SFI SYSTEM Fuel Pump Control Circuit

DESCRIPTION

When the NE signal is input to the ECM, Tr is turned on, current flows to the coil of the C/OPN (circuit opening) relay, the relay switches on, power is supplied to the fuel pump and the fuel pump operates.

While the NE signal is generated (engine running), the ECM keeps Tr on (C/OPN relay on) and the fuel pump also keeps operating.

A003UA5E01

WIRING DIAGRAM

A003TTIE01

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

    5. Check whether the fuel pump operation sound occurs when performing the Active Test on the tester.

      OK
      Fuel pump operating sound occurs.

    NG

    INSPECT NO. 2 INTEGRATION RELAY (C/OPN RELAY) Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  2. INSPECT NO. 2 INTEGRATION RELAY (C/OPN RELAY)


    1. A003RV8E19
      Text in Illustration
      *a

      Component without harness connected

      (No. 2 Integration Relay)

      Remove the No. 2 integration relay from the engine room relay block.

    2. Disconnect the No. 2 integration relay connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1B-4 - 1B-8 Battery voltage is not applied to terminals 1B-6 and 1B-7 10 kΩ or higher
      Battery voltage is applied to terminals 1B-6 and 1B-7 Below 1 Ω

    4. Reconnect the No. 2 integration relay connector.

    5. Reinstall the No. 2 integration relay.


    NG

    REPLACE NO. 2 INTEGRATION RELAY Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY (C/OPN RELAY) - ECM)


    1. Disconnect the ECM connector.

    2. Remove the No. 2 integration relay from the engine room relay block.

    3. Disconnect the No. 2 integration relay connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      1B-7 - A50-8 (FC) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      1B-7 or A50-8 (FC) - Body ground Always 10 kΩ or higher

    5. Reconnect the ECM connector.

    6. Reconnect the No. 2 integration relay connector.

    7. Reinstall the No. 2 integration relay.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 INTEGRATION RELAY (C/OPN RELAY) - ECM)

    OK

  4. CHECK HARNESS AND CONNECTOR (C/OPN RELAY - IG2 RELAY)


    1. Remove the No. 2 integration relay from the engine room relay block.

    2. Disconnect the No. 2 integration relay connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      1A-4 - 1B-6 Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      1A-4 or 1B-6 - Body ground Always 10 kΩ or higher

    4. Reconnect the No. 2 integration relay connector.

    5. Reinstall the No. 2 integration relay.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (C/OPN RELAY - IG2 RELAY)

    OK

  5. CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY (C/OPN RELAY) - FUEL PUMP)


    1. Disconnect the fuel pump connector.

    2. Remove the No. 2 integration relay from the engine room relay block.

    3. Disconnect the No. 2 integration relay connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      1B-8 - L17-4 Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      1B-8 or L17-4 - Body ground Always 10 kΩ or higher

    5. Reconnect the fuel pump connector.

    6. Reconnect the No. 2 integration relay connector.

    7. Reinstall the No. 2 integration relay.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 INTEGRATION RELAY (C/OPN RELAY) - FUEL PUMP)

    OK

  6. CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)


    1. Disconnect the fuel pump connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      L17-5 - Body ground Always Below 1 Ω

    3. Reconnect the fuel pump connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL PUMP - BODY GROUND)

    OK

  7. INSPECT FUEL PUMP


    1. Inspect the fuel pump Click here.


    NG

    REPLACE FUEL PUMP Click here

    OK

  8. CHECK ECM POWER SOURCE CIRCUIT


    1. Check the ECM power source circuit Click here.


    NG

    REPAIR OR REPLACE ECM POWER SOURCE CIRCUIT

    OK

    REPLACE ECM Click here