REAR DOOR LOCK INSTALLATION


  1. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. Install the rear door inside locking cable assembly.

    2. Engage the 3 claws.

  2. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. Install the rear door lock remote control cable assembly.

    2. Engage the claw.

  3. INSTALL REAR DOOR LOCK ASSEMBLY

    Note


    • When reusing the removed rear door lock assembly, replace the door lock wiring harness seal on the connector with a new one.

    • Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

    • Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion to the connection. This may result in a malfunction of the rear door lock assembly.


    1. Apply MP grease to the sliding parts of the rear door lock assembly.

    2. Install a new door lock wiring harness seal to the rear door lock assembly.

    3. A003S44

      Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.

    4. Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.

    5. Using a "TORX" socket wrench (T30), install the rear door lock assembly with the 3 screws.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  4. INSTALL REAR DOOR GLASS RUN


    1. A003TZP

      Install the rear door glass run.

  5. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    1. A003TJS

      Slide the rear door glass sub-assembly to install it as shown in the illustration.

  6. INSTALL REAR DOOR QUARTER WINDOW GLASS


    1. Install the rear door quarter window glass to the rear door quarter window weatherstrip.

    2. A003SID

      Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.

  7. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    1. Insert the rear door window division bar sub-assembly from above.

    2. Install the rear door glass run to the rear door window division bar sub-assembly.

    3. A003TOO

      Install the rear door window division bar sub-assembly with the 2 bolts and screw.

  8. INSTALL REAR DOOR WEATHERSTRIP


    1. A003UDA

      Engage the 16 clips and install the rear door weatherstrip.

  9. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the rear door panel.

    2. A003SZCE02
      Text in Illustration
      *1 Reference Point

      Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.

    3. Attach the rear door service hole cover by using the reference points on the rear door panel.

      Note

      Securely install the rear door service hole cover avoiding wrinkles and air bubbles.

    4. Connect the connector.

  10. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP


    1. A003SL7

      Install the rear door inner glass weatherstrip.

  11. INSTALL SWITCH BEZEL


    1. A003TL6

      Engage the 4 claws and install the switch bezel.

  12. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A003T8I

      Connect the rear door lock remote control cable and rear door inside locking cable to the rear door inside handle sub-assembly.

    2. A003SUF

      Engage the 2 claws and install the rear door inside handle sub-assembly.

  13. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. Connect the connector.

    2. A003UCF

      Engage the rear door trim board with the 3 claws on the rear door inner glass weatherstrip.

    3. Engage the 9 clips to install the rear door trim board to the rear door panel.

    4. A003RKD

      Install the 3 screws.

  14. INSTALL DOOR ASSIST GRIP COVER


    1. A003SRH

      Engage the 4 claws and install the door assist grip cover.

  15. INSTALL REAR DOOR INSIDE HANDLE BEZEL


    1. A003SOG

      Engage the 3 claws to install the rear door inside handle bezel.