FRONT DOOR WINDOW FRAME MOULDING REMOVAL


  1. REMOVE REAR NO. 2 FLOOR BOARD


    1. A01JB5ZE01

      Disengage the 2 guides <A> as shown in the illustration.

    2. Disengage the 3 guides <B> and remove the rear No. 2 floor board.

  2. REMOVE REAR DECK FLOOR BOX


    1. Remove the rear deck floor box.

  3. REMOVE REAR NO. 3 FLOOR BOARD


    1. A01JC33

      Disengage the 2 guides and remove the rear No. 3 floor board.

  4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A01JB2W

      Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug.

  5. REMOVE ASSIST GRIP COVER


    1. A01J8SJ

      Using a moulding remover, disengage the 6 claws, 2 clips and 3 guides, and remove the assist grip cover.

  6. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. A01JCY6

      Disengage the 7 claws and 3 guides.

    2. Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.

  7. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. A01JACF

      Disengage the 7 claws and 3 guides.

    2. Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.

  8. REMOVE DOOR ARMREST COVER


    1. A01JCMQ

      Remove the door armrest cover.

  9. REMOVE COURTESY LIGHT ASSEMBLY


    1. A01J8PYE01

      Using a moulding remover, disengage the claw.

    2. Disconnect the connector and remove the courtesy light assembly.

  10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01JAQ1E01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the front door panel.

    2. A01J8I7

      Remove the 2 screws.

    3. Using a clip remover, disengage the 9 clips.

    4. Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.

    5. Raise the front door trim board sub-assembly and remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.

    6. A01JARO

      Disengage the 2 claws and disconnect the front door inside handle sub-assembly.

  11. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A01JCM2

      Disconnect the front door lock remote control cable and front door inside locking cable, and remove the front door inside handle sub-assembly.

  12. REMOVE FRONT DOOR TRIM BRACKET


    1. A01J9TD

      Remove the 2 screws and front door trim bracket.

  13. REMOVE FRONT DOOR SERVICE HOLE COVER


    1. A01JD29

      Remove the front door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  14. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    1. A01J8J2

      Remove the grommet.

    2. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.


      1. w/ Navigation System for HDD:

        Note

        After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

    3. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    4. A01JCLM

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the door glass to fall.

    5. A01JC0SE01

      Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

      Note

      Do not damage the door glass.

  15. REMOVE FRONT DOOR GLASS RUN


    1. A01JD3R

      Remove the front door glass run.

  16. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY


    1. A01J9IFE01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the front door belt moulding assembly.

    2. A01JBQE

      Using a screwdriver, disengage the 7 claws and remove the front door belt moulding assembly.

  17. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

    Tech Tips

    When removing the front door rear window frame moulding, heat the vehicle body and front door rear window frame moulding using a heat light.

    Heating Temperature
    Item Temperature
    Vehicle Body 40 to 60°C (104 to 140°F)
    Moulding 20 to 30°C (68 to 86°F)

    Note

    Do not heat the vehicle body or front door rear window frame moulding moulding excessively.


    1. Using a heat light, heat the front door rear window frame moulding.

    2. A01JAB2E01
      Text in Illustration
      *1 Double-sided Tape

      Using a moulding remover, remove the clip and front door rear window frame moulding.