BACK DOOR REASSEMBLY


  1. INSTALL LICENSE PLATE LIGHT ASSEMBLY


    1. Engage the 2 claws to install the license plate light assembly.

    2. Connect the connector.

  2. INSTALL BACK DOOR OPENER SWITCH ASSEMBLY


    1. Connect the connector and install the back door opener switch assembly.

  3. INSTALL BACK DOOR OUTSIDE GARNISH


    1. A003RN1

      Install 6 new gaskets to the back door outside garnish.

    2. Engage the 2 clips and install the back door outside garnish.

    3. Install the 6 nuts.

  4. INSTALL REAR SPOILER SUB-ASSEMBLY


    1. Install the 4 new gaskets to the rear spoiler sub-assembly.

    2. Engage the 3 clips and install the rear spoiler sub-assembly.

    3. Install the 4 nuts and 2 grommets.

  5. INSTALL REAR WIPER MOTOR ASSEMBLY


    1. A003V0C

      Install the rear wiper motor assembly with the 3 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    2. Connect the connector.

  6. INSTALL REAR WIPER MOTOR GROMMET


    1. A003RZDE05
      Text in Illustration
      *1 MP grease

      Apply MP grease to the entire surface of the wiper motor grommet lip.

      Tech Tips

      Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.

    2. Install the wiper motor grommet.

  7. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY


    1. Stop the wiper motor at the automatic stop position.

    2. Clean the wiper arm serrations.

    3. When reinstalling:


      1. A003SZUE13
        Text in Illustration
        *1 Wiper Arm Serration
        *2 Wire Brush
        *3 Wiper Pivot Serration

        Clean the wiper pivot serrations with a wire brush.

    4. A003U8GE02
      Text in Illustration
      *1 Defogger Line

      Install the arm and blade with the nut. Make sure that the arm and blade comes to the position shown in the illustration.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Tech Tips


      • Hold down the arm hinge by hand while tightening the nut.

      • Install the arm and blade so that the rear wiper blade is aligned with the ceramic line.

  8. INSTALL REAR WIPER ARM HEAD CAP


    1. A003RKF

      Install the rear wiper arm head cap.

      Tech Tips

      Push down on the cap until a click sound can be heard.

    2. Operate the rear wiper while spraying washer fluid on the glass. Make sure that the rear wiper functions properly and there is no interference with the vehicle body.

  9. INSTALL BACK DOOR LOCK ASSEMBLY


    1. A003UB4

      Connect the connector.

    2. Install the back door lock assembly with the 3 bolts.

      Torque:
      13 N*m  { 133 kgf*cm, 9.6 ft.*lbf }
  10. INSTALL BACK DOOR TRIM PANEL ASSEMBLY


    1. A003T9JE01

      Engage the 11 clips and install the back door trim panel assembly.

    2. Install the clip (A).

  11. INSTALL BACK DOOR INSIDE HANDLE


    1. A003RN6

      Engage the 4 claws and install the back door inside handle.

  12. INSTALL BACK DOOR SIDE GARNISH LH


    1. A003S85

      Engage the clip and claw, and install the back door side garnish LH.

    2. A003UB6E02
      Text in Illustration
      *1 Guide

      Align the guide with the cutout, engage the 2 claws, and install the package tray trim garnish hook.

    3. A003UNV

      Engage the pin.

  13. INSTALL BACK DOOR SIDE GARNISH RH

    Tech Tips

    Use the same procedures for the RH side and the LH side.

  14. INSTALL CENTER STOP LIGHT SET


    1. Engage the 2 clips.

    2. Install the center stop light set with the 2 screws.

      Torque:
      3.2 N*m  { 33 kgf*cm, 28 in.*lbf }
    3. Connect the connector.

  15. INSTALL BACK DOOR UPPER TRIM PANEL ASSEMBLY


    1. A003S6G

      Engage the 6 clips and 4 claws, and install the back door upper trim panel assembly.