SHIFT LEVER INSTALLATION


  1. INSTALL TRANSMISSION INSTRUMENT PANEL SHIFT ASSEMBLY


    1. Install the transmission instrument panel shift assembly with the 4 nuts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    2. Connect the connector and wire harness clamp to the transmission instrument panel shift assembly.

  2. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL


    1. A003UP7

      Engage the 2 clips and guide.

    2. Install the lower No. 2 instrument panel finish panel with the 2 screws <E> or <F>.

  3. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. A003TWU

      Engage the 2 clips and guide.

    2. Engage the 4 claws and 2 guides.

    3. Install the lower No. 1 instrument panel finish panel with the 2 screws <E> or <F>.

  4. INSTALL INSTRUMENT PANEL UNDER TRAY


    1. A003TDZ

      Engage the 4 claws and install the instrument panel under tray.

  5. INSTALL FRONT NO. 1 CONSOLE BOX INSERT


    1. Engage the guide.

    2. Engage the 3 claws and install the front No. 1 console box insert.

  6. INSTALL FRONT NO. 2 CONSOLE BOX INSERT


    1. Engage the guide.

    2. Engage the 3 claws and install the front No. 2 console box insert.

  7. INSTALL REAR CONSOLE BOX ASSEMBLY


    1. Engage the 4 claws.

    2. Install the rear console box assembly with the 4 bolts and 2 screws.

  8. INSTALL CONSOLE BOX CARPET


    1. Install the console box carpet.

  9. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL


    1. Engage the 4 claws and 6 clips.

    2. Install the lower center instrument panel finish panel with the 2 screws <E> or <F>.

  10. INSTALL UPPER CONSOLE PANEL


    1. Engage the 7 claws and install the upper console panel.

  11. INSTALL REAR CONSOLE BOX COVER


    1. Connect the connector.

    2. Engage the 2 guides and 4 clips to install the rear console box cover.

  12. INSTALL INSTRUMENT PANEL FINISH PANEL END LH


    1. A003SDS

      Engage the 4 clips and install the instrument panel finish panel end LH.

  13. INSTALL INSTRUMENT PANEL FINISH PANEL END RH


    1. A003ROO

      Engage the 4 clips and install the instrument panel finish panel end RH.

  14. INSTALL SHIFT LEVER KNOB


    1. Using a die (M6 x P1.00 mm), clean the threads of the transmission instrument panel shift assembly.

    2. A003U0R

      Turn the shift lever knob in the direction of the arrow in the illustration to install it.

    3. A003UEWE01
      Text in Illustration
      *1 Measuring Point

      Using a vernier caliper, adjust the height of the shift lever knob.

      Standard height
      13.6 to 16.6 mm (0.535 to 0.654 in.)

    4. Remove the protective tape around the transmission instrument panel shift assembly.

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  16. INSTALL BATTERY BOX COVER


    1. Engage the 3 guides to install the battery box cover.

  17. INSTALL REAR DECK FLOOR BOX


    1. Install the rear deck floor box.

  18. INSTALL REAR FLOOR MAT


    1. Install the rear floor mat.

  19. INSPECT SHIFT LEVER


    1. Turn the power switch on (READY).

    2. Check that all available shift positions can be selected by moving the shift lever.

      Tech Tips

      After the shift lever is replaced with a new one, perform the above operation. If this operation is not performed, moving the shift lever may not initially select shift positions.