Certification ECU (smart key ECU assembly)

      4. Press and hold the DISP (steering pad switch assembly).

      5. The setting completion screen will be displayed.

      6. Return to the item selection screen.

    4. Entry cancel function (manual operation)

      Note

      Because the key (for card type) does not have a wireless transmitter function, it cannot be used to change the entry unlock mode.

      Tech Tips

      While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the key against the power switch.


      1. The following functions are disabled when the entry and start system is canceled.


        1. Entry unlock/lock functions

        2. Push-button start function

        3. Key lock-in prevention function

        4. Entry warning functions

      2. When canceling the system through manual operation:


        1. Make sure the following conditions are met:


          • The power switch is off.

          • The driver door is closed.

          • The driver door is unlocked.

        2. Press the unlock button of the key.

        3. Open the driver door within 5 seconds of completing the step above (driver door: closed at beginning of step → opened).

        4. With the driver door open, press the unlock button of the key 2 times within 5 seconds of completing the step above.

          Note

          If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

        5. Close and open the driver door twice within 30 seconds of completing the above step (driver door: open at beginning of step → closed → opened → closed → opened).

        6. With the driver door open, press the unlock button of the key 2 times within 30 seconds of completing the step above.

          Note

          If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

        7. Close and open the driver door within 30 seconds of completing the step above (driver door: open at beginning of step → closed → opened).

        8. Close the driver door within 5 seconds of completing the above step.

        9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the entry and start system has been canceled.

      3. Perform the following procedure to restore the entry and start system to the active state from the canceled state.


        1. Perform the procedures to cancel the entry and start system again.

        2. Check that the wireless buzzer sounds once (short beep) to confirm that the entry and start system has been restored to the active state.

          Tech Tips


          • The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.

          • The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.

  6. CUSTOMIZE PUSH-BUTTON START SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the intelligent tester


      1. Connect the intelligent tester to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Entry&Start / Utility / Customize / Entry&Start or Warning.

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Auto Entry Cancel SW OFF Function that enables or disables the push-button start system. ON or OFF Certification ECU (smart key ECU assembly)

        Ignition Available Area

        (Entry ignition available area)

        		 All Function that sets the area that the key must be in before the power switch can be operated. Front or All
        Key Low Battery Warning (Warn when key battery becomes weak) ON Enables or disables the sounding of the buzzer when the key battery is low and the power switch is turned off after being on (IG) for 20 minutes or more. ON or OFF

    2. Customizing with the multi-display (w/ Multi-display)


      1. Turn the power switch on (IG).

      2. Enter the following menus: MENU / Setup / Vehicle / Vehicle Customization / Door Lock Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Entry and Start System On Function that enables or disables the entry and start system. On or Off Certification ECU (smart key ECU assembly)

    3. Customizing with the Combination meter assembly

      Tech Tips


      • Press and hold DISP (steering pad switch assembly) when entering an item.

      • Briefly press DISP (steering pad switch assembly) when selecting an item.


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETTINGS / VEHICLE SETTINGS

      3. Select the setting by referring to the table below

        Display Default Content Setting Relevant ECU
        ENTRY AND START SYSTEM ON Function that enables or disables the push-button start system. ON or OFF Certification ECU (smart key ECU assembly)

      4. Press and hold DISP (steering pad switch assembly).

      5. The setting completion screen will be displayed.

      6. Return to the item selection screen.

    4. Push-button start cancel function (manual operation)

      Tech Tips

      While the push-button start system is canceled, the push-button start system can be operated by holding the key against the power switch.


      1. The following functions are disabled when the push-button start system is canceled.


        1. Push-button start function

        2. Key lock-in prevention function

        3. Push-button start warning functions

      2. When canceling the system through manual operation:


        1. Make sure the following conditions are met:


          • The power switch is off.

          • The driver door is closed.

          • The driver door is unlocked.

        2. Press the unlock button of the key.

        3. Open the driver door within 5 seconds of completing the step above (driver door: closed at beginning of step → opened).

        4. With the driver door open, press the unlock button of the key 2 times within 5 seconds of completing the step above.

          Note

          If the driver door is closed before or while pressing the unlock button, the push-button start cancel setting mode will end.

        5. Close and open the driver door twice within 30 seconds of completing the step above (driver door: open at beginning of step → closed → opened → closed → opened).

        6. With the driver door open, press the unlock button of the key 2 times within 30 seconds of completing the step above.

          Note

          If the driver door is closed before or while pressing the unlock button, the push-button start cancel setting mode will end.

        7. Close and open the driver door within 30 seconds of completing the step above (driver door: open at beginning of step → closed → opened)

        8. Close the driver door within 5 seconds of completing the step above.

        9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the push-button start system has been canceled.

      3. Perform the following procedure to restore the push-button start system to the active state from the canceled state.


        1. Perform the procedures to cancel the push-button start system again.

        2. Check that the wireless buzzer sounds once (short beep) to confirm that the push-button start system has been restored to the active state.

          Tech Tips


          • The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.

          • The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.

  7. CUSTOMIZE THEFT DETERRENT SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the intelligent tester


      1. Connect the intelligent tester to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Main Body / Utility / Customize / Security or Wireless Door Lock

      5. Select the setting by referring to the table below.

        Security
        Display Default Content Setting Relevant ECU
        Intrusion Win Opened*1 OFF This function sets the sensitivity of the intrusion sensor when a door window is open. ON or OFF Main Body ECU (Multiplex Network Body ECU)
        Security control with mechanism key*2 OFF This function set to be able to release security alarm with the mechanism key ON or OFF
        Intrusion Sensor Sensitivity Level*1 N+Sound This function that adjusts sensitivity of the sensor that detects the invasion. Normal, Low, Lowest, High, Highest or N+Sound

        • *1: w/o Door Ajar Warning Buzzer Function

        • *2: w/ Airbag Cut Off Switch

        Wireless Door Lock
        Display Default Content Setting Relevant ECU
        Panic Function*1 ON This function operates the theft deterrent system when the panic switch is pressed and held for 0.8 seconds. ON or OFF Main Body ECU (Multiplex Network Body ECU)

        • *: w/ Panic Switch

  8. CUSTOMIZE LIGHTING SYSTEM (INT)


    1. Customizing with the intelligent tester

      Tech Tips

      The following items can be customized.

      Note


      • When the customer requests a change in a function, first make sure that the function can be customized.

      • Be sure to make a note of the current settings before customizing.

      • When troubleshooting a function, first make sure that the function is set to the default setting.


      1. Connect the intelligent tester to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Main Body / Utility / Customize / Illuminated Entry.

      5. Select the setting by referring to the table below.

        Illuminated Entry
        Tester Display Default Content Setting Relevant ECU
        Lighting Time 15 s Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or IG).) 7.5 s, 15 s or 30 s Main body ECU (Multiplex network body ECU)
        I/L when ACC OFF ON Lights up the power switch illumination, front interior lights and rear interior light when the power switch is turned from on (ACC or IG) to off. ON or OFF
        I/L ON W/Door Key Unlock ON Lights up the power switch illumination, front interior lights and rear interior light when doors are unlocked using a mechanical key or door control transmitter. ON or OFF
        Room Light when Aprchd ON Lights up the power switch illumination, front interior lights, rear interior light and footwell lights when a key enters any actuation area around the doors. ON or OFF
        Inside Foot Light ON Lights up the footwell lights illumination. ON or OFF
        Center Console Spot Light ON Lights up the center console spot light when the power switch is turned on (ACC or IG). ON or OFF
        Light Control ON

        Dims (ON setting) or turns off (OFF setting) the footwell lights when all of the following conditions are met:


        • The power switch is on (IG).

        • The shift lever is moved to select a shift state other than park (P).

        • All doors are closed.

        		 ON or OFF
        Interior Light Control ON Lights up the front interior lights, footwell lights and center console spot light when the illuminated entry function is operating. ON or OFF

    2. Customizing using the Multi-display


      1. Turn the power switch on (IG).

      2. Enter the following menus: MENU / Setup / Vehicle / Vehicle customization / Lights settings.

      3. Select the setting by referring to the table below:

        Lights settings
        Display Default Content Setting Relevant ECU
        Interior lights off timer 15 sec. Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or IG).) Off, 7.5 sec., 15 sec., or 30 sec. Main body ECU (Multiplex network body ECU)

    3. Customizing with the combination meter assembly

      Tech Tips


      • Press and hold the DISP switch (steering pad switch assembly) when entering an item.

      • Briefly press the DISP switch (steering pad switch assembly) when selecting an item.


      1. Turn the power switch on (IG).

      2. Enter the following menus: Settings / Vehicle Settings

      3. Select the setting by referring to the table below

        Display Default Content Setting Relevant ECU
        Int. Lights Off Adjustment 15 sec. Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or IG).) 15 sec., 7.5 sec., 30 sec. or OFF Main body ECU (Multiplex network body ECU)

      4. Press and hold the DISP switch (steering pad switch assembly).

      5. The setting completion screen will be displayed.

      6. Return to the item selection screen.

  9. CUSTOMIZE METER / GAUGE SYSTEM


    1. Customizing with the intelligent tester


      1. Connect the intelligent tester to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus:


        1. for Warning: Customize Setting / Combination Meter / Warning.

        2. for Display: Customize Setting / Combination Meter / Display.

      5. Select the setting by referring to the table below.

        Note


        • Be sure to record the current value before customizing.

        Tech Tips

        The following items can be customized using the intelligent tester.

        Warning
        Tester Display Default Content Setting Relevant ECU
        Driver Side Seatbelt Warning Buzzer*1 ON Function to turn on/off the seat belt warning buzzer ON or OFF Combination meter assembly
        Front Passenger Side Seatbelt Warning Buzzer*1 ON Function to turn on/off the seat belt warning buzzer ON or OFF Combination meter assembly
        Rear Seatbelt Warning Buzzer*2 ON Function to turn on/off the rear seat belt warning buzzer ON or OFF Combination meter assembly
        Reverse Buzzer Continual Function to change the type of the reverse warning buzzer Single or Continual Combination meter assembly

        • *1: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more

        • *2: w/ Rear Seat Belt Warning

    2. Customizing with the combination meter assembly

      Tech Tips


      • Press and hold the DISP switch (steering pad switch assembly) when entering an item.

      • Briefly pressed the DISP switch (steering pad switch assembly) when selecting an item.


      1. Turn the power switch on (IG).

      2. Select the following menus: SETTINGS / METER SETTING.

      3. Select the setting by referring to the table below.

        Note


        • Be sure to record the current value before customizing.

        Tech Tips

        The following items can be customized operating the combination meter assembly.

        Meter Setting
        Tester Display Default Content Setting Relevant ECU
        TACHO METER AUTO Function to change the tachometer setting AUTO, KEEP ON, OFF Combination meter assembly
        ECO LAMP ECO DRIVE SUPPORT Function to change the illumination level ECO DRIVE SUPPORT, KEEP ON, OFF Combination meter assembly
        SPORT LAMP AUTO Function to change the sport illumination AUTO, OFF Combination meter assembly
        LAMP BRIGHTNESS STANDARD Function to change the illumination light BRIGHT, STANDARD Combination meter assembly
        EV INDICATOR AUTO Function to change the EV indicator setting AUTO, OFF Combination meter assembly
        LANGUAGE ENGLISH Function to change the multi-information display language ENGLISH, FRENCH, SPANISH Combination meter assembly
        UNITS KM (L/1100KM) or MILES (MPG)*1 Function to change the multi-information display unit KM (KM/L), KM (L/100KM), MILES (MPG) Combination meter assembly

        • *1: The default setting is changed according to the vehicle specification

      4. Press and hold DISP switch (steering pad switch assembly).

      5. The setting completion screen will be displayed.

      6. Return to the item selection screen.

  10. CUSTOMIZE SEAT BELT WARNING SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.

    • These buzzers should be ON for safe driving. Perform this procedure only if it is necessary to set the buzzer to OFF (disabled).


    1. Customizing with the intelligent tester


      1. Connect the intelligent tester to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Combination Meter / Utility / Customize / Warning.

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Driver Side Seatbelt Warning Buzzer ON Function to sound the driver seat belt warning buzzer ON/OFF Combination meter assembly
        Front Passenger Side Seatbelt Warning Buzzer ON Function to sound the front passenger seat belt warning buzzer ON/OFF
        Rear Seatbelt Warning Buzzer* ON Function to sound the rear seat belt warning buzzer ON/OFF

        • *: w/ Rear Seat Belt Warning

        Tech Tips

        This setting is only valid when the vehicle is driven at 20 km/h (12 mph) or more.

  11. CUSTOMIZE AIR CONDITIONING SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the intelligent tester


      1. Connect the intelligent tester to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Air Conditioner / Utility / Customize.

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Set Temperature Shift Normal Function to control with the shifted temperature against the displayed temperature +2 C, +1 C, Normal, -1 C or -2 C Air conditioning amplifier assembly
        Compressor Mode Automatic Function to automatically turn the A/C on by pressing the AUTO button when blower is on and the A/C is off Manual or Automatic Air conditioning amplifier assembly
        Air Inlet Mode Automatic Function to shift from INLET mode to RECIRCULATION mode when the A/C is turned on Manual or Automatic Air conditioning amplifier assembly
        Foot/DEF Auto Mode ON Function to automatically turn the airflow from FOOT/DEF on when AUTO mode is on OFF or ON Air conditioning amplifier assembly
        Foot/DEF Automatic Blow Up Function ON Function to automatically increase the blower level when the defroster is on OFF or ON Air conditioning amplifier assembly
        Ambient Temperature Shift Normal Function to control the shifted ambient temperature in relation to the displayed ambient temperature +3 C, +2 C, +1 C, Normal, -1 C, -2 C or -3 C Air conditioning amplifier assembly
        ECO MODE Cancel OFF Function to cancel the ECO mode drive when item is on OFF or ON Air conditioning amplifier assembly
        Noise and Vibration Reduction OFF Function to change speed of the compressor when item is on OFF or ON Air conditioning amplifier assembly

    2. Customizing with Multi-display (w/ Navigation System)


      1. Turn the power switch on (IG).

      2. Select the following menus: MENU / Setup / Vehicle / Vehicle customization / Climate settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Auto A/C Mode Automatic Function to automatically turn the A/C on by pressing the AUTO button when blower is on and the A/C is off Manual or Automatic Air conditioning amplifier assembly
        Efficient Ventilation Mode Automatic Function to shift from INLET mode to RECIRCULATION mode when the A/C is turned on Manual or Automatic Air conditioning amplifier assembly

    3. Customizing with the combination meter assembly

      Tech Tips


      • Press and hold DISP switch (steering pad switch assembly) when entering an item.

      • Briefly press DISP switch (steering pad switch assembly) when selecting an item.


      1. Turn the power switch on (IG).

      2. Enter the following menus: Settings / Vehicle Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Auto A/C Mode Automatic Function to shift from INLET mode to RECIRCULATION mode when the A/C is turned on Manual or Automatic Air conditioning amplifier assembly

      4. Press and hold DISP switch (steering pad switch assembly).

      5. The setting completion screen will be displayed.

      6. Return to the item selection screen.

  12. CUSTOMIZE POWER WINDOW CONTROL SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function(s) can be customized.

    • Be sure to make notes of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the intelligent tester


      1. Connect the intelligent tester to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Main Body / Utility / Customize / Power Window.

      5. Select the setting by referring to the table below.

        Power Window
        Tester Display Default Content Setting Relevant ECU
        Door Key P/W Up OFF This function is used to close the windows by operating the mechanical key. ON/OFF Main body ECU (Multiplex network body ECU)
        Door Key P/W Down OFF This function is used to open the windows by operating the mechanical key. ON/OFF Main body ECU (Multiplex network body ECU)
        P/W Up w/ Transmitter OFF This function is used to close the windows using the wireless key transmitter. ON/OFF Main body ECU (Multiplex network body ECU)
        P/W Down w/ Transmitter OFF This function is used to open the windows using the wireless key transmitter. ON/OFF Main body ECU (Multiplex network body ECU)
        P Window Auto Up Avail This function is used to enable or disable the auto up function for the front passenger door window using the power window regulator switch assembly (for front passenger side). Avail/Not Avl Power window ECU (Power window regulator motor assembly)
        P Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the front passenger door window using the multiplex network master switch assembly. Avail/Not Avl Power window ECU (Power window regulator motor assembly)
        RR Window Auto Up Avail This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear RH side). Avail/Not Avl Power window ECU (Power window regulator motor assembly)
        RR Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the rear RH door window using the multiplex network master switch assembly. Avail/Not Avl Power window ECU (Power window regulator motor assembly)
        RL Window Auto Up Avail This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear LH side). Avail/Not Avl Power window ECU (Power window regulator motor assembly)
        RL Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the rear LH door window using the multiplex network master switch assembly. Avail/Not Avl Power window ECU (Power window regulator motor assembly)

  13. CUSTOMIZE LIGHTING SYSTEM (EXT)

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the intelligent tester


      1. Connect the intelligent tester to the DLC3.

      2. Turn the power switch to on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus:


        1. for Illuminated Entry: Body / Main Body / Utility / Customize / Illuminated Entry.

        2. for Light Control: Body / Main Body / Utility / Customize / Light Control.

      5. Select the setting by referring to the table below.

        Illuminated Entry
        Display Default Content Setting Relevant ECU
        Mirr-Foot-Lgt Approached ON Lights up the door mirror foot lights when a key enters any actuation area around the doors. ON or OFF Main Body ECU (Multiplex Network Body ECU)
        Mirr-Foot-Lgt Unlocked ON Lights up the door mirror foot lights when doors are unlocked using a mechanical key or door control transmitter. ON or OFF
        Mirr-Foot-Lgt w/Master SW ON

        • Lights up the door mirror foot lights when the driver side door control switch on the multiplex network master switch assembly is pushed to the unlock position.

        • Lights up the door mirror foot lights when the front passenger side door control switch on the power window regulator switch assembly is pushed to the unlock position.

        		 ON or OFF
        Mirror Foot Lighting Time 15 s Changes the lighting time of the door mirror foot lights. 7.5 s, 15 s, 30 s or 0 s*1
        Exterior Light Control ON Changes the door mirror foot light control. ON or OFF

        • *1: Even if "0 s" is selected, it can not be set.

        Light Control
        Display Default Content Setting Relevant ECU
        Response Time*1 Normal Changes the delay timing of lighting the taillights when going into a tunnel when the light control switch is in the AUTO position Normal or Long Main Body ECU (Multiplex Network Body ECU)
        Sensitivity Normal Adjusts the sensitivity of the automatic light control system. Light2, Light1, Normal, Dark1 or Dark2
        DRL Function ON ON/OFF of the DRL function ON or OFF
        Disp Ex ON Sen Normal Changes the ambient brightness level required to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock. Light2, Light1, Normal, Dark1 or Dark2
        Disp Ex OFF Sen Normal Changes the ambient brightness level required to cancel the dimming of the lights such as the indicator lights of the combination meter, A/C indicator light and clock. Light2, Light1, Normal, Dark1 or Dark2

        • *1: w/o Light Reminder

    2. Customizing with the Multi-display


      1. Turn the power switch on (IG).

      2. Enter the following menus: MENU / Setup / Vehicle / Vehicle customization / Light settings.

      3. Select the setting by referring to the table below.

        Light settings
        Display Default Content Setting Relevant ECU
        Light sensor sensitivity 0 Adjusts the sensitivity of the automatic light control system.*1 -2, -1, 0, +1 or +2 Main Body ECU (Multiplex Network Body ECU)
        Daytime running lights On ON/OFF of the DRL function On or Off
        Exterior lights off timer 15 sec. Changes the lighting time of the door mirror foot lights. Off, 7.5 sec., 15 sec. or 30 sec.

        • *1: The higher the setting value is, the more the lights come on easily.

    3. Customizing with the Combination meter assembly

      Tech Tips


      • Press and hold DISP (steering pad switch) when entering an item.

      • Briefly press DISP (steering pad switch) when selecting an item.


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETTINGS / VEHICLE SETTINGS.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        LIGHT SENSOR SENSITIVITY 0 (Standard) Adjusts the sensitivity of the automatic light control system.*1 -2, -1, 0, 1 or 2 Main Body ECU (Multiplex Network Body ECU)
        DAYTIME RUNNING LIGHTS ON ON/OFF of the DRL function ON or OFF
        EXTERIOR LIGHTS OFF TIME ADJUSTMENT 15 s Changes the lighting time of the door mirror foot lights. 7.5 s, 15 s, 30 s or OFF*2

        • *1: The higher the setting value is, the more the lights come on easily.

        • *2: Even if "OFF" is selected, it can not be set.