HYBRID CONTROL SYSTEM, Diagnostic DTC:P3107-213

DTC Code DTC Name
P3107-213 Airbag ECU Communication Circuit Malfunction

DESCRIPTION


DTC No. INF Code DTC Detection Condition Trouble Area
P3107 213 Short to GND in the communication circuit

  • Wire harness or connector

  • Airbag sensor assembly

  • Power management control ECU

WIRING DIAGRAM

A003VXWE11

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK DTC OUTPUT (SRS AIRBAG)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Body / SRS Airbag / DTC.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      Airbag system DTCs are not output. A
      Airbag system DTCs are output. B

    5. Turn the power switch off.


    B

    GO TO DTC CHART (AIRBAG SYSTEM) Click here

    A

  2. CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)


    1. Connect an oscilloscope between the airbag sensor assembly terminals specified in the table below.

    2. Turn the power switch on (READY).

    3. Measure the waveform.

      A003XIWE02
      Text in Illustration
      *a

      Component with harness connected

      (Airbag Sensor Assembly (w/ Rear Pretensioner))

      		 *b

      Component with harness connected

      (Airbag Sensor Assembly (w/o Rear Pretensioner))
      Item Contents
      Terminal H84-14 (GSW2) - H84-25 (E1)
      Equipment Setting 5V/DIV., 500ms/DIV.
      Condition Power switch on (READY)
      Result
      Result Proceed to
      The waveform appears as shown in the illustration. A
      The waveform differs from the one shown in the illustration. B

    4. Turn the power switch off.


    B

    CHECK AIRBAG SENSOR ASSEMBLY Click here

    A

  3. CLEAR DTC


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / DTC.

    4. Clear DTCs and freeze frame data.


    NEXT

  4. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / DTC.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      DTC P3107-213 is not output. A
      DTC P3107-213 is output. B

    5. Turn the power switch off.


    B

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

    A

  5. CHECK FOR INTERMITTENT PROBLEMS


    1. Check for intermittent problems Click here.


    NG

    REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

    OK

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

  6. CHECK AIRBAG SENSOR ASSEMBLY


    1. Disconnect connector H84 from the airbag sensor assembly.

    2. A003Y36E02
      Text in Illustration
      *a

      Component without harness connected

      (Airbag Sensor Assembly (w/ Rear Pretensioner))
      *b

      Component without harness connected

      (Airbag Sensor Assembly (w/o Rear Pretensioner))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H84-14 (GSW2) - H84-25 (E1) Power switch off 10 kΩ or higher

    3. Connect the airbag sensor assembly connector.


    NG

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    OK

  7. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AIRBAG SENSOR ASSEMBLY)


    1. Disconnect connector H3 from the power management control ECU.

    2. Disconnect connector H84 from the airbag sensor assembly.

    3. Measure the resistance according to the value(s) in the table below.

      A003YCXE02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Power Management Control ECU)

      		 *b

      Rear view of wire harness connector

      (to Airbag Sensor Assembly (w/ Rear Pretensioner))
      *c

      Rear view of wire harness connector

      (to Airbag Sensor Assembly (w/o Rear Pretensioner))

      		 - -
      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H3-29 (ABFS) or H84-14 (GSW2) - Body ground and other terminals Power switch off 10 kΩ or higher

    4. Connect the airbag sensor assembly connector.

    5. Connect the power management control ECU connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE POWER MANAGEMENT CONTROL ECU Click here