POWER WINDOW REGULATOR MOTOR (for Rear Door) INSTALLATION


  1. INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY


    1. Apply MP grease to the sliding parts of the rear door window regulator assembly

    2. Install the temporary bolt to the rear door window regulator assembly.

    3. Temporarily install the rear door window regulator assembly.

    4. Tighten the temporary bolt and 3 bolts to install the rear door window regulator assembly.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    5. Connect the connector.

  2. INSTALL REAR DOOR GLASS RUN


    1. A003TZP

      Install the rear door glass run.

  3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    1. A003TJS

      Slide the rear door glass sub-assembly to install it as shown in the illustration.

  4. INSTALL REAR DOOR QUARTER WINDOW GLASS


    1. Install the rear door quarter window glass to the rear door quarter window weatherstrip.

    2. A003SID

      Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.

  5. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    1. Insert the rear door window division bar sub-assembly from above.

    2. Install the rear door glass run to the rear door window division bar sub-assembly.

    3. A003TOO

      Install the rear door window division bar sub-assembly with the 2 bolts and screw.

  6. INSTALL REAR DOOR WEATHERSTRIP


    1. Install the rear door weatherstrip.

  7. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the rear door panel.

    2. A003SZCE02
      Text in Illustration
      *1 Reference Point

      Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.

    3. Attach the rear door service hole cover by using the reference points on the rear door panel.

      Note

      Securely install the rear door service hole cover avoiding wrinkles and air bubbles.

    4. Connect the connector.

  8. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP


    1. A003SL7

      Install the rear door inner glass weatherstrip.

  9. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A003T8I

      Connect the rear door lock remote control cable and rear door inside locking cable to the rear door inside handle sub-assembly.

    2. A003SUF

      Engage the 2 claws and install the rear door inside handle sub-assembly.

  10. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. Connect the connector.

    2. A003UCF

      Engage the rear door trim board with the 3 claws on the rear door inner glass weatherstrip.

    3. Engage the 9 clips to install the rear door trim board to the rear door panel.

    4. A003RKD

      Install the 3 screws.

  11. INSTALL DOOR ASSIST GRIP COVER


    1. A003SRH

      Engage the 4 claws and install the door assist grip cover.

  12. INSTALL REAR DOOR INSIDE HANDLE BEZEL


    1. A003SOG

      Engage the 3 claws to install the rear door inside handle bezel.

  13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  14. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here

  15. INSTALL BATTERY BOX COVER


    1. Engage the 3 guides to install the battery box cover.

  16. INSTALL REAR DECK FLOOR BOX


    1. Install the rear deck floor box.

  17. INSTALL REAR FLOOR MAT


    1. Install the rear floor mat.