REAR DOOR LOCK REMOVAL


  1. REMOVE REAR DOOR INSIDE HANDLE BEZEL


    1. A003UPWE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws and remove the rear door inside handle bezel.

  2. REMOVE DOOR ASSIST GRIP COVER


    1. A003TX0E02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver with the tip wrapped with protective tape, disengage the 4 claws and remove the door assist grip cover.

  3. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A003RKD

      Remove the 3 screws.

    2. A003UCF

      Using a clip remover, disengage the 9 clips.

    3. Disengage the 3 claws and separate the rear door trim board sub-assembly from the rear door inner glass weatherstrip.

    4. A003SUF

      Disengage the 2 claws and disconnect the rear door inside handle sub-assembly.

    5. Disconnect the connector.

  4. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A003T68

      Disconnect the rear door lock remote control cable and rear door inside locking cable, and remove the rear door inside handle sub-assembly.

  5. REMOVE SWITCH BEZEL


    1. A003TL6

      Disengage the 4 claws and remove the switch bezel.

  6. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    1. A003SL7

      Remove the rear door inner glass weatherstrip from the rear door panel.

  7. REMOVE REAR DOOR SERVICE HOLE COVER


    1. A003TZR

      Disconnect the connector.

    2. Remove the rear door service hole cover.

      Tech Tips

      Remove the remaining tape on the door.

  8. REMOVE REAR DOOR WEATHERSTRIP


    1. A003UDA

      Using a clip remover, disengage the 16 clips and remove the rear door weatherstrip.

  9. REMOVE REAR DOOR GLASS RUN


    1. A003TZP

      Remove the rear door glass run.

  10. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    1. A003TOO

      Remove the 2 bolts, screw, and rear door window division bar sub-assembly.

  11. REMOVE REAR DOOR QUARTER WINDOW GLASS


    1. A003S1N

      Remove the rear door quarter window glass and the rear door quarter window weatherstrip as a unit as shown in the illustration.

    2. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.

  12. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. A003USN

      Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      Note

      Do not damage the door glass.

  13. REMOVE REAR DOOR LOCK ASSEMBLY


    1. A003UTW

      Using a "TORX" socket wrench (T30), remove the 3 screws.

    2. Move the rear door lock assembly downward and pull the release plate out of the rear door outside handle frame.

    3. Remove the door lock wiring harness seal from the rear door lock assembly.

  14. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. A003TVL

      Using a screwdriver, disengage the claw.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A003S9C

      Remove the rear door lock remote control cable assembly.

  15. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. A003TYX

      Using a screwdriver, disengage the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A003S4T

      Remove the rear door inside locking cable assembly.