HYBRID CONTROL SYSTEM, Diagnostic DTC:P0AFC-150

DTC Code DTC Name
P0AFC-150 Hybrid Battery Pack Sensor Module

DESCRIPTION

The power management control ECU alerts the driver and performs fail-safe control based on error signals sent from the battery smart unit.

DTC NO. INF Code DTC Detection Condition Trouble Area
P0AFC 150 Power source voltage of the battery smart unit drops during precharge.

  • Battery smart unit

  • Wire harness or connector

  • IGCT No. 2 fuse

WIRING DIAGRAM

A003ULPE01

INSPECTION PROCEDURE

CAUTION:


  • Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

  • After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work Click here.

Tech Tips


  • Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

  • After completing repairs, restart the system (turn the power switch on (READY)) and recheck for DTCs Click here.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (IGCT VOLTAGE)

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly Click here.

    3. Turn the power switch on (IG).

    4. A003RR2E07
      Text in Illustration
      *a

      Component with harness connected

      (Battery Smart Unit)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      d1-4 (IGCT) - d1-8 (GND) Power switch on (IG) 11 to 14 V

      Note

      Turning the power switch on (IG) with the service plug grip removed causes an interlock switch system DTC to be set. Use the intelligent tester to clear the DTCs Click here.

    5. Turn the power switch off.

    6. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly Click here.


    NG

    Click here

    OK

    REPLACE BATTERY SMART UNIT Click here

  2. CHECK FUSE (IGCT NO. 2)


    1. A003UPGE01
      Text in Illustration
      *1 Engine Room Junction Block Assembly
      *2 IGCT No. 2 Fuse

      Remove the IGCT No. 2 fuse from the engine room junction block assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      IGCT No. 2 fuse Always Below 1 Ω

    3. Install the IGCT No. 2 fuse to the engine room junction block assembly.


    NG

    REPLACE FUSE (IGCT NO. 2)

    OK

  3. CHECK HARNESS AND CONNECTOR (IGCT RELAY - BATTERY SMART UNIT)

    CAUTION:

    Be sure to wear insulated gloves.


    1. A003TQ4E01
      Text in Illustration
      *1 Engine Room Junction Block Assembly
      *2 IGCT Relay

      Remove the IGCT relay from the engine room junction block assembly.

    2. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    3. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly Click here.

    4. A003TSJE07

      Disconnect connector d1 from the battery smart unit.

    5. A003SBYE01
      Text in Illustration
      *1 Engine Room Junction Block Assembly
      *2 IGCT relay terminal 5
      *a

      Rear view of wire harness connector

      (to Battery Smart Unit)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      IGCT relay terminal 5 - d1-4 (IGCT) Power switch off Below 1 Ω

    6. Connect the battery smart unit connector.

    7. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly Click here.

    8. Install the IGCT relay to the engine room junction block assembly.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (BATTERY SMART UNIT - BODY GROUND)

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the No. 1 hybrid vehicle battery carrier bracket sub-assembly Click here.

    3. A003TSJE07

      Disconnect connector d1 from the battery smart unit.

    4. A003T1XE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Battery Smart Unit)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      d1-8 (GND) - Body Ground Always Below 1 Ω

    5. Connect the battery smart unit connector.

    6. Install the No. 1 hybrid vehicle battery carrier bracket sub-assembly Click here.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE BATTERY SMART UNIT Click here