FUEL LID LOCK CONTROL CABLE ASSEMBLY INSTALLATION

INSTALL SIDE DECK TRIM PANEL ASSEMBLY LH

1. Engage the 2 claws and 4 clips, and install the side deck trim panel assembly LH.

   Note

   After installation, make sure that the back door weatherstrip does not interfere with the side deck trim panel assembly LH.

INSTALL NO. 2 ROOM LIGHT ASSEMBLY

INSTALL REAR SEAT SIDE GARNISH LH

1. Engage the 6 claws and 2 clips, and install the rear seat side garnish LH.

INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY (for LH Side)

1. Install the rear seatback hinge sub-assembly with the bolt.

   Torque:

   18 N*m  { 185 kgf*cm, 13 ft.*lbf }

INSTALL REAR DECK TRIM COVER

1. Engage the 10 claws and install the rear deck trim cover.

   Note

   After installation, make sure that the back door weatherstrip does not interfere with the rear deck trim cover.

INSTALL REAR NO. 1 FLOOR BOARD

1. Engage the 2 claws, 2 clips and 3 guides.

2. Install the rear No. 1 floor board with the bolt.

INSTALL NO. 6 BATTERY CARRIER PANEL

1. 

   Text in Illustration

   *1	Double-sided tape
   *a	Installation position guide

   Using the installation position guide shown in the illustration as a base, attach a new No. 6 battery carrier panel to the rear No. 1 floor board.

2. 

   Text in Illustration

   *1	Double-sided tape

   Install the No. 6 battery carrier panel as shown in the illustration.

INSTALL DECK BOARD SUB-ASSEMBLY

1. Engage the 3 claws and 3 clips to install the deck board sub-assembly.

INSTALL DECK FLOOR BOX LH

1. Engage the 3 guides to install the deck floor box LH.

INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

1. Engage the 2 pins.

2. Connect the 2 suspenders and install the package tray trim panel assembly.

INSTALL LOWER CENTER PILLAR GARNISH LH

CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

1. Install the floor end of the front seat outer belt assembly LH with the bolt.

   Torque:

   41 N*m  { 420 kgf*cm, 30 ft.*lbf }

INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)

1. Engage the 3 claws and install the lap belt outer anchor cover.

INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

1. 

   Text in Illustration

   *1	Alignment Mark (Yellow)

   Align the alignment mark (yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

   Note

   After installation, check that the corners fit correctly.

INSTALL REAR DOOR SCUFF PLATE LH

1. Engage the 8 claws and install the rear door scuff plate LH.

INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

1. 

   Text in Illustration

   *1	Alignment Mark (Pink)

   Align the alignment mark (pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

   Note

   After installation, check that the corners fit correctly.

INSTALL COWL SIDE TRIM BOARD LH

1. Engage the guide and 2 clips, then install the cowl side trim board LH.

INSTALL FRONT DOOR SCUFF PLATE LH

1. Engage the 10 claws, then install the front door scuff plate LH.

CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH (for RHD)

1. Install the floor end of the front seat outer belt assembly RH with the bolt.

   Torque:

   41 N*m  { 420 kgf*cm, 30 ft.*lbf }

INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH (for RHD)

1. 

   Text in Illustration

   *1	Alignment Mark (White)

   Align the alignment mark (white) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

   Note

   After installation, check that the corners fit correctly.

INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for RHD)

1. 

   Text in Illustration

   *1	Alignment Mark (Blue)

   Align the alignment mark (blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

   Note

   After installation, check that the corners fit correctly.

INSTALL REAR SEAT ASSEMBLY LH

1. Place the rear seat assembly LH in the cabin.

   Note

   Be careful not to damage the vehicle body.

2. Install the rear side of the rear seat assembly LH with the 2 bolts.

   Torque:

   37 N*m  { 377 kgf*cm, 27 ft.*lbf }

3. Install the front side of the rear seat assembly LH with the 2 bolts.

   Torque:

   37 N*m  { 377 kgf*cm, 27 ft.*lbf }

INSTALL NO. 1 REAR SEAT CUSHION HINGE COVER (for LH Side)

1. Engage the 4 claws and install the No. 1 rear seat cushion hinge cover.

INSTALL NO. 2 REAR SEAT CUSHION HINGE COVER (for LH Side)

1. Engage the 4 claws and install the No. 2 rear seat cushion hinge cover.

INSTALL REAR CONSOLE BOX ASSEMBLY (for RHD)

1. Engage the 4 claws.

2. Install the rear console box assembly with the 4 bolts and 2 screws.

INSTALL CONSOLE BOX CARPET (for RHD)

1. Install the console box carpet.

INSTALL REAR CONSOLE BOX COVER (for RHD)

1. Connect the connector.

2. Engage the 2 guides and 4 clips to install the rear console box cover.

INSTALL FRONT SEAT ASSEMBLY LH

INSPECT FRONT SEAT SLIDE ADJUSTER LOCK

1. During sliding operation of the front seat, check that the left and right adjusters move together smoothly and lock simultaneously.

   If the seat adjusters do not lock simultaneously, loosen the seat fixation bolts to adjust the adjuster's position.

INSTALL INNER SEAT TRACK COVER LH

1. Engage the 2 claws and install the inner seat track cover.

INSTALL OUTER SEAT TRACK COVER LH

1. Engage the 2 claws and install the outer seat track cover.

INSPECT FRONT SEAT SLIDE ADJUSTER LOCK (for RHD)

1. During sliding operation of the front seat, check that the left and right adjusters move together smoothly and lock simultaneously.

   If the seat adjusters do not lock simultaneously, loosen the seat fixation bolts to adjust the adjuster's position.

INSTALL BATTERY BOX COVER

1. Engage the 3 guides to install the battery box cover.

INSTALL REAR DECK FLOOR BOX

1. Install the rear deck floor box.

INSTALL REAR FLOOR MAT

1. Install the rear floor mat.

INSPECT FRONT SEAT ASSEMBLY

1. w/ Seat Heater System:

   Check the seat heater operation.

   
   

   1. Turn the power switch on (IG).

   2. Push the seat heater switch ON.

   3. Wait 5 minutes or more and confirm that the seat surface becomes warm.