ENGINE ASSEMBLY INSTALLATION


  1. INSTALL FLYWHEEL SUB-ASSEMBLY


    1. Gently place the engine assembly onto wood blocks or equivalent.

      Note

      This step should be done while hanging the engine assembly using the engine hangers and a chain block.

    2. Install the flywheel sub-assembly Click here.

  2. INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY


    1. Gently place the engine assembly onto wood blocks or equivalent.

      Note

      This step should be done while hanging the engine assembly using the engine hangers and a chain block.

    2. Install the transmission input damper assembly Click here.

  3. INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY


    1. Install the hybrid vehicle transaxle assembly Click here.

      Note

      Be careful not to apply excess force to the transmission input damper assembly when removing or installing the hybrid vehicle transaxle assembly. If excess force is applied, the transmission input damper assembly may be damaged, or its splines may become misaligned.

  4. INSTALL ENGINE WIRE

  5. INSTALL FLYWHEEL HOUSING SIDE COVER


    1. Install the flywheel housing side cover.

  6. INSTALL STARTER HOLE INSULATOR


    1. Install the starter hole insulator with the 2 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  7. INSTALL RADIATOR PIPE


    1. Install the radiator pipe with the 2 bolts.

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

    2. Install the No. 3 radiator hose with the clamp.

  8. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

    Tech Tips

    Perform this procedure only when replacement of the engine mounting insulator is necessary.


    1. A003UH4E01

      Position the engine mounting insulator sub-assembly RH as shown in the illustration.

    2. Temporarily install bolt A to the engine mounting insulator sub-assembly RH.

    3. Tighten the 3 bolts to the engine mounting insulator sub-assembly RH in the order the bolt B, bolt C and bolt A.

      Torque:
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }

    4. Install the 2 cooler brackets with the 2 bolts.

      Torque:
      9.8 N*m  { 100 kgf*cm, 87 in.*lbf }

  9. INSTALL ENGINE MOUNTING INSULATOR LH

    Tech Tips

    Perform this procedure only when replacement of the engine mounting insulator is necessary.


    1. A003RSRE01

      Temporarily install bolt A to the engine mounting insulator LH.

    2. Tighten the 4 bolts to the engine mounting insulator LH in the order the bolt C, bolt B, bolt D and bolt A.

      Torque:
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }

  10. INSTALL REAR ENGINE MOUNTING INSULATOR


    1. Install the rear engine mounting insulator to the engine mounting bracket with the through bolt.

      Torque:
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }

      Tech Tips

      Perform this procedure only when replacement of the engine mounting insulator is necessary.

  11. INSTALL FRONT ENGINE MOUNTING INSULATOR


    1. A003RFF

      Temporarily install the front engine mounting insulator with the bolt and nut.

  12. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE


    1. Set the engine assembly with transaxle on the engine lifter.

      Note


      • Install a height adjustment attachment and plate lift attachment onto the engine assembly with transaxle.

      • Do not position a height adjustment attachment or plate lift attachment onto the front frame assembly.

      Tech Tips

      Place the engine on wooden blocks or equivalent so that the engine is level.

    2. Remove the 2 bolts and 2 engine hangers.

    3. Set the engine assembly with transaxle and front suspension crossmember on the engine lifter.

    4. Operate the engine lifter and lift the engine assembly with transaxle and front suspension crossmember to the position where the engine mounting insulators RH and LH can be installed.

      CAUTION:

      Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.

      Note


      • Make sure that the engine is clear of all wiring and hoses.

      • While raising the engine into the vehicle, do not allow it to contact the vehicle.

    5. Install the front crossmember with the 4 bolts.

      Torque:
      99 N*m  { 1010 kgf*cm, 73 ft.*lbf }
    6. A003U7O

      Install the front engine mounting insulator to the front crossmember with the 2 bolts.

      Torque:
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }

    7. Install the engine mounting insulator LH with the through bolt and nut.

      Torque:
      56 N*m  { 571 kgf*cm, 41 ft.*lbf }

      Note

      When installing the engine mounting insulator, tighten the nut while holding the bolt.

    8. A003UE0E01

      Install the engine mounting insulator RH with the bolt and 2 nuts.

      Torque:
      Nut A
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }
      Nut B
      52 N*m  { 530 kgf*cm, 38 ft.*lbf }
      Bolt
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }
    9. A003TWK

      Tighten the front engine mounting insulator with the bolt and nut.

      Torque:
      145 N*m  { 1479 kgf*cm, 107 ft.*lbf }

  13. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY


    1. Support the front suspension crossmember with a jack.

    2. While inserting SST into the reference holes on the front suspension crossmember RH and LH alternately, tighten the 2 bolts A, 2 bolts B and 2 nuts on the RH and LH sides to the respective specified torque in several steps.

      A003RQ9E01
      Text in Illustration
      *a Front Side
      SST
      09670-00020
      Torque:
      Bolt A
      145 N*m  { 1479 kgf*cm, 107 ft.*lbf }
      Bolt B
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }
      Nut
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }
    3. A003RJH

      Install the 2 wire harness clamp brackets with the 2 bolts.

      Torque:
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }

  14. INSTALL FRONT SUSPENSION MEMBER REAR BRACE LH


    1. A003TK4E01

      Install the front suspension member rear brace LH with the 3 bolts and clip.

      Torque:
      Bolt A
      145 N*m  { 1479 kgf*cm, 107 ft.*lbf }
      Bolt B
      93 N*m  { 948 kgf*cm, 69 ft.*lbf }

  15. INSTALL FRONT SUSPENSION MEMBER REAR BRACE RH

    Tech Tips

    Perform the same procedure as for the LH side.

  16. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH


    1. A003T4BE01

      Install the front suspension member reinforcement LH with the 4 bolts.

      Torque:
      99 N*m  { 1010 kgf*cm, 73 ft.*lbf }

      Note

      Temporarily tighten bolts A and B, and then fully tighten the 4 bolts in the order of C, B, D and A.

  17. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH


    1. A003SSIE01

      Install the front suspension member reinforcement RH with the 4 bolts.

      Torque:
      99 N*m  { 1010 kgf*cm, 73 ft.*lbf }

      Note

      Temporarily tighten bolts A and B, and then fully tighten the 4 bolts in the order of C, B, D and A.

  18. INSTALL FRONT LOWER ENGINE MOUNTING BRACKET REINFORCEMENT


    1. A003TYZ

      Install the front engine mounting bracket lower reinforcement with the 2 bolts.

      Torque:
      99 N*m  { 1010 kgf*cm, 73 ft.*lbf }

  19. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH


    1. Install a new front drive shaft hole snap ring to the front drive inboard joint assembly.

      Tech Tips

      Face the end gap of the front drive inboard joint hole snap ring downward.

  20. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING RH

    Tech Tips

    Perform the same procedure as for the LH side.

  21. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

    A003T89

    1. Coat the spline of the inboard joint shaft with transaxle fluid.

    2. Align the shaft splines and tap in the drive shaft with a brass bar and a hammer.

      Note


      • Face the end gap of the front drive shaft hole snap ring downward.

      • Do not damage the transaxle case oil seal.

      • Do not damage the inboard joint boot.

      • Make sure to center the front drive shaft assembly during installation to prevent damage to the front drive shaft hole snap ring.

  22. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  23. INSTALL FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY LH


    1. A003S48

      Connect the front No. 1 lower suspension arm sub-assembly to the front lower ball joint with the bolt and 2 nuts.

      Torque:
      89 N*m  { 908 kgf*cm, 66 ft.*lbf }

  24. INSTALL FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  25. INSTALL FRONT STABILIZER LINK ASSEMBLY LH


    1. A003TYP

      Install the front stabilizer link assembly to the front shock absorber with coil spring with the nut.

      Torque:
      74 N*m  { 755 kgf*cm, 55 ft.*lbf }

      Tech Tips

      If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.

  26. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  27. CONNECT TIE ROD END SUB-ASSEMBLY LH


    1. A003T7U

      Connect the tie rod end sub-assembly LH to the steering knuckle with the nut.

      Torque:
      49 N*m  { 500 kgf*cm, 36 ft.*lbf }

      Note

      Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.

    2. Install a new cotter pin.

  28. CONNECT TIE ROD END SUB-ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  29. INSTALL FRONT SPEED SENSOR LH


    1. A003RNI

      Install the front speed sensor and front flexible hose to the front shock absorber with the bolt and clamp.

      Torque:
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }

      Note

      Do not twist the front speed sensor when installing it.

      Tech Tips

      Install the front front flexible hose first and then the speed sensor harness bracket.

  30. INSTALL FRONT SPEED SENSOR RH

    Tech Tips

    Perform the same procedure as for the LH side.

  31. INSTALL FRONT AXLE SHAFT NUT LH


    1. A003S6B

      Using a chisel and a hammer, stake the front axle shaft nut.

  32. INSTALL FRONT AXLE SHAFT NUT RH

    Tech Tips

    Perform the same procedure as for the LH side.

  33. INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/ Exhaust Heat Recirculation System)

    Note

    When installing the water hose, ensure that the exhaust heat recirculation system is filled with coolant. Otherwise, the engine water pump assembly may be damaged.


    1. A003RI4

      Using a vernier caliper, measure the free length of the compression springs.

      Minimum (front) 41.5 mm (1.64 in.)
      Minimum (rear) 38.5 mm (1.52 in.)

      Tech Tips

      If the free length is less than minimum, replace the compression spring.

    2. Fully insert 2 new gaskets to the exhaust manifold and front exhaust pipe assembly.

    3. A003SHVE17
      Text in Illustration
      *1 Exhaust Manifold and Front Exhaust Pipe Assembly
      *2 Gasket
      *3 Wooden Block

      Using a plastic hammer and wooden block, tap in each new gasket until its surface is flush with the exhaust manifold and front exhaust pipe assembly.

      Note


      • Be careful with the installation direction of the gaskets.

      • Do not reuse the gaskets.

      • Do not damage the gaskets.

      • Do not push in the gasket by using the exhaust pipe when connecting it.

    4. Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.

    5. Install the front exhaust pipe assembly with the 4 bolts and 4 compression springs.

      Torque:
      43 N*m  { 440 kgf*cm, 32 ft.*lbf }

    6. Connect the 2 heater water hoses.

    7. A003UDL

      Connect the 3 clamps and oxygen sensor connector.

  34. INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/o Exhaust Heat Recirculation System)


    1. A003RI4

      Using a vernier caliper, measure the free length of the compression springs.

      Minimum (front) 41.5 mm (1.64 in.)
      Minimum (rear) 38.5 mm (1.52 in.)

      Tech Tips

      If the free length is less than minimum, replace the compression spring.

    2. Fully insert 2 new gaskets to the exhaust manifold and front exhaust pipe assembly.

    3. A003SHVE17
      Text in Illustration
      *1 Exhaust Manifold and Front Exhaust Pipe Assembly
      *2 Gasket
      *3 Wooden Block

      Using a plastic hammer and wooden block, tap in each new gasket until its surface is flush with the exhaust manifold and front exhaust pipe assembly.

      Note


      • Be careful with the installation direction of the gaskets.

      • Do not reuse the gaskets.

      • Do not damage the gaskets.

      • Do not push in the gasket by using the exhaust pipe when connecting it.

    4. Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.

    5. Install the front exhaust pipe assembly with the 4 bolts and 4 compression springs.

      Torque:
      43 N*m  { 440 kgf*cm, 32 ft.*lbf }

  35. INSTALL FRONT CENTER FLOOR BRACE


    1. Install the front center floor brace with the 4 bolts.

      Torque:
      51 N*m  { 520 kgf*cm, 38 ft.*lbf }

  36. INSTALL NO. 2 ENGINE UNDER COVER


    1. Install the No. 2 engine under cover with the 4 clips.

  37. CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    1. A003SGAE01
      Text in Illustration
      *1 Clip A
      *2 Clip B
      *a Lip

      Place clip A as shown in the illustration and engage clip B to the body to connect the No. 1 steering column hole cover sub-assembly.

      Note

      Make sure that the lips of the No. 1 steering column hole cover sub-assembly are not damaged.

  38. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


    1. A003UASE02
      Text in Illustration
      *1 Matchmark

      Align the matchmarks on the No. 2 steering intermediate shaft assembly and the steering intermediate shaft assembly.

    2. Install the bolt.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

  39. INSTALL COLUMN HOLE COVER SILENCER SHEET


    1. Install the column hole cover silencer sheet with the 2 clips.

    2. Install the floor carpet.

  40. INSTALL WIRE HARNESS


    1. Connect the wire harness with the 2 clamps.

    2. Connect the wire harness with the 2 clamps.

    3. A003TJ2

      Connect the wire harness to the engine room junction block.

    4. Connect the 2 connectors to the engine room junction block.

    5. A003RTF

      Connect the connector to the ECM with the 2 clamps and lock lever.

  41. INSTALL ELECTRIC INVERTER COMPRESSOR


    1. Temporarily install the electric inverter compressor with the 3 bolts.

    2. A003TJQE01

      Install the electric inverter compressor with the 3 bolts.

      Torque:
      25 N*m  { 250 kgf*cm, 18 ft.*lbf }

      Note

      Tighten the bolts in the order shown in the illustration to install the electric inverter compressor.

    3. A003TLSE01

      Engage each clamp.

    4. Connect the connector <A> and lock the green-colored lock as shown in the illustration.

      CAUTION:

      Wear insulated gloves when performing the procedures.

      Text in Illustration
      *1 Green-colored Lock

    5. Connect the connector <B>.

  42. CONNECT FUEL TUBE SUB-ASSEMBLY


    1. Connect the fuel tube connector and fuel pipe.

      CAUTION:

      Align the fuel tube connector with the pipe, then push the fuel tube connector in until the retainer makes a "click" sound. If the connection is tight, apply a small amount of engine oil to the tip of the pipe. After connecting, pull the pipe and connector to make sure that they are securely connected.

    2. A003TIR

      Engage the claw and install the No. 1 fuel pipe clamp.

  43. CONNECT NO. 1 FUEL VAPOR FEED HOSE


    1. A003UC1E01
      Text in Illustration
      *1 FR
      *2 RH

      Connect the No. 1 fuel vapor feed hose with the clamp.

      Tech Tips

      Make sure that the claws on the clamp are positioned as shown in the illustration.

  44. CONNECT HEATER HOSE


    1. Connect the heater hose with the clamp.

  45. CONNECT INLET HEATER WATER HOSE


    1. Connect the inlet heater water hose with the clamp.

  46. CONNECT OUTLET HEATER WATER HOSE


    1. Connect the outlet heater water hose with the clamp.

  47. CONNECT NO. 5 INVERTER COOLING HOSE


    1. Connect the No. 5 inverter cooling hose with the clamp.

  48. CONNECT NO. 3 INVERTER COOLING HOSE


    1. Connect the No. 3 inverter cooling hose with the clamp.

  49. CONNECT NO. 4 WATER BY-PASS HOSE


    1. Connect the No. 4 water by-pass hose with the clamp.

  50. CONNECT NO. 2 RADIATOR HOSE


    1. Connect the No. 2 radiator hose with the clamp.

  51. CONNECT NO. 1 RADIATOR HOSE


    1. Connect the No. 1 radiator hose with the clamp.

  52. INSTALL INVERTER TRAY BRACKET


    1. A003TTDE01

      Position the inverter tray bracket as shown in the illustration.

    2. Temporarily install bolt B to the inverter tray bracket.

    3. Tighten the 5 bolts to the inverter tray bracket in the order bolt A, bolt C, bolt D, bolt E and bolt B.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

    4. Connect the 2 clamps to the inverter tray bracket.

  53. INSTALL INVERTER RESERVE TANK ASSEMBLY


    1. A003U7RE01

      Temporarily install bolt A to the inverter reserve tank assembly.

    2. Tighten the 2 bolts to the inverter reserve tank assembly in the order bolt B and bolt A.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  54. INSTALL INVERTER WITH CONVERTER ASSEMBLY

    CAUTION:

    Wear insulating gloves.


    1. Temporarily install the inverter with converter assembly with the 3 bolts.

      Note


      • Since the inverter with converter assembly is very heavy, 2 people are needed to install the inverter with converter assembly. When installing the inverter with converter assembly, do not damage the parts around it.

      • To prevent damage, do not hold the inverter with converter assembly by the connectors.

      • To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.

    2. A003T4SE02

      Tighten the bolt A.

      Torque:
      12 N*m  { 122 kgf*cm, 8 ft.*lbf }

    3. Tighten the 2 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 8 ft.*lbf }

  55. CONNECT WATER HOSE


    1. A003T2GE01

      Connect the water hose to the inverter with converter assembly and lock the hose with the retainer.

      Note


      • Insert the retainer until a click sound is heard.

      • Pull on the hose to confirm that the hose is securely connected.

      • If there is foreign matter on the union or the O-ring, clean it with water and finger scouring.

    2. A003UZSE01

      Connect the water hose to the inverter with converter assembly and lock the hose with the retainer.

      Note


      • Insert the retainer until a click sound is heard.

      • Pull on the hose to confirm that the hose is securely connected.

      • If there is foreign matter on the union or the O-ring, clean it with water and finger scouring.

  56. CONNECT NO. 2 ENGINE ROOM WIRE


    1. Disconnect the No. 2 engine room wire from the protector.

    2. Connect the No. 2 engine room wire with the bolt and 2 claws.

      Torque:
      8.3 N*m  { 85 kgf*cm, 73 in.*lbf }

      Note

      Pass the No. 2 engine room wire under the two cooling hoses that pass beside the inverter.

    3. Install the No. 1 relay block cover and 2 clamps.

    4. Install the relay block cover.

  57. REMOVE INVERTER TERMINAL COVER

    CAUTION:

    Wear insulating gloves.


    1. A003UIY

      Remove the 9 bolts and inverter terminal cover.

      Note

      Make sure to pull the inverter terminal cover straight up, as a connector is connected to the bottom of the cover.

  58. CONNECT NO. 2 ENGINE WIRE

    CAUTION:

    Wear insulating gloves.

    Note

    Do not allow any foreign objects or water to enter the inverter with converter assembly.


    1. Temporarily install the No. 2 engine wire (high voltage cables of the air conditioning) and 4 bolts to the inverter assembly by hand.

    2. A003V0OE01

      Fully tighten the 4 bolts.

      Torque:
      Bolt A
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
      Bolt B
      9.2 N*m  { 94 kgf*cm, 81 in.*lbf }

      Note

      Be sure to use a torque wrench to tighten the bolts.

    3. Connect the harness clamp.

  59. CONNECT HIGH VOLTAGE CABLE OF FRONT TRANSAXLE

    CAUTION:

    Wear insulating gloves.

    Note

    Do not allow any foreign objects or water to enter the inverter with converter assembly.


    1. Temporarily install the high voltage cable of the motor (MG2) and 5 bolts to the inverter assembly by hand.

    2. A003T9ZE01

      Fully tighten the 5 bolts.

      Torque:
      Bolt A
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
      Bolt B
      9.2 N*m  { 94 kgf*cm, 81 in.*lbf }

      Note

      Be sure to use a torque wrench to tighten the bolts.

    3. Connect the harness clamp.

    4. Temporarily install the high voltage cable of the generator (MG1) and 5 bolts to the inverter assembly by hand.

    5. A003S2IE01

      Fully tighten the 5 bolts.

      Torque:
      Bolt A
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
      Bolt B
      9.2 N*m  { 94 kgf*cm, 81 in.*lbf }

      Note

      Be sure to use a torque wrench to tighten the bolts.

    6. A003TOVE01
      Text in Illustration
      *1 Align Mark

      Install the cable and cover.

      Note

      Close the cover so that the matchmarks are not visible.

  60. CONNECT FRAME WIRE

    CAUTION:

    Wear insulating gloves.

    Note


    • Make sure that the interlock is fully engaged.

    • Do not allow any foreign objects or water to enter the inverter with converter assembly.


    1. A003V0LE01
      Text in Illustration
      *1 Front view of frame wire connector
      *2 Interlock
      *3 High voltage cables of the hybrid battery

      Temporarily install the frame wire (high voltage cables of the hybrid battery) and 4 bolts to the inverter assembly by hand.

    2. Fully tighten the 4 bolts.

      Torque:
      Bolt A
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
      Bolt B
      9.2 N*m  { 94 kgf*cm, 81 in.*lbf }

      Note


      • Be sure to use a torque wrench to tighten the bolts.

      • Make sure that the interlock are fully engaged.

    3. Connect the harness clamp.

  61. CHECK HIGH VOLTAGE CABLE CONNECTION

    CAUTION:

    Wear insulating gloves.

    Note

    Do not allow any foreign objects or water to enter the inverter with converter assembly.


    1. A003RXC

      Check that each connector and terminal is firmly installed.

      Note

      Make sure that the bolts are fully tightened.

  62. INSTALL INVERTER TERMINAL COVER

    CAUTION:

    Wear insulating gloves.

    Note


    • Make sure that the interlock is fully engaged.

    • Do not allow any foreign objects or water to enter the inverter with converter assembly.


    1. A003RRSE01
      Text in Illustration
      *1 Interlock

      Install the inverter terminal cover with the 9 bolts to the inverter with converter assembly.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

  63. CONNECT ENGINE ROOM MAIN WIRE

    Note


    • Make sure that the connectors are fully engaged.

    • Do not allow any foreign objects or water to enter the inverter with converter assembly.


    1. Install the bolt, clamp and clip, and connect the engine room main wire.

      Torque:
      8.3 N*m  { 85 kgf*cm, 73 in.*lbf }

    2. Install the bolt.

      Torque:
      8.3 N*m  { 85 kgf*cm, 73 in.*lbf }
    3. A003SZ8

      Connect the engine wire to the engine room main wire.

    4. A003SZV

      Connect the connector to the inverter with converter assembly and lock the connector with the lock lever.

  64. INSTALL NO. 1 INVERTER BRACKET


    1. A003USVE01

      Temporarily install the No. 1 inverter bracket with the 3 bolts.

    2. Tighten the 3 bolts in the order shown in the illustration.

      Torque:
      14 N*m  { 138 kgf*cm, 10 ft.*lbf }

  65. INSTALL AIR CLEANER HOSE ASSEMBLY


    1. Install the air cleaner hose assembly and lock the hose clamp.

    2. Connect the ventilation hose.

  66. INSTALL AIR CLEANER CASE


    1. Install the air cleaner case with the 3 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    2. Connect the No. 4 water by-pass hose to the air cleaner case with the 3 clamps.

    3. Install the air cleaner filter element.

  67. INSTALL INLET AIR CLEANER ASSEMBLY


    1. Install the inlet air cleaner assembly with the 3 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    2. Connect the No. 4 water by-pass hose to the inlet air cleaner assembly with the clamp.

  68. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    1. Install the air cleaner cap sub-assembly with the 2 clamps and hose band.

    2. Connect the air flow meter connector.

  69. INSTALL SERVICE PLUG GRIP

    CAUTION:

    Wear insulating gloves.

    Note

    Before connecting the service plug, check that no parts and tools remain and that the high voltage terminals and connectors are connected securely.


    1. Wear insulated gloves and install the service plug grip in the order shown in the illustration.

      A003UES

    2. Rotate the handle of the service plug grip 90° toward the battery and slide it in the direction shown by the arrow until a click sound is heard.

  70. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  71. INSTALL BATTERY BOX COVER


    1. Engage the 3 guides to install the battery box cover.

  72. INSTALL REAR DECK FLOOR BOX


    1. Install the rear deck floor box.

  73. INSTALL REAR FLOOR MAT


    1. Install the rear floor mat.

  74. ADD HYBRID TRANSAXLE FLUID


    1. A003SS2E01
      Text in Illustration
      *1 Filler nozzle

      Add transaxle fluid until the fluid level is between 0 to 10 mm (0 to 0.394 in.) from the bottom lip of the filler plug opening.

      Note


      • Stop the vehicle on a level surface.

      • Recheck the transaxle fluid level after driving following fluid replacement.

      • Insufficient or excessive amounts of transaxle fluid may damage the hybrid transaxle.

      • Be sure to add fluid slowly. If fluid is added quickly, the fluid may hit internal parts and bounce back, resulting in fluid coming out of the filler plug opening.

      • Be sure to fully insert the filler nozzle into the filler plug opening.

      Reference
      3.4 liters (3.6 US qts, 3.0 lmp.qts)
      Fluid Type
      Toyota Genuine ATF WS

  75. INSPECT HYBRID TRANSAXLE FLUID


    1. A003UXW

      After adding fluid, leave it for 30 seconds so that the fluid surface can become still again, and then check that the fluid level is between 0 to 10 mm (0 to 0.394 in.) from the bottom lip of the filler plug opening. (If the fluid is insufficient, return to the Add Hybrid Transaxle Fluid procedure.)

      Note


      • Stop the vehicle on a level surface.

      • Recheck the transaxle fluid level after driving following fluid replacement.

      • Insufficient or excessive amounts of transaxle fluid may damage the hybrid transaxle.

      • Be sure to add fluid slowly. If fluid is added quickly, the fluid may hit internal parts and bounce back, resulting in fluid coming out of the filler plug opening.

      • Be sure to directly check that the transaxle fluid level is within the specified range.

    2. Check for leaks if the quantity of transaxle fluid is low.

    3. Using a 10 mm hexagon socket wrench, install the filler plug with a new gasket.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

  76. ADD COOLANT (for Engine)


    1. Tighten the radiator drain cock plug.

    2. Connect the hose to the air release valve. (w/ Air Release Valve)

    3. Loosen the air release valve. (w/ Air Release Valve)

    4. Add TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank filler opening until coolant overflows from the air release valve. Then tighten the air release valve. (w/ Air Release Valve)

    5. Disconnect the hose from the air release valve. (w/ Air Release Valve)

    6. A003TGQE01
      Text in Illustration
      *1 B Line

      Add TOYOTA Super Long Life Coolant (SLLC) to the B line on the reservoir tank.

      Standard Capacity
      Item Capacity
      Engine coolant

      w/ Exhaust Heat Recirculation System:

      7.2 liters (7.6 US qts, 6.3 lmp. qts)

      w/o Exhaust Heat Recirculation System:

      6.5 liters (6.8 US qts, 5.7 lmp. qts)

      Tech Tips

      TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

      Note

      Never use water as a substitute for engine coolant.

    7. Squeeze the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.

      If the coolant level is low, add coolant.

    8. Put the engine in inspection mode Click here.

    9. Install the reservoir tank cap.

    10. Bleed air from the cooling system.

      Note


      • Before starting the engine, turn the A/C switch off.

      • Adjust the heater control to the maximum hot setting.

      • Adjust the blower speed to the low setting.


      1. Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.

        Tech Tips

        The thermostat opening timing can be confirmed by squeezing the inlet radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the hose.

        CAUTION:

        When squeezing the radiator hose:

        • Wear protective gloves.

        • Be careful as the radiator hoses are hot.

        • Keep your hands away from the radiator fan.

      2. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air from the system.

        CAUTION:

        When squeezing the radiator hose:

        • Wear protective gloves.

        • Be careful as the radiator hoses are hot.

        • Keep your hands away from the radiator fan.

    11. A003TGQE02
      Text in Illustration
      *1 Full Line
      *2 Low Line

      After the engine has cooled down, check that the coolant level is between full and low lines.

      If the coolant level is low, add coolant to the full line on the reservoir tank.

  77. ADD COOLANT (for Inverter)

    Note


    • Do not reuse the drained coolant because it may contain foreign objects.

    • If the vehicle is driven with air in the inverter cooling system, damage may occur and the following DTCs may be set.

      DTC No. Detection Item
      P0A01-726 Motor Electronics Coolant Temperature Sensor Circuit Range / Performance
      P0A04-725 Motor Electronics Coolant Temperature Sensor Circuit Intermittent
      P0A08-264 DC / DC Converter Status Circuit
      P0A78-284 Drive Motor "A" Inverter Performance
      P0A78-286 Drive Motor "A" Inverter Performance
      P0A7A-322 Generator Inverter Performance
      P0A7A-324 Generator Inverter Performance
      P0A93-346 Inverter Cooling System Performance
      P0A94-553 DC / DC Converter Performance
      P0A94-557 DC / DC Converter Performance
      P0AEE-277 Motor Inverter Temperature Sensor "A" Circuit Range / Performance
      P0AF1-276 Drive Motor Inverter Temperature Sensor "A" Circuit Intermittent / Erratic
      P0BCD-315 Generator Inverter Temperature Sensor Circuit Range / Performance
      P0BD0-314 Generator Inverter Temperature Sensor Circuit Intermittent / Erratic
      P0C39-626 DC / DC Converter Temperature Sensor "A" Range / Performance
      P0C3C-625 DC / DC Converter Temperature Sensor "A" Intermittent / Erratic
      P0C3E-628 DC / DC Converter Temperature Sensor "B" Range / Performance
      P0C41-627 DC / DC Converter Temperature Sensor "B" Intermittent / Erratic
      P0C73-776 Motor Electronics Coolant Pump "A" Control Performance

    1. A003RO4

      Slowly pour coolant into the reserve tank until it reaches the F line.

      Coolant quantity
      2.1 liters (2.2 US qts, 1.8 Imp. qts.)

    2. When using the intelligent tester:


      1. Connect the intelligent tester to the DLC3.

      2. Turn the power switch on (IG).

      3. Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.

      4. Keep the coolant at the F line in the reserve tank to compensate for the drop in coolant level when the air bleeds.

        Standard
        Air bleeding from the inverter cooling system is completed when the noise made by the inverter water pump assembly becomes smaller and the circulation of coolant in the reserve tank improves.

        Tech Tips

        Loud noise made by the inverter water pump assembly and poor circulation of coolant in the reserve tank indicates that there is air in the cooling system.

    3. When not using the intelligent tester:


      1. Turn the power switch on (READY). [*1]

      2. Turn the power switch off and add coolant to the F line because the coolant level drops as the air bleeds. [*2]

        Note


        • Be sure to turn the power switch off before adding SLLC.

        • Do not work on the components in the engine compartment while the vehicle is in the READY-on state because the engine is in intermittent operation.

      3. Repeat steps [*1] and [*2] until air bleeding from the cooling system is completed.

        Standard
        Air bleeding from the inverter cooling system is completed when the noise made by the inverter water pump assembly becomes smaller and the circulation of coolant in the reserve tank improves.

        Tech Tips

        Loud noise made by the inverter water pump assembly and poor circulation of coolant in the reserve tank indicates that there is air in the cooling system.

    4. After the air is completely bled from the cooling system, tighten the reserve tank cap.

    5. A003RO4

      Add coolant to the F line of the reserve tank.

  78. ADD ENGINE OIL


    1. Add new engine oil and install the oil filler cap.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)

      • API grade SL "Energy-Conserving".


      • SM "Energy-Conserving" or ILSAC multigrade engine oil

      • 0W-20


      • 5W-20


      • 5W-30


      • 10W-30
      API grade SL or SM multigrade engine oil

      • 15W-40


      • 20W-50
      Standard Capacity
      Item Standard Condition
      Drain and refill with oil filter change 4.2 liters (4.4 US qts, 3.7 lmp. qts)
      Drain and refill without oil filter change 3.9 liters (4.1 US qts, 3.4 lmp. qts)
      Dry fill 4.7 liters (5.0 US qts, 4.1 lmp. qts)

  79. INSPECT ENGINE OIL LEVEL


    1. Put the engine in inspection mode Click here.

    2. Warm up and stop the engine, then wait for 5 minutes. The oil level should be between the low level and full level marks on the engine oil level dipstick. If the engine oil level is low, check for leakage and add oil up to the full level mark.

      Note

      Do not add engine oil to above the full level mark.

  80. INSPECT FOR FUEL LEAK


    1. Check fuel pump operation.


      1. Connect the intelligent tester to the DLC3.

      2. Turn the power switch on (IG).

        Note

        Do not start the engine.

      3. Turn the intelligent tester on.

      4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump /Speed.

      5. Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.

    2. Inspect for fuel leaks.


      1. Check that there is no fuel leakage after performing maintenance anywhere on the fuel system. If there is a fuel leak, repair or replace parts as necessary.

    3. Turn the power switch off.

    4. Disconnect the intelligent tester from the DLC3.

  81. INSPECT FOR COOLANT LEAK (for Engine)

    CAUTION:

    Do not remove the reservoir tank cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

    Note

    Before performing each inspection, turn the A/C switch off.


    1. Remove the reservoir tank cap.

    2. A003T8A

      Fill the radiator and reservoir with coolant, and then attach a radiator cap tester.

    3. Put the engine in inspection mode Click here.

    4. Warm up the engine.

    5. Using a radiator cap tester, increase the pressure inside the radiator to 108 kPa (1.1 kgf/cm2, 16 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator, front exhaust pipe assembly and the heater hose around and engine water pump assembly for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.

    6. Remove the radiator cap tester.

    7. Install the reservoir tank cap.

  82. INSPECT FOR COOLANT LEAK (for Inverter)


    1. Remove the reserve tank cap.

      CAUTION:

      To avoid the danger of being burned, do not remove the reserve tank cap while the coolant for the inverter is still hot.

    2. A003SWR

      Install the radiator cap tester.

    3. Pump the radiator cap tester to 122 kPa (1.2 kgf/ cm2, 17.7 psi), and then check that the pressure does not drop.

      Tech Tips

      If the pressure drops, check the hoses, radiator, inverter water pump assembly, inverter with converter, and hybrid vehicle transaxle assembly for leaks.

    4. Reinstall the reserve tank cap.

  83. INSPECT FOR OIL LEAK

  84. INSPECT FOR EXHAUST GAS LEAK

  85. INSTALL CENTER NO. 4 ENGINE UNDER COVER

  86. INSTALL NO. 1 ENGINE UNDER COVER

  87. INSTALL ENGINE UNDER COVER

  88. INSTALL REAR ENGINE UNDER COVER LH

  89. INSTALL REAR ENGINE UNDER COVER RH

  90. INSTALL FRONT WHEELS

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  91. INSPECT IGNITION TIMING


    1. Put the engine in inspection mode Click here.

    2. Warm up and stop the engine.

    3. When using the intelligent tester:

      Check the ignition timing.


      1. Connect the intelligent tester to the DLC3.

      2. Put the engine in inspection mode Click here.

      3. Turn the intelligent tester on.

      4. Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.

        Standard ignition timing
        0 to 16 degrees BTDC

        Note


        • Check the ignition timing with the cooling fans off.

        • Turn off all electrical systems and the A/ C.

        • When checking the ignition timing, the shift position should be selected neutral (N) or park (P).

        Tech Tips

        Refer to the intelligent tester operator's manual for further details.

      5. Check that the ignition timing advances immediately when the engine speed is increased.

      6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1 / ON.

      7. Monitor IGN Advance of the Data List.

        Standard ignition timing
        8 to 12 degrees BTDC

        Note

        When checking the ignition timing, the shift position should be selected neutral (N) or park (P).

        Tech Tips

        Refer to the intelligent tester operator's manual for further details.

      8. Enter the following menus: Connect the TC and TE1 / OFF.

      9. Turn the power switch off.

      10. Turn the intelligent tester off.

      11. Disconnect the intelligent tester from the DLC3.

    4. When not using the intelligent tester:


      1. A003SMDE35
        Text in Illustration
        *1 DLC3

        Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

        SST
        09843-18040

        Note


        • Be sure to connect the terminals correctly. Failure to do this can damage the engine.

        • Check the ignition timing with the cooling fans off.

        • Turn off all electrical systems and the A/ C.

        • When checking the ignition timing, the shift position should be selected neutral (N) or park (P).

      2. Remove the No. 2 cylinder head cover Click here.

      3. A003UK3

        Pull out the wire harness shown in the illustration.

        Note

        After checking, wrap the wire harness with tape.

      4. Connect the clip of the timing light to the wire harness.

        Note

        Use a timing light that detects the primary signal.

      5. Inspect the ignition timing at idle.

        Standard ignition timing
        8 to 12 degrees BTDC

        Note

        When checking the ignition timing, the shift position should be selected neutral (N) or park (P).

        Tech Tips

        After running the engine at 1000 to 1300 rpm for 5 seconds, check that it returns to idle speed.

      6. Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

      7. Inspect the ignition timing at idle.

        Standard ignition timing
        0 to 16 degrees BTDC

      8. Confirm that the ignition timing advances when the engine rpm is increased.

      9. Remove the timing light.

      10. Install the No. 2 cylinder head cover Click here.

  92. INSPECT ENGINE IDLE SPEED


    1. Put the engine in inspection mode Click here.

    2. Warm up and stop the engine.

    3. When using the intelligent tester:


      1. Connect the intelligent tester to the DLC3.

      2. Put the engine in inspection mode Click here.

      3. Turn the intelligent tester on.

      4. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

        Tech Tips

        Refer to the intelligent tester operator's manual for further details.

      5. Inspect the engine idle speed.

        Standard idle speed
        950 to 1050 rpm

        Note


        • Turn all electrical systems and the A/C off.

        • Inspect the idle speed with the cooling fans off.

        • When checking the idle speed, the shift position should be selected neutral (N) or park (P).

      6. Turn the power switch off.

      7. Turn the intelligent tester off.

      8. Disconnect the intelligent tester from the DLC3.

    4. When not using the intelligent tester:


      1. A003RY1E04
        Text in Illustration
        *1 DLC3

        Using SST, connect a tachometer tester probe to terminal 9 (TAC) of the DLC3.

        SST
        09843-18030

      2. Put the engine in inspection mode Click here.

      3. Inspect the engine idle speed.

        Standard idle speed
        950 to 1050 rpm

        Note


        • Turn all electrical systems and the A/C off.

        • Inspect the idle speed with the cooling fans off.

        • When checking the idle speed, the shift position should be selected neutral (N) or park (P).

      4. Disconnect terminal 9 (TAC) of the DLC3.

  93. INSPECT CO/HC

    Tech Tips

    This check determines whether or not the idle CO / HC complies with regulations.


    1. Put the engine in inspection mode Click here.

    2. Warm up the engine.

    3. Run the engine at 2500 rpm for approximately 180 seconds.

    4. Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe while idling.

    5. Check the CO/HC concentration while idling and when the engine is running at 2500 rpm.

      Tech Tips

      When doing a 2 mode (with the engine idling/ running at 2500 rpm) test, the measurement procedures are determined by applicable local regulations.

      If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.


      1. Check the DTCs Click here.

      2. See the table below for possible causes, then inspect the applicable parts and repair them if necessary.

        CO HC Problem Possible Cause
        Normal High Rough idle

        1. Faulty ignition:


          • Incorrect timing

          • Fouled, shorted or improperly gapped plugs

        2. Incorrect valve clearance

        3. Leaks from intake and exhaust valves

        4. Leaks from cylinders

        5. Faulty EGR
        Low High Rough idle (Fluctuating HC reading)

        1. Vacuum leaks:


          • PCV hoses

          • Intake manifold

          • Throttle body

          • Brake booster line

        2. Lean mixture causing misfire

        3. Faulty EGR
        High High Rough idle (Black smoke from exhaust)

        1. Restricted air cleaner filter element

        2. Plugged PCV valve

        3. Faulty EFI systems:


          • Faulty pressure regulator

          • Faulty engine coolant temperature sensor

          • Faulty mass air flow meter

          • Faulty ECM

          • Faulty injectors

          • Throttle body

        4. Faulty EGR

  94. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

    Click here

  95. INSTALL NO. 2 CYLINDER HEAD COVER


    1. Engage the 3 clips to install the cover.

      Note


      • Be sure to engage the clips securely.

      • Do not apply excessive force or hit the cover to engage the clips. This may cause the cover to break.

  96. INSTALL OUTER COWL TOP PANEL (for LHD)


    1. A003SJJ

      Install the outer cowl top panel with the 8 bolts and nut.

      Torque:
      Bolt
      8.8 N*m  { 90 kgf*cm, 78 in.*lbf }
      Nut
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    2. Engage the clamp.

    3. A003UBYE01
      Text in Illustration
      *1 No. 1 Heater Air Duct Splash Shield Seal
      *2 Water Guard Plate RH

      Bend the No. 1 heater air duct splash shield seal and water guard plate RH, and engage each claw.

  97. INSTALL OUTER COWL TOP PANEL (for RHD)


    1. A003UWL

      Install the outer cowl top panel with the 8 bolts and nut.

      Torque:
      Bolt
      8.8 N*m  { 90 kgf*cm, 78 in.*lbf }
      Nut
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    2. Engage the clamp of the wire harness.

    3. A003SKXE01
      Text in Illustration
      *1 Water Guard Plate RH
      *2 No. 1 Heater Air Duct Splash Shield Seal

      Bend the water guard plate RH and No. 1 heater air duct splash shield seal, and engage each claw.

  98. INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for LHD)


    1. A003TIT

      Install the cowl body mounting reinforcement LH with the 3 bolts.

      Torque:
      8.8 N*m  { 90 kgf*cm, 78 in.*lbf }

  99. INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for RHD)


    1. A003TW0

      Install the cowl body mounting reinforcement LH with the 3 bolts.

      Torque:
      8.8 N*m  { 90 kgf*cm, 73 in.*lbf }

  100. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    1. A003TALE01

      Install the windshield wiper motor and link assembly with the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    2. Connect the connector.

  101. INSTALL COWL TOP VENTILATOR LOUVER LH


    1. A003TAO

      Engage the clip and 6 claws, and install the cowl top ventilator louver LH.

  102. INSTALL COWL TOP VENTILATOR LOUVER RH


    1. A003U85

      Engage the clip and 11 claws, and install the cowl top ventilator louver RH.

  103. INSTALL HOOD TO COWL TOP SEAL


    1. Engage the 7 clips and install the hood to cowl top seal.

  104. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

    2. A003SZUE12
      Text in Illustration
      *1 Wiper Arm Serration
      *2 Wire Brush
      *3 Wiper Pivot Serration

      When reusing the front wiper arm and blade assembly RH:


      1. Clean the wiper arm serrations.

    3. When reusing the windshield wiper link assembly:


      1. Clean the wiper pivot serrations with a wire brush.

    4. A003U1SE02
      Text in Illustration
      *1 Louver Edge
      *2 Ceramic Notch

      Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

      Torque:
      26 N*m  { 265 kgf*cm, 19 ft.*lbf }

      Tech Tips

      Hold the arm hinge by hand to fasten the nut.

      Area Measurement
      A 17.5 to 32.5 mm (0.69 to 1.28 in.)

  105. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

    2. A003SZUE12
      Text in Illustration
      *1 Wiper Arm Serration
      *2 Wire Brush
      *3 Wiper Pivot Serration

      When reusing the front wiper arm and blade assembly LH:


      1. Clean the wiper arm serrations.

    3. When reusing the windshield wiper link assembly:


      1. Clean the wiper pivot serrations with a wire brush.

    4. A003TK0E02
      Text in Illustration
      *1 Louver Edge
      *2 Ceramic Notch

      Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

      Torque:
      26 N*m  { 265 kgf*cm, 19 ft.*lbf }

      Tech Tips

      Hold the arm hinge by hand to fasten the nut.

      Area Measurement
      A 25.5 to 40.5 mm (1.00 to 1.59 in.)

    5. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.

  106. INSTALL FRONT WIPER ARM HEAD CAP


    1. Install the 2 front wiper arm head caps.

  107. CHECK ABS SPEED SENSOR SIGNAL

    Click here