POWER WINDOW CONTROL SYSTEM Rear Power Window RH does not Operate with Rear Power Window Switch RH

DESCRIPTION

When the power switch is on (IG) or on (READY), the power window regulator motor assembly (for rear RH side) is operated by the power window regulator switch assembly (for rear RH side). The power window regulator motor assembly (for rear RH side) has motor, regulator, and ECU functions.

Tech Tips

If the pulse sensor built into the power window regulator motor (for rear RH side) malfunctions, the power window control system enters fail-safe mode. The remote up/down and auto up/down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the power window regulator switch assembly (for rear RH side) at the auto up position, and opened manually by pushing down the power window regulator switch assembly (for rear RH side).

WIRING DIAGRAM

A003UEPE72

INSPECTION PROCEDURE

Note


  • The power window control system uses a multiplex communication system (LIN communication system). Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

  • When the rear door window regulator assembly (for RH side) is reinstalled or replaced, the power window control system must be initialized.

  • After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be reinitialized by repeating the following operation at least 5 times:


    1. Close the power window by fully pulling up the power window regulator switch assembly (for rear RH side) and holding it at the auto up position.

    2. Open the power window by fully pushing down the power window regulator switch assembly (for rear RH side).

  • When the ECU determines that the power window regulator motor assembly (for rear RH side) has a malfunction, DTC B2311 is stored.

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER (Main Body)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body / Data List.

    5. Read the Data List according to the display on the intelligent tester.

      Main Body (Main Body ECU (Multiplex Network Body ECU))
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Communication RR-Door Motor Connection status between power window regulator motor (for rear RH) and main body ECU (multiplex network body ECU) / OK or STOP

      OK: Normal communication

      STOP: Communication stopped

      		 -
      OK
      On the intelligent tester screen, OK is displayed.

    NG

    GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting) Click here

    OK

  2. READ VALUE USING INTELLIGENT TESTER (RR-Door Motor)


    1. Enter the following menus: Body / RR-Door Motor / Data List.

    2. Read the Data List according to the display on the intelligent tester.

      RR-Door Motor (Power Window Regulator Motor Assembly (for Rear RH Side))
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      RR Door P/W Up SW Rear RH side power window manual up switch signal / ON or OFF

      ON: Rear RH door power window manual up switch operated

      OFF: Rear RH door power window manual up switch not operated

      		 -
      RR Door P/W Down SW Rear RH side power window manual down switch signal / ON or OFF

      ON: Rear RH door power window manual down switch operated

      OFF: Rear RH door power window manual down switch not operated

      		 -
      OK
      On the intelligent tester screen, ON or OFF is displayed accordingly.

    NG

    INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH Side) Click here

    OK

  3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (RR-Door Motor)


    1. Enter the following menus: Body / RR-Door Motor / Active Test.

    2. Perform the Active Test according to the display on the intelligent tester.

      RR-Door Motor (Power Window Regulator Motor Assembly (for Rear RH Side))
      Tester Display Test Part Control Range Diagnostic Note
      Power Window Power window OFF / UP / DOWN -
      OK
      Rear RH power window operates normally.

      CAUTION:

      Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


    NG

    REPLACE REAR DOOR WINDOW REGULATOR ASSEMBLY (for RH Side) Click here

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

  4. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH Side)


    1. A003SJBE16
      Text in Illustration
      *a

      Component without harness connected

      (Power Window Regulator Switch Assembly (for Rear RH Side))

      Remove the power window regulator switch assembly (for rear RH side) Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      6 (UP) - 1 (GND) Auto up or up position Below 1 Ω
      7 (DOWN) - 1 (GND) Auto down or down position Below 1 Ω

    NG

    REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH Side) Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (REAR RH SIDE SWITCH - REAR RH SIDE MOTOR AND BODY GROUND)


    1. Disconnect the rear door window regulator assembly (for RH side) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J5-6 (UP) - J6-10 (UP) Always Below 1 Ω
      J5-7 (DOWN) - J6-7 (DOWN) Always Below 1 Ω
      J5-1 (GND) - Body ground Always Below 1 Ω
      J5-6 (UP) - Body ground Always 10 kΩ or higher
      J5-7 (DOWN) - Body ground Always 10 kΩ or higher
      J6-10 (UP) - Body ground Always 10 kΩ or higher
      J6-7 (DOWN) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE REAR DOOR WINDOW REGULATOR ASSEMBLY (for RH Side) Click here