AUDIO AND VISUAL SYSTEM Illumination Circuit

DESCRIPTION

Power is supplied to illuminate the radio receiver assembly and steering pad switch assembly when the light control switch is in the tail or head position.

WIRING DIAGRAM

A003TXDE01

INSPECTION PROCEDURE

Note

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the supplemental restraint system Click here.

PROCEDURE


  1. CHECK ILLUMINATION


    1. Check if the illumination of the radio receiver assembly, steering pad switch assembly, glove box or others (hazard switch, etc.) comes on when the light control switch is turned to the head or tail position.

      Result
      Result Proceed to
      Illumination comes on for all components except steering pad switch assembly. A
      Illumination comes on for all components except radio receiver assembly. B
      Illumination comes on for all components except radio receiver assembly or steering pad switch assembly. C
      No illumination comes on (radio receiver assembly, hazard switch, glove box, etc.). D

    B

    CHECK HARNESS AND CONNECTOR (BATTERY - RADIO RECEIVER ASSEMBLY) Click here

    C

    CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - BODY GROUND) Click here

    D

    GO TO LIGHTING SYSTEM Click here

    A

  2. CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY)


    1. A003UALE32
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Spiral with Sensor Cable Sub-assembly)

      Disconnect the spiral with sensor cable sub-assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      E6-12 (IL+2) - Body ground Light control switch in tail or head position 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY


    1. A003UM9E35
      Text in Illustration
      *a

      Component without harness connected

      (Spiral with Sensor Cable Sub-assembly)
      *b Steering Pad Switch Assembly Side
      *c Vehicle Side

      Disconnect the steering pad switch assembly and spiral with sensor cable sub-assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      z2-8 (EAU) - E6-4 (EAU) Center Below 1 Ω
      2.5 rotations to the left
      2.5 rotations to the right
      z2-5 (IL+2) - E6-12 (IL+2) Center Below 1 Ω
      2.5 rotations to the left
      2.5 rotations to the right

      Note

      The spiral with sensor cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral with sensor cable sub-assembly may prevent the airbag from deploying. Be sure to read the pages shown in the brackets.

      Tech Tips



    NG

    REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY Click here

    OK

  4. CHECK HARNESS AND CONNECTOR


    1. Disconnect the radio receiver assembly and spiral with sensor cable sub-assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E26-6 (SWG) - E6-4 (EAU) Always Below 1 Ω
      E26-6 (SWG) - Body ground Always Below 1 Ω
      E6-4 (EAU) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT STEERING PAD SWITCH ASSEMBLY


    1. Disconnect the steering pad switch assembly connector.

    2. Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal EAU of the steering pad switch assembly connector.

      A003S23E01

    3. Check if the illumination for the steering pad switch assembly comes on.

      OK
      Illumination for the steering pad switch assembly comes on.
      Text in Illustration
      *a

      Component without harness connected

      (Steering Pad Switch Assembly)

      		 - -

    NG

    REPLACE STEERING PAD SWITCH ASSEMBLY Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  6. CHECK HARNESS AND CONNECTOR (BATTERY - RADIO RECEIVER ASSEMBLY)


    1. A003T5AE83
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Radio Receiver Assembly)

      Disconnect the radio receiver assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      E1-10 (ILL+) - Body ground Light control switch in the tail or head position 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  7. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - BODY GROUND)


    1. Disconnect the radio receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E1-7 (E) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here