REAR DOOR BELT MOULDING INSTALLATION


  1. INSTALL REAR DOOR BELT MOULDING ASSEMBLY


    1. A01J9KC

      Engage the 7 claws to install the rear door belt moulding assembly.

  2. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    1. Connect the cable to the negative (-) battery terminal and the rear power window regulator motor connector.

    2. Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.

    3. Disconnect the power window regulator switch assembly and rear power window regulator motor connector.


      1. w/ Navigation System for HDD:

        Note

        After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

    4. Disconnect the cable from the negative (-) battery terminal.

    5. A01JC4L

      Insert the rear door glass sub-assembly into the rear door panel along the rear door glass run as shown in the illustration.

    6. Install the rear door glass sub-assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    7. Connect the cable to the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. INSTALL REAR DOOR REAR GUIDE SEAL


    1. Install the temporary screw to the rear door rear guide seal.

    2. A01J8Q9E01
      Text in Illustration
      *1 Temporary Screw

      Temporarily install the rear door rear guide seal.

    3. Install the 2 screws.

    4. Tighten the temporary screw to install the rear door rear guide seal.

  4. INSTALL REAR DOOR WINDOW GUIDE SUB-ASSEMBLY


    1. A01JA23

      Install the screw.

    2. Install the rear door window guide sub-assembly with the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  5. INSTALL REAR DOOR GLASS RUN


    1. A01JCIU

      Install the rear door glass run.

  6. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the rear door panel.

    2. A01JCSJE01
      Text in Illustration
      *1 Reference Point

      Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.

    3. Attach the rear door service hole cover according to the reference points on the rear door panel.

      Note

      Securely install the rear door service hole cover preventing wrinkles and air bubbles.

    4. Connect the 2 connectors.

    5. Engage the clamp.

  7. INSTALL REAR DOOR TRIM BRACKET


    1. A01JAN5

      Install the rear door trim bracket with the 2 screws.

  8. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A01JA0W

      Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door inside handle.

    2. A01J8OM

      Engage the 2 claws and install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.

  9. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. for 8 Speakers:


      1. Connect the connector.

    2. A01J8PS

      Engage the 8 clips and install the rear door trim board sub-assembly.

    3. Install the 2 screws.

    4. Remove the protective tape.

  10. INSTALL REAR DOOR ARMREST COVER


    1. A01JBG5

      Install the rear door armrest cover.

  11. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. Connect the connector.

    2. A01JBGI

      Engage the 7 claws and 2 guides, and install the rear power window regulator switch assembly with rear door armrest base panel.

  12. INSTALL DOOR ASSIST GRIP COVER


    1. A01J8GK

      Engage the 6 claws, 2 clips and 3 guides, and install the assist grip cover.

  13. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A01J9NW

      Engage the 3 claws and install the rear door inside handle bezel plug.

  14. INSTALL REAR NO. 3 FLOOR BOARD


    1. A01JC33

      Engage the 2 guides to install the rear No. 3 floor board.

  15. INSTALL REAR DECK FLOOR BOX


    1. Install the rear deck floor box.

  16. INSTALL REAR NO. 2 FLOOR BOARD


    1. A01JCWRE01

      Engage the 3 guides <A>.

    2. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.

  17. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here