ROOF HEADLINING REMOVAL


  1. REMOVE REAR FLOOR MAT


    1. A003TLX

      Remove the rear floor mat.

  2. REMOVE REAR DECK FLOOR BOX


    1. A003TAA

      Remove the rear deck floor box.

  3. REMOVE BATTERY BOX COVER


    1. A003UZD

      Disengage the 3 guides and remove the battery box cover.

  4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. Operate the tilt lever to lower the steering wheel assembly.

    2. A003SYGE02
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area shown in the illustration.

    3. A003UH7

      Disengage the 2 claws and 4 clips, and then remove the instrument cluster finish panel assembly.

  6. REMOVE COMBINATION METER ASSEMBLY


    1. A003USY

      Remove the 4 screws.

    2. A003RM0

      Pull the combination meter assembly, disconnect the connector, and remove the combination meter assembly.

      Note

      When removing the combination meter assembly, do not damage the upper instrument panel sub-assembly or combination meter assembly.

  7. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


    1. A003RXOE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. Insert a roof moulding remover and slide the remover toward the clip.

    3. A003TXA

      Pull the remover with both hands to disengage the clip as shown in the illustration.

    4. A003RUL

      Disengage the 3 clips and remove the instrument panel finish panel end LH.

  8. REMOVE INSTRUMENT PANEL FINISH PANEL END RH


    1. A003ROAE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. Insert a roof moulding remover and slide the remover toward the clip.

    3. A003TRZ

      Pull the remover with both hands to disengage the clip as shown in the illustration.

    4. A003SOQ

      Disengage the 3 clips and remove the instrument panel finish panel end RH.

  9. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A003T1DE03

      Disengage the 5 claws, 2 clips, and 3 guides.

    2. Disconnect the connector and remove the center instrument panel register assembly.

  10. REMOVE FRONT PILLAR GARNISH CORNER PIECE LH


    1. A003UQOE01
      Text in Illustration
      *1 Protective Tape
      *a Guide (A)
      *b Guide (B)

      Apply protective tape to the areas shown in the illustration.

    2. Using a screwdriver, disengage the 5 claws and 2 guides (A).

      Tech Tips

      Tape the screwdriver tip before use.

    3. Disengage the 2 guides (B) and remove the front pillar garnish corner piece LH.

  11. REMOVE FRONT PILLAR GARNISH LH


    1. A003UJZE02
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.

      Tech Tips

      Make the front pillar garnish LH hang down from the front pillar garnish clip.

    2. A003T7FE01
      Text in Illustration
      *1 Protective Tape

      Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish LH.

      Note


      • Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.

      • Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

      Tech Tips

      Tape the tips of the needle-nosed pliers before use.

    3. Disengage the guide at the front end of the front pillar garnish LH and remove it.

    4. A003TFYE02
      Text in Illustration
      *1 Protective Cover
      *2 Curtain Shield Airbag Assembly
      *3 Adhesive Tape

      Protect the curtain shield airbag assembly.

      Protective Cover Size
      X 700 mm (27.56 in.)
      Y 120 mm (4.72 in.)

      1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  12. REMOVE FRONT PILLAR GARNISH CORNER PIECE RH

    Tech Tips

    Use the same procedure as for the LH side.

  13. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  14. REMOVE REAR CONSOLE BOX COVER


    1. A003TPH

      Disengage the 4 clips.

    2. Disengage the 2 guides.

    3. Disconnect the connector and remove the rear console box cover.

  15. REMOVE UPPER CONSOLE PANEL


    1. A003S2W

      Disengage the 7 claws.

    2. Disconnect the connector and remove the upper console panel.

  16. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL


    1. A003SLR

      Remove the 2 screws <E> or <F>.

    2. A003SBJ

      Disengage the 4 claws and 6 clips, and remove the lower center instrument panel finish panel.

  17. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    1. A003TTXE02
      Text in Illustration
      *1 Stopper
      *2 Glove Compartment Door Stopper

      Disengage the claw and release the glove compartment door stopper.

    2. Bend portions (A) and (B) in the direction indicated by the arrows in the illustration to release the 2 stoppers, and lower the glove compartment door assembly until the front of the door is level.

    3. A003TCOE03
      Text in Illustration
      *1 Hinge

      Pull the glove compartment door assembly horizontally toward the rear of the vehicle to release the 2 hinges, and remove the glove compartment door assembly.

      Note

      Pulling the glove compartment door assembly upward to remove it will cause the hinges to deform when reinstalling the door. Be sure to pull out the compartment door horizontally.

  18. REMOVE NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY


    1. A003TQP

      Remove the 2 screws <C> or <D>.

    2. A003T93E01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area shown in the illustration.

    3. Disengage the claw and clip.

    4. A003TZ2

      Disengage the 2 claws and 2 clips.

    5. A003S0J

      As shown in the illustration, remove the No. 1 instrument panel box door sub-assembly.

    6. w/ USB Audio System:


      1. Disengage the clamp and disconnect the connector.

  19. DISCONNECT INSTRUMENT PANEL WIRE ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A003SLE

      Disconnect the connector.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  20. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY


    1. A003SIRE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the areas shown in the illustration.

    2. Operate the tilt lever to lower the steering wheel assembly.

    3. Disconnect the connector.

    4. Remove the 2 screws <C> or <D>.

    5. Remove the 2 passenger airbag bolts <A> or <B>.

      A003RTVE01

    6. Disengage the 4 clips and 3 claws.

      A003RHD

    7. Disengage the 5 claws and remove the upper instrument panel sub-assembly.

      A003TKC

      Note

      When removing the upper instrument panel sub-assembly, be careful not to damage it or the steering wheel assembly.

  21. REMOVE REAR SEAT HEADREST ASSEMBLY (for LH Side)

  22. REMOVE NO. 1 REAR SEAT CUSHION HINGE COVER (for LH Side)


    1. A003RHJ

      Disengage the 4 claws and remove the No. 1 rear seat cushion hinge cover.

  23. REMOVE NO. 2 REAR SEAT CUSHION HINGE COVER (for LH Side)


    1. A003U6O

      Disengage the 4 claws and remove the No. 2 rear seat cushion hinge cover.

  24. REMOVE REAR SEAT ASSEMBLY LH


    1. A003RJG

      Remove the 2 bolts on the front side of the rear seat assembly LH.

    2. A003TU1

      Recline the rear seat assembly LH forward to remove the 2 bolts and the rear seat assembly LH.

      Note

      Be careful not to damage the vehicle body.

  25. REMOVE REAR SEAT HEADREST ASSEMBLY (for RH Side)

  26. REMOVE CENTER REAR SEAT HEADREST ASSEMBLY

  27. REMOVE NO. 1 REAR SEAT CUSHION HINGE COVER (for RH Side)


    1. A003TO7

      Disengage the 4 claws and remove the No. 1 rear seat cushion hinge cover.

  28. REMOVE NO. 2 REAR SEAT CUSHION HINGE COVER (for RH Side)


    1. A003T13

      Disengage the 4 claws and remove the No. 2 rear seat cushion hinge cover.

  29. REMOVE REAR SEAT ASSEMBLY RH


    1. A003SEU

      Remove the 2 bolts on the front side of the rear seat assembly RH.

    2. A003T67

      Recline the rear seat assembly RH forward to remove the 2 bolts on the rear side and the rear seat assembly RH.

      Note

      Be careful not to damage the vehicle body.

  30. REMOVE REAR SEAT INNER BELT ASSEMBLY RH


    1. A003URL

      Remove the bolt and disconnect the rear seat center outer belt assembly with inner belt.

    2. A003S8L

      Remove the washer and rear seat inner belt assembly RH from the rear seat inner belt.

  31. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A003UER

      Disengage the 10 claws and remove the front door scuff plate LH.

  32. REMOVE COWL SIDE TRIM BOARD LH


    1. A003UBS

      Disengage the 2 clips.

    2. Disengage the guide and remove the cowl side trim board LH.

  33. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A003U8Z

      Remove the front door opening trim weatherstrip LH.

  34. REMOVE REAR DOOR SCUFF PLATE LH


    1. A003UM1

      Disengage the 8 claws and remove the rear door scuff plate LH.

  35. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A003SYQ

      Remove the rear door opening trim weatherstrip LH.

  36. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)


    1. A003STN

      Disengage the 3 claws and remove the lap belt outer anchor cover.

  37. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A003SSS

      Remove the bolt and disconnect the floor end of the front seat outer belt assembly LH.

  38. REMOVE LOWER CENTER PILLAR GARNISH LH


    1. A003RNZ

      Disengage the 4 claws and 2 clips, and remove the lower center pillar garnish LH.

  39. REMOVE UPPER CENTER PILLAR GARNISH LH


    1. A003TA3

      Remove the 2 screws.

    2. Using a clip remover, disengage the clip and remove the upper center pillar garnish LH.

  40. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  41. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure as for the LH side.

  42. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side.

  43. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  44. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side.

  45. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  46. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  47. REMOVE LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  48. REMOVE UPPER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  49. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY


    1. A003SY6

      Disengage the 2 suspenders.

    2. Disengage the 2 pins and remove the package tray trim panel assembly.

  50. REMOVE DECK FLOOR BOX LH


    1. A003TY3

      Disengage the 3 guides and remove the deck floor box LH.

  51. REMOVE DECK BOARD SUB-ASSEMBLY


    1. A003SXQ

      Disengage the 3 claws and 3 clips, and remove the deck board sub-assembly.

  52. REMOVE NO. 6 BATTERY CARRIER PANEL


    1. A003THNE01
      Text in Illustration
      *1 Double-sided Tape

      Remove the No. 6 battery carrier panel as shown in the illustration.

  53. REMOVE REAR NO. 1 FLOOR BOARD


    1. A003SLI

      Remove the bolt.

    2. Disengage the 2 claws, 2 clips and 3 guides, and remove the rear No. 1 floor board.

  54. REMOVE REAR DECK TRIM COVER


    1. A003RUK

      Disengage the 10 claws and remove the rear deck trim cover.

  55. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY (for LH Side)


    1. A003U0G

      Remove the bolt and rear seatback hinge sub-assembly.

  56. REMOVE REAR SEAT SIDE GARNISH LH


    1. A003S00

      Disengage the 6 claws and 2 clips, and remove the rear seat side garnish LH.

  57. REMOVE NO. 2 ROOM LIGHT ASSEMBLY


    1. A003RR5E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the claw.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Disconnect the connector and remove the No. 2 room light assembly.

  58. REMOVE SIDE DECK TRIM PANEL ASSEMBLY LH


    1. A003S5T

      Disengage the 2 claws and 4 clips, and remove the side deck trim panel assembly LH.

  59. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH


    1. A003SI7

      Disengage the 4 clips and remove the roof side inner garnish assembly LH.

  60. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  61. REMOVE REAR SEAT SIDE COVER RH


    1. A003TAR

      Disengage the 3 claws and 2 clips, and remove the rear seat side cover RH.

  62. REMOVE REAR SEAT SIDE GARNISH RH


    1. A003S7L

      Disengage the 6 claws and 2 clips, and remove the rear seat side garnish RH.

  63. REMOVE SIDE DECK TRIM PANEL ASSEMBLY RH


    1. A003RQJ

      Disengage the 2 claws and 4 clips, and remove the side deck trim panel assembly LH.

  64. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  65. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. A003UM5

      Disengage the 2 claws and slide the inner rear view mirror stay holder cover as shown in the illustration.

    2. A003T4T

      Disengage the 6 claws and remove the inner rear view mirror stay holder cover.

  66. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)


    1. A003SSK

      Disengage the 2 claws and remove the rain sensor cover.

  67. REMOVE MAP LIGHT ASSEMBLY


    1. A003UM4

      Using a moulding remover, disengage the 4 claws and 4 clips.

    2. Disconnect the connector and remove the map light assembly.

  68. REMOVE VISOR ASSEMBLY LH


    1. A003U0V

      Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.

    2. A003U58

      Disengage the 2 clips and remove the visor assembly LH.

    3. Remove the 2 clips from the vehicle body.

  69. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  70. REMOVE ASSIST GRIP SUB-ASSEMBLY


    1. A003UWOE04
      Text in Illustration
      *1 Protective Tape
      *a Allow the covers to come off slightly

      Using a clip remover, disengage the 4 claws.

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips


      • Gently pry on the assist grip covers as shown in the illustration to loosen them.

      • Tape the clip remover tip before use.

    2. Pull off the 2 assist grip covers by hand.

    3. A003THZ

      Disengage the 2 clips and remove the assist grip sub-assembly.

    4. Remove the 2 clips from the vehicle body.

      Tech Tips

      Use the same procedure for the other 3 assist grips.

  71. REMOVE NO. 1 ROOM LIGHT ASSEMBLY


    1. A003UMYE04
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 4 claws and remove the lens cover.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A003TH5E01

      Disengage the claw and guide, and remove the room light cover.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    3. A003S8GE03
      Text in Illustration
      *1 Protective Tape
      *a Claw (A)
      *b Claw (B)

      Using a screwdriver, disengage the 2 claws (A) as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    4. Disengage the 2 claws (B).

    5. A003RQG

      Using a screwdriver, disengage the 4 claws and remove the No. 1 room light assembly.

  72. REMOVE VISOR HOLDER


    1. A003T28E03
      Text in Illustration
      *1 45°

      Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Disengage the 2 claws and remove the visor holder.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  73. REMOVE SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)


    1. Remove the sun roof opening trim moulding.

  74. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)


    1. A003SRE

      w/ EC Mirror:


      1. Disconnect the inner rear view mirror connector.

    2. A003UND

      w/ Rain Sensor:


      1. Disconnect the rain sensor connector.

    3. Disengage each clamp from the front pillar LH.

    4. Disconnect the No. 1 roof wire connector and disengage the clamp.

    5. Disconnect the No. 2 antenna cord sub-assembly connector and disengage each clamp from the front pillar RH.

    6. Disconnect the No. 2 antenna cord sub-assembly connectors and remove the bolt from the rear pillar RH.

    7. Remove the 3 clips.

      A003RXLE01
      Text in Illustration
      *A for LHD *B for RHD
    8. A003SYU

      Remove the roof headlining assembly from the vehicle through the back door.

      Note

      Do not damage the roof headlining assembly or body interior.

  75. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)


    1. A003SRE

      w/ EC Mirror:


      1. Disconnect the inner rear view mirror connector.

    2. A003UND

      w/ Rain Sensor:


      1. Disconnect the rain sensor connector.

    3. Disengage each clamp from the front pillar LH.

    4. Disconnect the No. 1 roof wire connector and disengage the clamp.

    5. Disconnect the antenna cord sub-assembly connector and disengage each clamp from the front pillar RH.

    6. Disconnect the antenna cord sub-assembly connectors and remove the bolt from the rear pillar RH.

    7. Disconnect the sliding roof drive gear connector.

    8. Remove the 3 clips.

      A003S7ME01
      Text in Illustration
      *A for LHD *B for RHD
    9. A003T1T

      Remove the roof headlining assembly from the vehicle through the back door.

      Note

      Do not damage the roof headlining assembly or body interior.