CYLINDER HEAD REASSEMBLY


  1. INSTALL SPARK PLUG TUBE

    Note

    When using a new cylinder head, the spark plug tubes must be replaced.


    1. A003SNFE05

      Apply adhesive onto the shaded area of a new spark plug tube.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
      Standard application width
      1.0 to 3.0 mm (0.0394 to 0.118 in.)

      Note


      • Install the spark plug tube within 3 minutes of applying adhesive.

      • Be careful not to deform the spark plug tube.

      • Be careful not to expose the seal to coolant for at least 1 hour after installing the tube.

    2. A003UDWE04
      Text in Illustration
      *a Cylinder Head Casting Surface

      Using a wooden block and a hammer, tap in the spark plug tube to the specified protrusion height.

      Standard protrusion height
      122 mm (4.80 in.)

      Note

      To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.

  2. INSTALL STUD BOLT

    Note

    If a stud bolt is deformed or its threads are damaged, replace it.


    1. Using an E8 "TORX" socket, install the stud bolts.

      A003RFGE09
      Text in Illustration
      *a Intake Side: *b Exhaust Side:
      Torque:
      9.5 N*m  { 97 kgf*cm, 84 in.*lbf }

  3. INSTALL NO. 2 STRAIGHT SCREW PLUG

    Note

    If water leaks from the straight screw plug or the plug is corroded, replace it.


    1. A003U7U

      Using a 10 mm straight hexagon wrench, install 3 new gaskets and the 3 straight screw plugs.

      Torque:
      44 N*m  { 449 kgf*cm, 32 ft.*lbf }

  4. INSTALL VALVE SPRING SEAT


    1. Install the valve spring seats to the cylinder head.

  5. INSTALL VALVE STEM OIL SEAL


    1. A003SJRE08
      Text in Illustration
      *a Intake Side:
      *b Exhaust Side:
      *c Gray
      *d Black

      Apply a light coat of engine oil to a new oil seal.

      Note

      Pay close attention when installing the intake and exhaust oil seals. For example, installing the intake oil seal to the exhaust side or installing the exhaust oil seal to the intake side can cause installation problems later.

      Tech Tips

      The intake valve oil seal is gray and the exhaust valve oil seal is black.

    2. A003U4FE02
      Text in Illustration
      *a CORRECT
      *b INCORRECT

      Using SST, push on the oil seal.

      SST
      09201-41020

      Note

      Failure to use SST will cause the seal to be damaged or improperly seated.

  6. INSTALL INTAKE VALVE


    1. Place the cylinder head on wooden blocks.

    2. A003RKHE15

      Apply engine oil to each valve over an area 30 mm (1.18 in.) or more from its tip as shown in the illustration.

    3. Install the valve, compression spring and spring retainer to the cylinder head.

      Note

      Install the same parts in the same combination to the original locations.

    4. A003RMLE02

      Using SST, compress the spring and install the valve retainer locks.

      SST
      09202-70020   ( 09202-00010 )
    5. A003TR0

      Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

      Note


      • Be careful not to damage the valve stem tip.

      • Be careful not to damage the retainer.

  7. INSTALL EXHAUST VALVE


    1. Place the cylinder head on wooden blocks.

    2. A003TDME14

      Apply engine oil to each valve over an area 30 mm (1.18 in.) or more from its tip as shown in the illustration.

    3. Install the valve, compression spring and spring retainer to the cylinder head.

      Note

      Install the same parts in the same combination to the original locations.

    4. A003SF2E02

      Using SST, compress the spring and install the valve retainer locks.

      SST
      09202-70020   ( 09202-00010 )
    5. A003T97

      Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

      Note


      • Be careful not to damage the valve stem tip.

      • Be careful not to damage the retainer.