REFRIGERANT ON-VEHICLE INSPECTION

Read the manifold gauge pressure when the following conditions are met:

Test conditions:

• Temperature at the air inlet with the switch set at RECIRC is 30 to 35°C (86 to 95°F).

• The blower speed control switch position is at "HI".

• The temperature control dial position is at "COOL".

• The A/C switch is on.

• Doors are fully open.

• The power switch is in a position that enables the A/C compressor to run.

1. 

   Normally functioning refrigeration system

   Gauge Reading

   Pressure Side	Refrigerant Volume
   Low	0.15 to 0.25 MPa (1.5 to 2.5 kgf/cm2, 21 to 36 psi)
   High	1.37 to 1.57 MPa (13.9 to 16.0 kgf/cm2, 199 to 228 psi)

2. Moisture is present in the refrigeration system.

   

   Symptom	Probable Cause	Diagnosis	Corrective Action
   During operation, pressure on low pressure side cycles between normal and vacuum	Moisture in the AC system will freeze at the expansion valve orifice, causing the refrigeration cycle to temporarily stop After the system stops, and warms up again, the ice will melt and normal operation will be temporarily restored	Cooler dryer (integrated into condenser tank) in oversaturated state Moisture in refrigeration system freezes at expansion valve orifice and blocks circulation of refrigerant	Replace cooler dryer Remove moisture in system by repeatedly evacuating air Supply a proper amount of new refrigerant

3. Insufficient cooling

   

   Symptom	Probable Cause	Diagnosis	Corrective Action
   Pressure is low on both low and high pressure sides Insufficient cooling performance	Gas leaks from the refrigeration system	Insufficient refrigerant Refrigerant leaking	Check for gas leaks and repair if necessary Supply a proper amount of new refrigerant If the gauge indicates a pressure of close to 0, then it will be necessary to evacuate the system after repairing the leak

4. Poor circulation of refrigerant

   

   Symptom	Probable Cause	Diagnosis	Corrective Action
   Pressure is low on both low and high pressure sides Frost exists on pipe from condenser to unit	Refrigerant flow is obstructed by dirt inside the pipes of the condenser core	Receiver is clogged	Replace condenser

5. Refrigerant does not circulate.

   

   Symptom	Probable Cause	Diagnosis	Corrective Action
   Vacuum is indicated on low pressure side and very low pressure is indicated on high pressure side Frost or condensation is seen on piping on both sides of receiver/dryer or expansion valve	Refrigerant flow is obstructed by moisture or dirt in refrigeration system Refrigerant flow is disrupted by gas leaks internally through the expansion valve	Refrigerant does not circulate	Check expansion valve Replace expansion valve Replace condenser Evacuate air and supply a proper amount of new refrigerant For internal gas leaks at expansion valve, replace expansion valve

6. Refrigerant is overcharged or cooling effectiveness of condenser is insufficient.

   

   Symptom	Probable Cause	Diagnosis	Corrective Action
   Pressure is too high on both low and high pressure sides	Unable to develop sufficient performance due to excessive use of refrigeration system Cooling effectiveness of condenser is insufficient	Excessive refrigerant in cycle → excessive refrigerant was added during recharging Condenser cooling effectiveness is insufficient → condenser fins are clogged at cooling fan	Clean condenser Check the operation of the condenser cooling fan If 1 and 2 are normal state, check the amount of refrigerant and supply a proper amount of refrigerant

7. Air is present in the refrigeration system.

   

   Symptom	Probable Cause	Diagnosis	Corrective Action
   Pressure is too high on both low and high pressure sides The low pressure piping is too hot to touch	Air in system	Air present in refrigeration system Insufficient vacuum purging	Check compressor oil to see if it is dirty or insufficient Evacuate the system and recharge it with new or purified refrigerant

8. Expansion valve malfunction

   

   Symptom	Probable Cause	Diagnosis	Corrective Action
   Pressure is too high on both low and high pressure sides Frost or a large amount of condensation on piping on low pressure side	Expansion valve may be stuck	Excessive refrigerant in low pressure piping Expansion valve opened too wide	Check expansion valve

9. Insufficient compressor compression

   

   Symptom	Probable Cause	Diagnosis	Corrective Action
   Pressure is too high on both low and high pressure sides Pressure is too low on high pressure side	Internal leak in compressor	Low compression Leak from a damaged valve, or parts may be broken	Replace compressor

   Gauge readings (Reference)