REPAIR INSTRUCTION CUSTOMIZE PARAMETERS

CUSTOMIZE LEXUS PARKING ASSIST-SENSOR SYSTEM

1. Customizing with the intelligent tester

   Note

   
   

   • When the customer requests a change in a function, first make sure that the function can be customized.

   • Be sure to make a note of the current settings before customizing.

   • When troubleshooting a function, first make sure that the function is set to the default setting.

   
   

   1. Connect the intelligent tester to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the LEXUS parking assist-sensor system on.

   4. Enter the following menus: Body / Clearance Sonar / Utility / Customize Setting.

   5. Select the setting by referring to the table below.

      Warning

      Display	Default	Content	Setting	Relevant ECU
      Rr Sensor Onset Range	Wide	Sets the buzzer activation range for the rear center sensors.	Narrow or Wide Narrow: 600 mm (1.97 ft.) Wide: 1500 mm (4.92 ft.)	Clearance warning ECU assembly
      Keep Sense Buzzer	Avail	Sounds the buzzer when the distance between the vehicle and obstacle does not change for more than 3 seconds.	Not Avail or Avail Not Avail: Not Available Avail: Available	Clearance warning ECU assembly
      Fr & Rr Buzzer Volume	M2	Changes the buzzer volume setting.	L, M1, M2, M3 or H L: Low volume M1: Medium low volume M2: Medium volume M3: Medium high volume H: High volume	Clearance warning ECU assembly

      Sensor

      Display	Default	Content	Setting	Relevant ECU
      Sensor Condition N	Avail	Makes the front sensors available when neutral (N) has been selected.	Not Avail or Avail Not Avail: Not Available Avail: Available	Clearance warning ECU assembly
      Reverse Range Front Sensor	F	Changes the operation setting for the front sensors when reverse (R) has been selected.	F or F Stop F: Front sensors are available F Stop: Front sensors are not available	Clearance warning ECU assembly
      Non P/R Range Rear Sensor	R Stop	Changes the operation setting for the rear sensors when a shift state other than park (P) or reverse (R) has been selected.	R, Rcrn or R Stop R: All rear sensors are available Rcrn: Rear corner sensors are available R Stop: All rear sensors are not available	Clearance warning ECU assembly

      Display

      Display	Default	Content	Setting	Relevant ECU
      Display Mode	All	The display mode setting (when the LEXUS parking assist-sensor system is normal).	All or Undisp	Clearance warning ECU assembly

2. Customizing with Multi-display

   Note

   
   

   • When the customer requests a change in a function, first make sure that the function can be customized.

   • Be sure to make a note of the current settings before customizing.

   • When troubleshooting a function, first make sure that the function is set to the default setting.

   
   

   1. Turn the power switch on (IG).

   2. Turn the LEXUS parking assist-sensor system on.

   3. Enter the following menus: Setup / Vehicle / LEXUS park assist.

   4. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      Alert volume	3	Sets the buzzer activation range for the rear center sensors.	1, 2, 3, 4 or 5 1: Low volume 2: Medium low volume 3: Medium volume 4: Medium high volume 5: High volume	Clearance warning ECU assembly
      Display	On	The display mode setting (when the LEXUS parking assist-sensor system is normal).	On or Off	Clearance warning ECU assembly
      Distance	Wide	Sets the buzzer activation range for the rear center sensors.	Narrow or Wide Narrow: 600 mm (1.97 ft.) Wide: 1500 mm (4.92 ft.)	Clearance warning ECU assembly

CUSTOMIZE POWER DOOR LOCK CONTROL SYSTEM

1. Customizing with the intelligent tester.

   
   

   1. Connect the intelligent tester to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the intelligent tester on.

   4. Enter the following menus: Body / Main Body / Utility / Customize / Door Lock.

   5. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      Unlock Key Twice	ON*1 OFF*2	Function that unlocks only the driver door when the driver door key cylinder is turned to unlock once, and unlock all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors.	ON or OFF	Main body ECU (Multiplex network body ECU)
      Auto Lock	ON*2 OFF*1	Function that locks all doors when the vehicle speed reaches a certain level.	ON or OFF	Main body ECU (Multiplex network body ECU)
      Auto Lock/Shift	ON*1 OFF*2	Function that locks all doors when the shift lever is moved to select another shift state with park (P) selected, the power switch on (READY) and all doors closed.	ON or OFF	Main body ECU (Multiplex network body ECU)
      Auto Unlock/Shift	ON*1 OFF*2	Function that unlocks all doors when the P position switch (transmission shift main switch) is pushed with a shift state other than park (P) selected and the power switch on (READY).	ON or OFF	Main body ECU (Multiplex network body ECU)
      All Unlock/Open-Close	OFF	Function that unlocks the other doors when the driver door is opened within 10 seconds after the power switch is turned off.	ON or OFF	Main body ECU (Multiplex network body ECU)

      *1: for G.C.C. countries, Australia and New Zealand

      *2: except G.C.C. countries, Australia and New Zealand

2. Customizing with the combination meter assembly

   Tech Tips

   
   

   • Press and hold DISP switch (steering pad switch assembly) when entering an item.

   • Briefly press DISP switch (steering pad switch assembly) when selecting an item.

   
   

   1. Turn the power switch on (IG).

   2. Enter the following menus: Settings / Vehicle Settings.

   3. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      SPEED SENSITIVE AUTO. LOCK	ON*2 OFF*1	Function that locks all doors when the vehicle speed reaches a certain level.	ON or OFF	Main body ECU (Multiplex network body ECU)
      SHIFT-LINKED AUTOMATIC LOCK	ON*1 OFF*2	Function that locks all doors when the shift lever is moved to select another shift state with park (P) selected, the power switch on (READY) and all doors closed.	ON or OFF	Main body ECU (Multiplex network body ECU)
      SHIFT-LINKED AUTOMATIC UNLOCK	ON*1 OFF*2	Function that unlocks all doors when the P position switch (transmission shift main switch) is pushed with a shift state other than park (P) selected and the power switch on (READY).	ON or OFF	Main body ECU (Multiplex network body ECU)
      DRIVER DOOR-LINKED UNLOCK	ON*1 OFF*2	Function that unlocks the other doors when the driver door is opened within 10 seconds after the power switch is turned off.	ON or OFF	Main body ECU (Multiplex network body ECU)

      *1: for G.C.C. countries, Australia and New Zealand

      *2: except G.C.C. countries, Australia and New Zealand

   4. Press and hold DISP switch (steering pad switch assembly).

   5. The setting completion screen will be displayed.

   6. Return to the item selection screen.

CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM

1. Customizing with the intelligent tester.

   
   

   1. Connect the intelligent tester.

   2. Turn the power switch on (IG).

   3. Turn the intelligent tester on.

   4. Enter the following menus: Body / Main Body / Utility / Customize / Wireless Door Lock.

   5. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      Wireless Control	ON	Function that turns wireless door lock/ON or OFF	ON or OFF	Main body ECU (Multiplex network body ECU)
      Hazard Answer Back	ON	When the doors are locked by wireless operation, the hazard warning lights flash once. When the doors are unlocked by wireless operation, the hazard warning lights flash twice.	ON or OFF	Main body ECU (Multiplex network body ECU)
      Open Door Warning*4	ON	The buzzer sounds when lock is pressed when any of the doors are ajar.	ON or OFF	Main body ECU (Multiplex network body ECU)
      Unlock 2 Operation	ON*1 OFF*2	Function that unlocks driver door when unlock switch on electrical key transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock.	ON or OFF	Main body ECU (Multiplex network body ECU)
      Panic Function*3	ON	Function to operate theft deterrent system by continuously pressing panic switch on electrical key transmitter for 0.8 seconds	ON or OFF	Main body ECU (Multiplex network body ECU)
      Auto Lock Time	30 s	Function that regulates the interval between unlocking and automatic relocking of doors	30 s, 60 s or 120 s	Main body ECU (Multiplex network body ECU)
      Wireless Buzzer Resp*3	ON	Wireless door lock buzzer response/ON or OFF	ON or OFF	Main body ECU (Multiplex network body ECU)
      P/W Ope buzzer*4	ON	Wireless power window buzzer response/ON or OFF	ON or OFF	Main body ECU (Multiplex network body ECU)
      Wireless Buzzer Vol*4	Level7	Wireless door lock buzzer volume	Level7, Level6, Level5, Level4, Level3, Level2, Level1 or Level0	Main body ECU (Multiplex network body ECU)

      
      

      • *1: for G.C.C. countries, Australia and New Zealand

      • *2: except G.C.C. countries, Australia and New Zealand

      • *3: except Europe and China

      • *4: except China

2. Customizing with the combination meter assembly

   Tech Tips

   
   

   • Press and hold DISP switch (steering pad switch assembly) when entering an item.

   • Briefly press DISP switch (steering pad switch assembly) when selecting an item.

   
   

   1. Turn the power switch on (IG).

   2. Enter the following menus: Settings / Vehicle Settings.

   3. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      REMOTE 2-PRESS UNLOCK	ON*1 OFF*2	Function that unlocks the driver door when the unlock switch on the electrical key transmitter is pressed once, and unlocks all doors when pressed twice. If the setting is OFF, pressing the unlock switch once makes all doors unlock.	ON or OFF	Main body ECU (Multiplex network body ECU)
      AUTO. RELOCK TIME ADJUSTMENT	30 s	Function that regulates the interval between unlocking and automatic relocking of doors.	30 s, 60 s or 120 s	Main body ECU (Multiplex network body ECU)
      LOCK/UNLOCK ANSWER BACK	ON	When the doors are locked by wireless operation, the hazard warning lights flash once. When the doors are unlocked by wireless operation, the hazard warning lights flash twice.	ON or OFF	Main body ECU (Multiplex network body ECU)
      LOCK FEEDBACK VOLUME*3	7	Wireless door lock buzzer volume	0, 1, 2, 3, 4, 5, 6 or 7	Main body ECU (Multiplex network body ECU)

      
      

      • *1: for G.C.C. countries, Australia and New Zealand

      • *2: except G.C.C. countries, Australia and New Zealand

      • *3: except China

   4. Press and hold DISP switch (steering pad switch assembly).

   5. The setting completion screen will be displayed.

   6. Return to the item selection screen.

CUSTOMIZE ENTRY AND START SYSTEM (for Entry Function)

CUSTOMIZE ENTRY AND START SYSTEM (for Start Function)

1. Customizing with the intelligent tester

   
   

   1. Connect the intelligent tester to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the intelligent tester on.

   4. Body / Entry&Start / Utility / Customize / Entry&Start or Warning

   5. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      Auto Entry Cancel SW	OFF	Function that enables or disables the entry and start system.	ON or OFF	Certification ECU (smart key ECU assembly)
      Ignition Available Area (Entry ignition available area)	All	Function that sets the area that the key must be in before the power switch can be operated.	Front or All	Certification ECU (smart key ECU assembly)
      Key Low Battery Warning (Warn when key battery becomes weak)	ON	Enables or disables the sounding of the buzzer when the key battery is low and the power switch is turned off after being on (IG) for 20 minutes or more.	ON or OFF	Certification ECU (smart key ECU assembly)

2. Customizing with the Combination meter assembly

   Tech Tips

   
   

   • Press and hold the DISP (steering pad switch assembly) when entering an item.

   • Briefly press the DISP (steering pad switch assembly) when selecting an item.

   
   

   1. Turn the power switch on (IG).

   2. Enter the following menus: Settings / Vehicle Settings.

   3. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      ENTRY AND START SYSTEM	ON	Function that enables or disables the entry and start system.	ON or OFF	Certification ECU (smart key ECU assembly)

   4. Press and hold the DISP (steering pad switch assembly).

   5. The setting completion screen will be displayed.

   6. Return to the item selection screen.

3. Entry cancel function (manual operation)

   Note

   Because the key (for card type) does not have a wireless transmitter function, it cannot be used to change the entry unlock mode.

   Tech Tips

   While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the key against the power switch.

   
   

   1. The following functions are disabled when the entry and start system is canceled.

      
      

      1. Entry unlock/lock functions

      2. Push-button start function

      3. Key lock-in prevention function

      4. Entry warning functions

   2. When canceling the system through manual operation:

      
      

      1. Make sure the following conditions are met:

      
      

      • The power switch is off.

      • The driver door is closed.

      • The driver door is unlocked.

      2. Press the unlock button of the key.

      3. Open the driver door within 5 seconds of completing the step above (driver door: closed at beginning of step → opened).

      4. With the driver door open, press the unlock button of the key 2 times within 5 seconds of completing the step above.

         Note

         If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

      5. Close and open the driver door twice within 30 seconds of completing the above step (driver door: open at beginning of step → closed → opened → closed → opened).

      6. With the driver door open, press the unlock button of the key 2 times within 30 seconds of completing the step above.

         Note

         If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

      7. Close and open the driver door within 30 seconds of completing the step above (driver door: open at beginning of step → closed → opened).

      8. Close the driver door within 5 seconds of completing the above step.

      9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the entry and start system has been canceled.

   3. Perform the following procedure to restore the entry and start system to the active state from the canceled state.

      
      

      1. Perform the procedures to cancel the entry and start system again.

      2. Check that the wireless buzzer sounds once (short beep) to confirm that the entry and start system has been restored to the active state.

         Tech Tips

         
         

         • The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.

         • The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.

CUSTOMIZE PUSH-BUTTON START SYSTEM

1. Customizing with the intelligent tester

   
   

   1. Connect the intelligent tester to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the intelligent tester on.

   4. Enter the following menus: Body / Entry&Start / Utility / Customize / Entry&Start or Warning.

   5. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      Auto Entry Cancel SW	OFF	Function that enables or disables the push-button start system.	ON or OFF	Certification ECU (smart key ECU assembly)
      Ignition Available Area (Entry ignition available area)	All	Function that sets the area that the key must be in before the power switch can be operated.	Front or All
      Key Low Battery Warning (Warn when key battery becomes weak)	ON	Enables or disables the sounding of the buzzer when the key battery is low and the power switch is turned off after being on (IG) for 20 minutes or more.	ON or OFF

2. Customizing with the Combination meter assembly

   Tech Tips

   
   

   • Press and hold DISP (steering pad switch assembly) when entering an item.

   • Briefly press DISP (steering pad switch assembly) when selecting an item.

   
   

   1. Turn the power switch on (IG).

   2. Enter the following menus: SETTINGS / VEHICLE SETTINGS

   3. Select the setting by referring to the table below

      Display	Default	Content	Setting	Relevant ECU
      ENTRY AND START SYSTEM	ON	Function that enables or disables the push-button start system.	ON or OFF	Certification ECU (smart key ECU assembly)

   4. Press and hold DISP (steering pad switch assembly).

   5. The setting completion screen will be displayed.

   6. Return to the item selection screen.

3. Push-button start cancel function (manual operation)

   Tech Tips

   While the push-button start system is canceled, the push-button start system can be operated by holding the key against the power switch.

   
   

   1. The following functions are disabled when the push-button start system is canceled.

      
      

      1. Push-button start function

      2. Key lock-in prevention function

      3. Push-button start warning functions

   2. When canceling the system through manual operation:

      
      

      1. Make sure the following conditions are met:

      
      

      • The power switch is off.

      • The driver door is closed.

      • The driver door is unlocked.

      2. Press the unlock button of the key.

      3. Open the driver door within 5 seconds of completing the step above (driver door: closed at beginning of step → opened).

      4. With the driver door open, press the unlock button of the key 2 times within 5 seconds of completing the step above.

         Note

         If the driver door is closed before or while pressing the unlock button, the push-button start cancel setting mode will end.

      5. Close and open the driver door twice within 30 seconds of completing the step above (driver door: open at beginning of step → closed → opened → closed → opened).

      6. With the driver door open, press the unlock button of the key 2 times within 30 seconds of completing the step above.

         Note

         If the driver door is closed before or while pressing the unlock button, the push-button start cancel setting mode will end.

      7. Close and open the driver door within 30 seconds of completing the step above (driver door: open at beginning of step → closed → opened)

      8. Close the driver door within 5 seconds of completing the step above.

      9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the push-button start system has been canceled.

   3. Perform the following procedure to restore the push-button start system to the active state from the canceled state.

      
      

      1. Perform the procedures to cancel the push-button start system again.

      2. Check that the wireless buzzer sounds once (short beep) to confirm that the push-button start system has been restored to the active state.

         Tech Tips

         
         

         • The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.

         • The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.

CUSTOMIZE THEFT DETERRENT SYSTEM

1. Customizing with the intelligent tester

   
   

   1. Connect the intelligent tester to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the intelligent tester on.

   4. Enter the following menus: Body / Main Body / Utility / Customize / Security

   5. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      Panic Function*1	ON	This function operates the theft deterrent system when the panic switch is pressed and held for 0.8 seconds.	ON or OFF	Main Body ECU (Multiplex Network Body ECU)
      Security control with mechanism key*2	OFF	This function set to be able to release security alarm with the mechanism key	ON or OFF
      Intrusion Win Opened	NORMAL	This function sets the sensitivity of the intrusion sensor when a door window is open.	NORMAL or SENS

      
      

      • *1: w/ Panic Switch

      • *2: w/ Airbag Cut Off Switch

CUSTOMIZE LIGHTING SYSTEM (INT)

1. Customizing with the intelligent tester

   Tech Tips

   The following items can be customized.

   Note

   
   

   • When the customer requests a change in a function, first make sure that the function can be customized.

   • Be sure to make a note of the current settings before customizing.

   • When troubleshooting a function, first make sure that the function is set to the default setting.

   
   

   1. Connect the intelligent tester to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the intelligent tester on.

   4. Enter the following menus: Body / Main Body / Utility / Customize / Illuminated Entry.

   5. Select the setting by referring to the table below.

      Illuminated Entry

      Tester Display	Default	Content	Setting	Relevant ECU
      Lighting Time	15 s	Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or IG).)	7.5 s, 15 s or 30 s	Main body ECU (Multiplex network body ECU)
      I/L when ACC OFF	ON	Lights up the power switch illumination, front interior lights and rear interior light when the power switch is turned from on (ACC or IG) to off.	ON or OFF
      I/L ON W/Door Key Unlock	ON	Lights up the power switch illumination, front interior lights and rear interior light when doors are unlocked using a mechanical key or door control transmitter.	ON or OFF
      Room Light when Aprchd	ON	Lights up the power switch illumination, front interior lights, rear interior light and footwell lights when a key enters any actuation area around the doors.	ON or OFF
      Inside Foot Light	ON	Lights up the footwell lights illumination.	ON or OFF
      Center Console Spot Light	ON	Lights up the center console spot light when the power switch is turned on (ACC or IG).	ON or OFF
      Light Control	ON	Dims (ON setting) or turns off (OFF setting) the footwell lights when all of the following conditions are met: The power switch is on (IG). The shift lever is moved to select a shift state other than park (P). All doors are closed.	ON or OFF
      Interior Light Control	ON	Lights up the front interior lights, footwell lights and center console spot light when the illuminated entry function is operating.	ON or OFF

2. Customizing with the combination meter assembly

   Tech Tips

   
   

   • Press and hold the DISP switch (steering pad switch assembly) when entering an item.

   • Briefly press the DISP switch (steering pad switch assembly) when selecting an item.

   
   

   1. Turn the power switch on (IG).

   2. Enter the following menus: Settings / Vehicle Settings

   3. Select the setting by referring to the table below

      Display	Default	Content	Setting	Relevant ECU
      Int. Lights Off Adjustment	15 sec.	Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or IG).)	15 sec., 7.5 sec., 30 sec. or OFF	Main body ECU (Multiplex network body ECU)

   4. Press and hold the DISP switch (steering pad switch assembly).

   5. The setting completion screen will be displayed.

   6. Return to the item selection screen.

CUSTOMIZE METER / GAUGE SYSTEM

1. Customizing with the intelligent tester

   
   

   1. Connect the intelligent tester to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the intelligent tester on.

   4. Enter the following menus:

      
      

      1. for Warning: Customize Setting / Combination Meter / Warning.

      2. for Display: Customize Setting / Combination Meter / Display.

   5. Select the setting by referring to the table below.

      Note

      
      

      • Be sure to record the current value before customizing.

      Tech Tips

      The following items can be customized using the intelligent tester.

      Warning

      Tester Display	Default	Content	Setting	Relevant ECU
      Driver Side Seatbelt Warning Buzzer*1	ON	Function to turn on/off the seat belt warning buzzer	ON or OFF	Combination meter assembly
      Front Passenger Side Seatbelt Warning Buzzer*1	ON	Function to turn on/off the seat belt warning buzzer	ON or OFF	Combination meter assembly
      Rear Seatbelt Warning Buzzer*2	ON	Function to turn on/off the rear seat belt warning buzzer	ON or OFF	Combination meter assembly
      Reverse Buzzer	Continual	Function to change the type of the reverse warning buzzer	Single or Continual	Combination meter assembly

      
      

      • *1: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more

      • *2: w/ Rear Seat Belt Warning

2. Customizing with the combination meter assembly

   Tech Tips

   
   

   • Press and hold the DISP switch (steering pad switch assembly) when entering an item.

   • Briefly pressed the DISP switch (steering pad switch assembly) when selecting an item.

   
   

   1. Turn the power switch on (IG).

   2. Select the following menus: SETTINGS / METER SETTING.

   3. Select the setting by referring to the table below.

      Note

      
      

      • Be sure to record the current value before customizing.

      Tech Tips

      The following items can be customized operating the combination meter assembly.

      Meter Setting

      Tester Display	Default	Content	Setting	Relevant ECU
      TACHO METER	AUTO	Function to change the tachometer setting	AUTO, KEEP ON, OFF	Combination meter assembly
      ECO LAMP	ECO DRIVE SUPPORT	Function to change the illumination level	ECO DRIVE SUPPORT, KEEP ON, OFF	Combination meter assembly
      SPORT LAMP	AUTO	Function to change the sport illumination	AUTO, OFF	Combination meter assembly
      LAMP BRIGHTNESS	STANDARD	Function to change the illumination light	BRIGHT, STANDARD	Combination meter assembly
      EV INDICATOR	AUTO	Function to change the EV indicator setting	AUTO, OFF	Combination meter assembly
      LANGUAGE	ENGLISH	Function to change the multi-information display language	ENGLISH, FRENCH, SPANISH	Combination meter assembly
      UNITS	KM (L/1100KM) or MILES (MPG)*1	Function to change the multi-information display unit	KM (KM/L), KM (L/100KM), MILES (MPG)	Combination meter assembly

      
      

      • *1: The default setting is changed according to the vehicle specification

   4. Press and hold DISP switch (steering pad switch assembly).

   5. The setting completion screen will be displayed.

   6. Return to the item selection screen.

CUSTOMIZE SEAT BELT WARNING SYSTEM

1. Customizing with the intelligent tester

   
   

   1. Connect the intelligent tester to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the intelligent tester on.

   4. Enter the following menus: Body / Combination Meter / Utility / Customize / Warning.

   5. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      Driver Side Seatbelt Warning Buzzer	ON	Function to sound the driver seat belt warning buzzer	ON/OFF	Combination meter assembly
      Front Passenger Side Seatbelt Warning Buzzer	ON	Function to sound the front passenger seat belt warning buzzer	ON/OFF
      Rear Seatbelt Warning Buzzer*	ON	Function to sound the rear seat belt warning buzzer	ON/OFF

      
      

      • *: w/ Rear Seat Belt Warning

      Tech Tips

      This setting is only valid when the vehicle is driven at 20 km/h (12 mph) or more.

CUSTOMIZE AIR CONDITIONING SYSTEM

1. Customizing with the intelligent tester

   
   

   1. Connect the intelligent tester to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the intelligent tester on.

   4. Enter the following menus: Body / Air Conditioner / Utility / Customize.

   5. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      Set Temperature Shift	Normal	Function to control with the shifted temperature against the displayed temperature	+2 C, +1 C, Normal, -1 C or -2 C	Air conditioning amplifier assembly
      Compressor Mode	Automatic	Function to automatically turn the A/C on by pressing the AUTO button when blower is on and the A/C is off	Manual or Automatic	Air conditioning amplifier assembly
      Air Inlet Mode	Automatic	Function to shift from INLET mode to RECIRCULATION mode when the A/C is turned on	Manual or Automatic	Air conditioning amplifier assembly
      Foot/DEF Auto Mode	ON	Function to automatically turn the airflow from FOOT/DEF on when AUTO mode is on	OFF or ON	Air conditioning amplifier assembly
      Foot/DEF Automatic Blow Up Function	ON	Function to automatically increase the blower level when the defroster is on	OFF or ON	Air conditioning amplifier assembly
      Ambient Temperature Shift	Normal	Function to control the shifted ambient temperature in relation to the displayed ambient temperature	+3 C, +2 C, +1 C, Normal, -1 C, -2 C or -3 C	Air conditioning amplifier assembly
      ECO MODE Cancel	OFF	Function to cancel the ECO mode drive when item is on	OFF or ON	Air conditioning amplifier assembly
      Noise and Vibration Reduction	OFF	Function to change speed of the compressor when item is on	OFF or ON	Air conditioning amplifier assembly

2. Customizing with the combination meter assembly

   Tech Tips

   
   

   • Press and hold DISP switch (steering pad switch assembly) when entering an item.

   • Briefly press DISP switch (steering pad switch assembly) when selecting an item.

   
   

   1. Turn the power switch on (IG).

   2. Enter the following menus: Settings / Vehicle Settings.

   3. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      Auto A/C Mode	Automatic	Function to shift from INLET mode to RECIRCULATION mode when the A/C is turned on	Manual or Automatic	Air conditioning amplifier assembly

   4. Press and hold DISP switch (steering pad switch assembly).

   5. The setting completion screen will be displayed.

   6. Return to the item selection screen.

CUSTOMIZE POWER WINDOW CONTROL SYSTEM

1. Customizing with the intelligent tester

   
   

   1. Connect the intelligent tester to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the intelligent tester on.

   4. Enter the following menus: Body / Main Body / Utility / Customize / Power Window.

   5. Select the setting by referring to the table below.

      Power Window

      Tester Display	Default	Content	Setting	Relevant ECU
      Door Key P/W Up	OFF	This function is used to close the windows by operating the mechanical key.	ON/OFF	Main body ECU (Multiplex network body ECU)
      Door Key P/W Down	OFF	This function is used to open the windows by operating the mechanical key.	ON/OFF	Main body ECU (Multiplex network body ECU)
      P/W Up w/ Transmitter	OFF	This function is used to close the windows using the wireless key transmitter.	ON/OFF	Main body ECU (Multiplex network body ECU)
      P/W Down w/ Transmitter	OFF	This function is used to open the windows using the wireless key transmitter.	ON/OFF	Main body ECU (Multiplex network body ECU)
      P Window Auto Up	Avail	This function is used to enable or disable the auto up function for the front passenger door window using the power window regulator switch assembly (for front passenger side).	Avail/Not Avl	Power window ECU (Power window regulator motor assembly)
      P Window Auto Up From Driver	Avail	This function is used to enable or disable the remote auto up function for the front passenger door window using the multiplex network master switch assembly.	Avail/Not Avl	Power window ECU (Power window regulator motor assembly)
      RR Window Auto Up	Avail	This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear RH side).	Avail/Not Avl	Power window ECU (Power window regulator motor assembly)
      RR Window Auto Up From Driver	Avail	This function is used to enable or disable the remote auto up function for the rear RH door window using the multiplex network master switch assembly.	Avail/Not Avl	Power window ECU (Power window regulator motor assembly)
      RL Window Auto Up	Avail	This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear LH side).	Avail/Not Avl	Power window ECU (Power window regulator motor assembly)
      RL Window Auto Up From Driver	Avail	This function is used to enable or disable the remote auto up function for the rear LH door window using the multiplex network master switch assembly.	Avail/Not Avl	Power window ECU (Power window regulator motor assembly)

CUSTOMIZE LIGHTING SYSTEM (EXT)

1. Customizing with the intelligent tester

   
   

   1. Connect the intelligent tester to the DLC3.

   2. Turn the power switch to on (IG).

   3. Turn the intelligent tester on.

   4. Enter the following menus:

      
      

      1. for Illuminated Entry: Body / Main Body / Utility / Customize / Illuminated Entry.

      2. for Light Control: Body / Main Body / Utility / Customize / Light Control.

   5. Select the setting by referring to the table below.

      Illuminated Entry

      Display	Default	Content	Setting	Relevant ECU
      Mirr-Foot-Lgt Approached	ON	Lights up the door mirror foot lights when a key enters any actuation area around the doors.	ON or OFF	Main Body ECU (Multiplex Network Body ECU)
      Mirr-Foot-Lgt Unlocked	ON	Lights up the door mirror foot lights when doors are unlocked using a mechanical key or door control transmitter.	ON or OFF
      Mirr-Foot-Lgt w/Master SW	ON	Lights up the door mirror foot lights when the driver side door control switch on the multiplex network master switch assembly is pushed to the unlock position. Lights up the door mirror foot lights when the front passenger side door control switch on the power window regulator switch assembly is pushed to the unlock position.	ON or OFF
      Mirror Foot Lighting Time	15 s	Changes the lighting time of the door mirror foot lights.	7.5 s, 15 s, 30 s or 0 s*1
      Exterior Light Control	ON	Changes the door mirror foot light control.	ON or OFF

      
      

      • *1: Even if "0 s" is selected, it can not be set.

      Light Control

      Display	Default	Content	Setting	Relevant ECU
      Response Time*1	Normal	Changes the delay timing of lighting the taillights when going into a tunnel when the light control switch is in the AUTO position	Normal or Long	Main Body ECU (Multiplex Network Body ECU)
      Sensitivity	Normal	Adjusts the sensitivity of the automatic light control system.	Light2, Light1, Normal, Dark1 or Dark2
      DRL Function*2	ON	ON/OFF of the DRL function	ON or OFF
      Disp Ex ON Sen	Normal	Changes the ambient brightness level required to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock.	Light2, Light1, Normal, Dark1 or Dark2
      Disp Ex OFF Sen	Normal	Changes the ambient brightness level required to cancel the dimming of the lights such as the indicator lights of the combination meter, A/C indicator light and clock.	Light2, Light1, Normal, Dark1 or Dark2

      
      

      • *1: w/o Light Reminder

      • *2: w/ DRL

2. Customizing with the Combination meter assembly

   Tech Tips

   
   

   • Press and hold DISP (steering pad switch) when entering an item.

   • Briefly press DISP (steering pad switch) when selecting an item.

   
   

   1. Turn the power switch on (IG).

   2. Enter the following menus: SETTINGS / VEHICLE SETTINGS.

   3. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      LIGHT SENSOR SENSITIVITY	0 (Standard)	Adjusts the sensitivity of the automatic light control system.*2	-2, -1, 0, 1 or 2	Main Body ECU (Multiplex Network Body ECU)
      DAYTIME RUNNING LIGHTS*1	ON	ON/OFF of the DRL function	ON or OFF
      EXTERIOR LIGHTS OFF TIME ADJUSTMENT	15 s	Changes the lighting time of the door mirror foot lights.	7.5 s, 15 s, 30 s or OFF*3

      
      

      • *1: w/ DRL

      • *2: The higher the setting value is, the more the lights come on easily.

      • *3: Even if "OFF" is selected, it can not be set.