FRONT DOOR LOCK REMOVAL


  1. REMOVE FRONT DOOR INSIDE HANDLE BEZEL


    1. A003RJAE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws, and remove the front door inside handle bezel.

  2. REMOVE DOOR ASSIST GRIP COVER


    1. A003T8OE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver with the tip wrapped with protective tape, disengage the 4 claws and remove the door assist grip cover.

  3. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A003T3P

      Remove the 3 screws.

    2. A003SYF

      Using a clip remover, disengage the 9 clips.

    3. Disengage the 4 claws and separate the front door trim board sub-assembly from the front door inner glass weatherstrip.

    4. A003SJL

      Disengage the 2 claws and disconnect the front door inside handle sub-assembly.

    5. Disconnect each connector.

  4. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A003T68

      Disconnect the front door lock remote control cable and front door inside locking cable, and remove the front door inside handle sub-assembly.

  5. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    1. A003U7T

      Remove the front door inner glass weatherstrip from the front door panel.

  6. REMOVE FRONT DOOR SERVICE HOLE COVER


    1. A003S7R

      Disconnect the connector.

    2. Remove the front door service hole cover.

      Tech Tips

      Remove the remaining butyl tape on the door.

  7. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    1. Connect the negative battery terminal.

    2. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    3. Disconnect the negative battery terminal and power window regulator master switch assembly.

    4. A003TNQ

      Remove the 2 bolts.

      Note

      After the bolts are removed, the door glass may fall, causing damage.

    5. A003UMBE01

      Remove the front door glass sub-assembly as shown in the illustration.

      Note

      Do not damage the door glass.

  8. REMOVE FRONT DOOR GLASS RUN


    1. A003TCB

      Remove the front door glass run.

  9. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    1. A003RPUE01

      Remove the bolt and front door rear lower frame sub-assembly as shown in the illustration.

  10. REMOVE FRONT DOOR OUTSIDE HANDLE COVER


    1. A003UAQ

      Remove the hole plug.

    2. Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover and the door lock key cylinder as a unit.

      Tech Tips

      The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.

    3. A003SVA

      Using a screwdriver, disengage the 2 claws and remove the front door outside handle cover.

  11. REMOVE FRONT DOOR LOCK ASSEMBLY


    1. A003UQ8

      Using a "TORX" socket wrench (T30), remove the 3 screws.

    2. Slide the front door lock assembly downward, and remove the front door lock assembly and cables as a unit.

    3. Remove the front door lock open rod from the front door lock assembly.

    4. Remove the door lock wiring harness seal from the front door lock assembly.

  12. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. A003TWS

      Remove the front door lock remote control cable assembly.

  13. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. A003S20

      Using a screwdriver, disengage the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A003RQB

      Remove the front door inside locking cable assembly.