LOWER INSTRUMENT PANEL INSTALLATION

INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
1. Engage the 2 claws and 2 guides.
  
  Note
  
  Do not allow the wire harness to get caught in the claws.
2. Install the screw <E> or <F>.
3. Install the 2 bolts <G> or <H>.
4. Install the 10 screws <I> or <J>.
5. Engage each clamp.
6. Install the 2 screws <E> or <F>.
7. Connect each connector and install the lower instrument panel sub-assembly.
8. When using a new lower instrument panel sub-assembly:
  1. Immediately after installing the lower instrument panel sub-assembly, twist and cut off the portions shown in the illustration (joints for moulding).
9. Engage the 3 claws to install the hood lock control cable assembly.
10. Engage the 2 claws to install the DLC3.
INSTALL ANTENNA CORD SUB-ASSEMBLY (for LHD)
1. Engage the 5 clamps and install the antenna cord sub-assembly.
2. Connect the connector.
3. Install the bolt.
  
  Torque:
  
  8.4 N*m { 86 kgf*cm, 74 in.*lbf }
4. Engage the clamp.
5. Connect the connector.
INSTALL ANTENNA CORD SUB-ASSEMBLY (for RHD)
1. Engage the 4 clamps and install the antenna cord sub-assembly.
2. Connect the connector.
3. Install the bolt.
  
  Torque:
  
  8.4 N*m { 86 kgf*cm, 74 in.*lbf }
4. Engage the clamp.
5. Connect the connector.
CONNECT TRANSMISSION INSTRUMENT PANEL SHIFT ASSEMBLY
1. Install the transmission instrument panel shift assembly with the 4 nuts.
  
  Torque:
  
  12 N*m { 122 kgf*cm, 9 ft.*lbf }
2. Connect the connector and wire harness clamp to the transmission instrument panel shift assembly.
INSTALL NO. 1 SWITCH HOLE BASE
1. Connect the connectors.
2. Engage the 2 claws and 2 clips, and install the No. 1 switch hole base.
INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
1. Engage the 2 clips and guide.
2. Install the lower No. 2 instrument panel finish panel with the 2 screws <E> or <F>.
INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
1. Engage the 2 clips and guide.
2. Engage the 4 claws and 2 guides.
3. Install the lower No. 1 instrument panel finish panel with the 2 screws <E> or <F>.
INSTALL INSTRUMENT PANEL UNDER TRAY
1. Engage the 4 claws and install the instrument panel under tray.
INSTALL FRONT NO. 1 CONSOLE BOX INSERT
1. Engage the guide.
2. Engage the 3 claws and install the front No. 1 console box insert.
INSTALL FRONT NO. 2 CONSOLE BOX INSERT
1. Engage the guide.
2. Engage the 3 claws and install the front No. 2 console box insert.
INSTALL FUSE BOX OPENING COVER
1. Connect each connector.
2. Engage the 4 claws and 4 clips, to install the fuse box opening cover.
INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
1. Engage the guide.
2. Engage the 3 claws and install the instrument panel No. 2 instrument panel under cover sub-assembly.
INSTALL COWL SIDE TRIM BOARD LH
1. Engage the guide and 2 clips, then install the cowl side trim board LH.
INSTALL FRONT DOOR SCUFF PLATE LH
1. Engage the 10 claws, then install the front door scuff plate LH.
INSTALL COWL SIDE TRIM BOARD RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL FRONT DOOR SCUFF PLATE RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL REAR CONSOLE BOX ASSEMBLY
1. Engage the 4 claws.
2. Install the rear console box assembly with the 4 bolts and 2 screws.
INSTALL CONSOLE BOX CARPET
1. Install the console box carpet.
INSTALL AIR CONDITIONING CONTROL ASSEMBLY
1. Connect the connector.
2. Engage the 4 clips and install the air conditioning control assembly.
INSTALL RADIO RECEIVER OPENING COVER WITH BRACKET (w/o Radio Receiver)
1. Install the radio receiver opening cover with bracket with the 4 bolts <K>.
INSTALL RADIO AND DISPLAY RECEIVER WITH BRACKET (for Radio and Display Type)
1. Connect each connector.
2. Install the radio and display receiver with bracket with the 4 bolts.
INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (except Radio Receiver Type)
1. Engage the 4 clips and install the center instrument cluster finish panel sub-assembly.
INSTALL RADIO RECEIVER WITH BRACKET (for Radio Receiver Type)
1. Connect each connector.
2. Engage the 4 clips.
3. Install the radio receiver with bracket with the 4 bolts.
ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
1. Using pliers, expand the clamp.
2. While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.
3. Return the clamp to its original position.
4. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
INSTALL UPPER STEERING COLUMN COVER
1. Engage the 2 claws and 2 pins to install the upper steering column cover.
INSTALL LOWER STEERING COLUMN COVER
Note

If the steering column cover is installed in the incorrect order, it will not be possible to assemble the steering column cover.
1. Engage the 2 claws to temporarily install the lower steering column cover.
2. Engage the 4 claws.
3. Engage the 2 claws.
  
  Tech Tips
  
  Spread the claw and press the area around the claw to engage it.
ADJUST SPIRAL CABLE SUB-ASSEMBLY
1. Check that the power switch is off.
2. Check that the cable is disconnected from the negative (-) battery terminal.
  
  CAUTION:
  
  Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
3. Rotate the spiral cable counterclockwise slowly by hand until it feels firm.
  
  Note
  
  Do not turn the spiral cable by the airbag wire harness.
4. Text in Illustration
  
  *1 Alignment Mark
  
  Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.
  
  Note
  
  Do not turn the spiral cable by the airbag wire harness.
  
  Tech Tips
  
  The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.
INSTALL STEERING WHEEL ASSEMBLY
1. Text in Illustration
  
  *1 Matchmark
  
  Align the matchmarks on the steering wheel assembly and steering main shaft.
2. Install the steering wheel assembly set nut.
  
  Torque:
  
  50 N*m { 510 kgf*cm, 37 ft.*lbf }
3. Connect the connectors to the spiral cable sub-assembly.
INSTALL STEERING PAD
1. Check that the power switch is off.
2. Check that the cable is disconnected from the negative (-) battery terminal.
  
  CAUTION:
  
  Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
3. Connect the airbag connector to the steering pad.
  
  Note
  
  When connecting any airbag connector, take care not to damage the airbag wire harness.
4. Push in the lock to install the airbag connector.
5. Connect the horn connector to the steering pad as shown in the illustration.
6. Push the steering pad to engage the 2 hooks.
  
  Note
  
  Make sure that the hooks are securely inserted into the steering pad holes.
INSPECT STEERING WHEEL CENTER POINT
INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY
1. Check that the power switch is off.
2. Check that the cable is disconnected from the negative (-) battery terminal.
  
  CAUTION:
  
  Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
3. Connect the driver side knee airbag connector.
  
  Note
  
  When connecting any airbag connector, take care not to damage the airbag wire harness.
4. Engage the 6 claws and 2 guides.
5. Temporarily install the driver side knee airbag assembly with the 2 bolts (upper side).
6. Temporarily install the driver side knee airbag assembly with the 2 bolts (lower side).
7. Install the driver side knee airbag assembly with the 4 bolts.
  
  Torque:
  
  10 N*m { 102 kgf*cm, 7 ft.*lbf }
INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
1. Engage the guide.
2. Engage the claw.
3. Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <C> or <D>.
INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY
1. When using a new upper instrument panel sub-assembly:
  1. Immediately before installing the upper instrument panel sub-assembly, twist and cut off the portions shown in the illustration (joints for moulding).
2. When using a new upper instrument panel sub-assembly:
  1. Text in Illustration
    
    *1 Protective Tape
    
    Apply protective tape to the areas shown in the illustration.
3. Engage the 5 claws.
  Note
  - When installing the upper instrument panel sub-assembly, be careful not to damage it or the steering wheel assembly.
  - Do not allow the wire harness to get caught in the claws.
4. Engage the 3 claws and the 4 clips.
5. Install the 2 screws <C> or <D>.
6. Install the 2 passenger airbag bolts <A> or <B>.
  
  Torque:
  
  20 N*m { 204 kgf*cm, 15 ft.*lbf }
7. Connect the connector and install the upper instrument panel sub-assembly.
8. Remove the protective tape.
CONNECT INSTRUMENT PANEL WIRE ASSEMBLY
1. Check that the power switch is off.
2. Check that the cable is disconnected from the negative (-) battery terminal.
  
  CAUTION:
  
  Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
3. Connect the connector.
  
  Note
  
  When connecting any airbag connector, take care not to damage the airbag wire harness.
INSTALL NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY
1. w/ USB Audio System:
  1. Connect the connector and engage the clamp.
2. Text in Illustration
  
  *1 Protective Tape
  
  *2 Claw
  
  Apply protective tape to the area shown in the illustration.
3. Insert the instrument panel box assembly in the direction indicated by arrow (1) in the illustration so that the taped portion does not come in contact with the lower No. 1 instrument panel finish panel.
4. Push the instrument panel box assembly in the direction indicated by arrow (2) in the illustration so that the claw on the upper part of the instrument panel box assembly is inserted into the upper instrument panel sub-assembly.
5. Engage the 3 claws and 3 clips.
6. Install the No. 1 instrument panel box door sub-assembly with the 2 screws <C> or <D>.

Text in Illustration
*1	Alignment Mark

Text in Illustration
*1	Matchmark

INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

Text in Illustration

*1 Hinge

Insert the glove compartment door assembly horizontally and engage the 2 hinges.

Note

Engaging the hinges from the top will deform the hinges. Be sure to install the glove compartment door assembly horizontally.

Text in Illustration
*1	Hinge

Text in Illustration
*1	Stopper
*2	Glove Compartment Door Stopper

Bend portions (A) and (B) in the direction indicated by the arrows in the illustration to engage the 2 stoppers.

Engage the claw, connect the glove compartment door stopper, and install the glove compartment door assembly.

INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL
1. Engage the 4 claws and 6 clips.
2. Install the lower center instrument panel finish panel with the 2 screws <E> or <F>.
INSTALL UPPER CONSOLE PANEL
1. Engage the 7 claws and install the upper console panel.
INSTALL REAR CONSOLE BOX COVER
1. Connect the connector.
2. Engage the 2 guides and 4 clips to install the rear console box cover.
INSTALL FRONT PILLAR GARNISH LH
1. Remove the protective cover.
2. Text in Illustration
  
  *1 Protective Tape
  
  Make sure that the front pillar garnish clip is not damaged.
  Note
  
  If there is any damage, replace the garnish clip with a new one.
  
  When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.
3. Engage the guide.
4. Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish LH.
  
  Tech Tips
  
  Tape the tips of the needle-nosed pliers before use.
5. Engage the 2 clips to install the front pillar garnish LH.

INSTALL FRONT PILLAR GARNISH CORNER PIECE LH

Text in Illustration
*1	Protective Tape
*a	Guide (A)
*b	Guide (B)

Engage the 2 guides (B).

Engage the 2 guides (A) and 5 claws, then install the front pillar garnish corner piece LH.
Remove the protective tape.

INSTALL FRONT PILLAR GARNISH RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL FRONT PILLAR GARNISH CORNER PIECE RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY
1. Connect the connector.
2. Engage the 3 guides, 5 claws and 2 clips, and install the center instrument panel register assembly.
INSTALL INSTRUMENT PANEL FINISH PANEL END LH
1. Engage the 4 clips and install the instrument panel finish panel end LH.
INSTALL INSTRUMENT PANEL FINISH PANEL END RH
1. Engage the 4 clips and install the instrument panel finish panel end RH.
INSTALL COMBINATION METER ASSEMBLY
1. Connect the connector and temporarily install the combination meter assembly.
  
  Note
  
  When installing the combination meter assembly, do not damage the upper instrument panel sub-assembly or combination meter assembly.
2. Install the combination meter assembly with the 4 screws.
INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
1. Engage the 2 claws and 4 clips, and install the instrument cluster finish panel assembly.
2. Remove the applied protective tape on the steering column cover.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
INSTALL BATTERY BOX COVER
1. Engage the 3 guides to install the battery box cover.
INSTALL REAR DECK FLOOR BOX
1. Install the rear deck floor box.
INSTALL REAR FLOOR MAT
1. Install the rear floor mat.
INSPECT STEERING PAD
1. Make sure that the horn sounds.
  
  Tech Tips
  
  If the horn does not sound, inspect the horn system Click here.
INSPECT SRS WARNING LIGHT

Click here