READ DATA LIST
Tech Tips
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Sliding Roof / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Open Switch | SLIDE OPEN switch signal/ON or OFF | ON: SLIDE OPEN switch pressed OFF: SLIDE OPEN switch not pressed |
- |
| Close Switch | TILT UP switch signal/ON or OFF | ON: TILT UP switch pressed OFF: TILT UP switch not pressed |
- |
| Hall IC1 Pulse | Hall IC1 pulse output/Lo or Hi | Alternates between Lo and Hi during motor operation | Lo: Hall IC1 output is low Hi: Hall IC1 output is high |
| Hall IC1 Status | Status of Hall IC1/Normal or Error | Normal: Hall IC1 is normal Error: Hall IC1 is not normal |
- |
| Hall IC2 Pulse | Hall IC2 pulse output/Lo or Hi | Lo and Hi repeat during motor operation | Lo: Hall IC2 output is low Hi: Hall IC2 output is high |
| Hall IC2 Status | Status of Hall IC2/Normal or Error | Normal: Hall IC2 is normal Error: Hall IC2 is not normal |
- |
| Ignition (Direct Signal) | Power switch signal/ON or OFF | ON: Power switch on (IG) OFF: Power switch off |
- |
| Ignition (MPX) | Power switch signal (LIN signal)/ON or OFF | ON: Power switch on (IG) OFF: Power switch off |
- |
| Door Courtesy | Driver door courtesy light switch signal/ON or OFF | ON: Driver door open OFF: Driver door closed |
- |
| Key Off Permission | Key-off sliding roof operation permit signal/ON or OFF | ON: Front doors are not opened within 45 seconds after power switch turned off OFF: Any status except "ON" status |
- |
| Open Switch Failure(Past) | Open switch failure signal (Past)/ON or OFF | ON: Sliding roof open signal failure (Past) OFF: No sliding roof open signal failure (Past) |
- |
| Close Switch Failure(Past) | Close switch failure signal (Past)/ON or OFF | ON: Sliding roof close signal failure (Past) OFF: No sliding roof close signal failure (Past) |
- |
| Open Switch Failure(Current) | Open switch failure signal (Current)/ON or OFF | ON: Sliding roof open signal failure (Current) OFF: No sliding roof open signal failure (Current) |
- |
| Close Switch Failure(Current) | Close switch failure signal (Current)/ON or OFF | ON: Sliding roof close signal failure (Current) OFF: No sliding roof close signal failure (Current) |
- |
| Number of Trouble Codes | Number of trouble codes/Min.: 0 or Max.: 255 | Number of DTCs will be displayed | - |
PERFORM ACTIVE TEST
Tech Tips
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Sliding Roof / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Slide Roof | Operate sliding roof | Opn/Dwn / Clos/Up / OFF | - |