CAMSHAFT REMOVAL


  1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

    Click here

  2. INSTALL ENGINE STAND


    1. Install the engine onto an engine stand with the bolts.

  3. REMOVE ENGINE HANGERS


    1. A003RGQ

      Remove the 2 bolts and 2 engine hangers.

  4. REMOVE THROTTLE BODY ASSEMBLY


    1. A003S9R

      Disconnect the throttle body connector and the 2 water by-pass hoses.

    2. Remove the 2 bolts, 2 nuts and throttle body assembly.

    3. A003S6R

      Remove the gasket from the intake manifold.

  5. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


    1. Remove the engine oil level dipstick.

    2. A003UU4

      Remove the 2 bolts, clamp and engine oil level dipstick guide.

    3. Remove the O-ring from the engine oil level dipstick guide.

  6. REMOVE EGR PIPE ASSEMBLY


    1. A003SHC

      Disconnect the 2 wire harness clamps.

    2. A003U8S

      Remove the bolt and wire harness support.

    3. A003TVM

      Remove the 4 bolts, EGR pipe assembly and 2 gaskets.

  7. REMOVE EGR VALVE ASSEMBLY


    1. A003SPT

      Disconnect the connector, wire harness clamp and 4 water hoses.

    2. A003TUGE01
      Text in Illustration
      *1 Stud Bolt and Nut

      Remove the 4 nuts and bolt.

    3. Using an E8 "TORX" wrench, remove the 4 stud bolts and EGR valve with cooler assembly.

    4. Remove the gasket.

    5. A003SJV

      Remove the 2 nuts, EGR valve assembly and gasket.

  8. REMOVE EGR WITH COOLER PIPE SUB-ASSEMBLY


    1. A003SPT

      Disconnect the connector, wire harness clamp and 4 water hoses.

    2. A003TUGE01
      Text in Illustration
      *1 Stud Bolt and Nut

      Remove the 4 nuts and bolt.

    3. Using an E8 "TORX" wrench, remove the 4 stud bolts and EGR valve with cooler assembly.

    4. Remove the gasket.

    5. A003RQ1

      Remove the 2 nuts, EGR cooler sub-assembly and gasket.

  9. REMOVE INTAKE MANIFOLD


    1. A003SBT

      Disconnect the 3 connectors and 2 wire harness clamps.

    2. Remove the engine oil level dipstick.

    3. A003SLW

      Disconnect the wire harness clamp, and then remove the 2 bolts and engine oil level dipstick guide sub-assembly.

    4. Remove the O-ring from the engine oil level dipstick guide sub-assembly.

    5. A003TLT

      Disconnect the fuel vapor feed hose and ventilation hose.

    6. A003RNA

      Remove the 2 bolts, 2 nuts and intake manifold.

    7. Remove the No. 1 intake manifold to head gasket.

  10. REMOVE FUEL VAPOR FEED PIPE


    1. A003UUQ

      Remove the bolt and fuel vapor feed pipe.

  11. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


    1. A003TVP

      Remove the bolt.

    2. A003U2J

      Remove the 2 bolts and the fuel delivery pipe sub-assembly.

      Note

      Be careful not to drop the fuel injectors when removing the fuel delivery pipe.

  12. REMOVE NO. 1 DELIVERY PIPE SPACER


    1. A003U9V

      Remove the 2 No. 1 delivery pipe spacers from the cylinder head.

  13. REMOVE FUEL INJECTOR ASSEMBLY


    1. A003RM7

      Pull the 4 fuel injector assemblies out of the fuel delivery pipe sub-assembly.

    2. Remove the O-ring from each fuel injector assembly.

    3. For reinstallation, attach a tag or label to each injector shaft.

      Note

      Prevent entry of foreign objects by covering the fuel injectors with plastic bags.

    4. A003RIE

      Remove the 4 injector vibration insulators.

  14. REMOVE IGNITION COIL ASSEMBLY


    1. A003SYS

      Disconnect the 4 ignition coil connectors.

    2. Remove the 4 bolts and 4 ignition coils.

      Note

      When removing each ignition coil, do not damage the plug cap on the engine head cover opening or the upper edge of the spark plug tube.

  15. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    1. A003T4D

      Remove the 13 bolts, seal washer and cylinder head cover.

      Note

      As the gasket may stick to the cylinder head cover, be careful not to drop any of the gaskets into the engine when removing the cylinder head cover.

    2. A003SIL

      Remove the 2 gaskets from the camshaft bearing cap.

  16. REMOVE CYLINDER HEAD COVER GASKET


    1. A003SP7

      Remove the cylinder head cover gasket.

  17. REMOVE SPARK PLUG TUBE GASKET


    1. A003S5U

      Pry up the 4 claws of the ventilation baffle plate.

      Note

      Do not deform the claws of the baffle plate more than necessary.

    2. Remove the 4 gaskets from the cylinder head cover.

      Tech Tips

      Prevent the plug tube gaskets from being deformed as much as possible. The removed gaskets will be used when installing new gaskets.

      Note

      Be careful not to damage the cylinder head cover.

  18. SET NO. 1 CYLINDER TO TDC/COMPRESSION


    1. A003U7LE01
      Text in Illustration
      *1 Timing Mark
      *2 Timing Notch
      *3 Timing Mark (Rectangle)
      *4 Mark (Circle)

      Turn the crankshaft pulley until its notch and timing mark "0" of the timing chain cover are aligned.

      Tech Tips

      There are 3 marks on the camshaft timing sprocket. Make sure that the timing mark (rectangle) is at the top.

    2. Check that the timing marks on both the camshaft timing sprocket and the camshaft timing gear are facing upward as shown in the illustration.

      If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.

  19. REMOVE CRANKSHAFT PULLEY


    1. A003RYZE02
      Text in Illustration
      *a Hold
      *b Turn

      Using SST, hold the pulley in place and loosen the pulley bolt.

      SST
      09213-58014   ( 91551-80840 )
      09330-00021
    2. A003SPME02
      Text in Illustration
      *a Hold
      *b Turn

      Using SST, remove the crankshaft pulley and pulley bolt.

      SST
      09950-50013   ( 09951-05010, 09952-05010, 09953-05020, 09954-05021 )

      Tech Tips

      If necessary, remove the pulley and pulley bolt using SST.

  20. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY


    1. A003ULU

      Remove the 2 nuts, bracket, chain tensioner and gasket.

      Note

      Do not turn the crankshaft without the No. 1 chain tensioner installed.

  21. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    1. A003S62

      Remove the 3 bolts and engine mounting bracket RH.

    2. A003UPM

      Remove the 4 bolts and oil filter bracket.

    3. A003SRR

      Remove the 2 O-rings.

    4. A003S9QE01
      Text in Illustration
      *1 Seal Washer

      Remove the 18 bolts and seal washer.

    5. A003S4IE01
      Text in Illustration
      *1 Protective Tape

      Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

      Note


      • Be careful not to damage the contact surfaces of the timing chain cover, cylinder block, and cylinder head.

      • Pry the timing chain cover out evenly in order to prevent damaging the knock pins.

      Tech Tips

      Tape the screwdriver tip before use.

    6. A003T74

      Remove the 3 O-rings.

  22. REMOVE TIMING CHAIN COVER OIL SEAL


    1. Place the timing chain cover on wooden blocks.

    2. A003UZIE01
      Text in Illustration
      *1 Protective Tape
      *2 Wooden Block

      Using a screwdriver and a hammer, knock out the oil seal.

      Tech Tips

      Tape the screwdriver tip before use.

      Note

      Do not damage the surface of the oil seal press fit hole.

  23. REMOVE CHAIN TENSIONER SLIPPER


    1. A003RRO

      Remove the chain tensioner slipper from the cylinder block.

  24. REMOVE NO. 1 CHAIN VIBRATION DAMPER


    1. A003TMA

      Remove the 2 bolts and chain vibration damper.

  25. REMOVE NO. 2 CHAIN VIBRATION DAMPER


    1. A003RMW

      Remove the 2 bolts and No. 2 chain vibration damper.

  26. REMOVE CHAIN SUB-ASSEMBLY


    1. A003UT2

      Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear counterclockwise to loosen the chain between the camshaft timing gears.

    2. With the chain loosened, release the chain from the camshaft timing gear and place it on the camshaft timing gear.

      Tech Tips

      Be sure to release the chain from the sprocket completely.

    3. Turn the camshaft clockwise to return it to the original position and remove the chain.

  27. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY


    1. Inspect the lock of the camshaft timing gear.

    2. A003UZ5E02
      Text in Illustration
      *1 Adhesive Tape
      *a Adhesive Tape Sealing Area
      *b Prick a Hole

      After cleaning and degreasing the VVT oil hole on the intake side of the No. 1 camshaft bearing cap, completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.

      Note

      Be sure to cover the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.

    3. Prick a hole in the tape covering the oil hole as shown in the illustration. (Procedure A)

    4. A003SPC

      Apply approximately 150 kPa (1.5 kgf/cm2, 22 psi) of air pressure to the hole pricked in procedure A to release the lock pin.

      Note


      • If air leaks out, reattach the adhesive tape.

      • Cover the oil hole with a piece of cloth when applying air pressure to prevent oil from spraying.

    5. Forcibly turn the camshaft timing gear in the advance direction (counterclockwise).

      Tech Tips

      Depending on the air pressure applied, the camshaft timing gear may turn in the advance direction without assistance.

    6. A003UDJ

      Turn the camshaft timing gear within its movable range (26.5 to 28.5°) 2 or 3 times without turning it to the most retarded position. Make sure that the camshaft timing gear turns smoothly.

    7. Remove the adhesive tape from the No. 1 camshaft bearing cap.

  28. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY


    1. A003TDE
      Text in Illustration
      *1 Flange Bolt
      *a Do not remove

      Remove the flange bolt while holding the hexagonal portion of the camshaft with a wrench, and then remove the camshaft timing gear.

      Note


      • Before removing the camshaft timing gear, make sure that the lock pin has been released.

      • A003TM7E04

        Be sure not to remove the other 4 bolts.

      • Keep the camshaft timing gear horizontal while removing it from the camshaft.

  29. REMOVE CAMSHAFT TIMING SPROCKET


    1. A003S0T

      Remove the flange bolt while holding the hexagonal portion of the camshaft with a wrench, and then remove the camshaft timing sprocket.

  30. REMOVE CAMSHAFT BEARING CAP


    1. A003UX2E01

      Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.

    2. A003UOSE01

      Uniformly loosen and remove the 15 bearing cap bolts in the sequence shown in the illustration.

      Note

      Uniformly loosen the bearing cap bolts while keeping the camshaft housing level.

    3. Remove the 5 bearing caps.

      Tech Tips

      Arrange the removed parts in the correct order.

  31. REMOVE CAMSHAFT


    1. A003TTQ

      Remove the camshaft.

  32. REMOVE NO. 2 CAMSHAFT


    1. A003RF9

      Remove the No. 2 camshaft.

  33. REMOVE NO. 1 CAMSHAFT BEARING


    1. A003RU3

      Remove the 2 No. 1 camshaft bearings.

  34. REMOVE NO. 2 CAMSHAFT BEARING


    1. A003RTN

      Remove the 2 No. 2 camshaft bearings.

  35. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY


    1. A003SIU

      Remove the 2 bolts.

    2. A003SP1E02
      Text in Illustration
      *1 Protective Tape

      Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

      Note

      Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.

      Tech Tips

      Tape the screwdriver tip before use.