REAR COMBINATION LIGHT ASSEMBLY INSTALLATION


  1. INSTALL REAR COMBINATION LIGHT ASSEMBLY


    1. A01J8QJ

      Engage the guide and 2 clips, and install the rear combination light assembly as shown in the illustration.

      CAUTION:

      When installing the rear combination light assembly, check that the wire harness is not caught between the rear combination light assembly and the body. Failure to do so may cause a short circuit.

    2. A01JAPW

      Install the 2 nuts.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    3. Connect the connector.

  2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)


    1. Connect the connector.

    2. Engage the 7 claws and 2 clips.

    3. Install the deck trim side panel assembly LH with the screw.

      A01J8UZ

  3. INSTALL TONNEAU COVER HOLDER CAP (for LH Side)


    1. A01JASW

      Engage the claw to install the tonneau cover holder cap.

  4. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)


    1. A01JAKN

      Engage the 2 guides.

    2. Install the 2 luggage hold belt striker assemblies with the 2 bolts.

  5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)


    1. Engage the 7 claws and 2 clips.

    2. Install the deck trim side panel assembly RH with the screw.

      A01JCY2

  6. INSTALL TONNEAU COVER HOLDER CAP (for RH Side)

    Tech Tips

    Use the same procedure for the RH side and LH side.

  7. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure for the RH side and LH side.

  8. INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for LH Side)


    1. A01JABT

      Engage the 2 guides as shown in the illustration.

    2. A01J9D6

      Install the rear side seatback assembly LH with the bolt.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  9. INSTALL REAR SIDE SEATBACK ASSEMBLY RH (for RH Side)

    Tech Tips

    Use the same procedure for the RH side and LH side.

  10. INSTALL REAR SEAT CUSHION ASSEMBLY


    1. A01JCUFE01
      Text in Illustration
      *1 100 mm (3.94 in.) or less
      *2 Guide
      *3 Hook

      Engage the 2 guides of the seat cushion to the seatback.

    2. Engage the 2 front hooks of the seat cushion to the vehicle body.

      Note

      When installing the seat cushion, make sure that the seat belt buckle is not under the seat cushion.

      Tech Tips

      Confirm that the seat cushion is firmly installed.

  11. INSTALL REAR DECK TRIM COVER


    1. A01JCDX

      Engage the 4 claws and 4 guides to install the rear deck trim cover.

  12. INSTALL DECK TRIM SERVICE HOLE COVER


    1. A01JD05

      Engage the 3 guides.

    2. Engage the 2 claws to install the deck trim service hole cover.

  13. INSTALL REAR NO. 1 FLOOR BOARD


    1. A01JBVX

      Engage the 2 claws and 2 clips.

    2. Install the rear No. 1 floor board with the bolt.

  14. INSTALL REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY


    1. A01JCFP

      Engage the claw and 2 clips to install the rear No. 2 floor board sub-assembly.

  15. INSTALL REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY


    1. A01J8Q1

      Engage the 2 claws and 2 clips to install the rear No. 1 floor board sub-assembly.

  16. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Install the tonneau cover assembly.

  17. INSTALL DECK FLOOR BOX LH (for LH Side)


    1. A01J9G6

      Engage the 2 guides.

    2. Install the deck floor box LH with the clip.

  18. INSTALL REAR NO. 4 FLOOR BOARD (for LH Side)


    1. A01JB13

      Engage the guide to install the rear No. 4 floor board.

  19. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP


    1. A01JBZWE01
      Text in Illustration
      *1 Alignment Mark (Red)

      Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  20. INSTALL REAR DOOR SCUFF PLATE


    1. A01JA7L

      Engage the 7 claws to install the rear door scuff plate LH.

  21. INSTALL REAR NO. 3 FLOOR BOARD (for RH Side)


    1. A01JC33

      Engage the 2 guides to install the rear No. 3 floor board.

  22. INSTALL REAR DECK FLOOR BOX


    1. Install the rear deck floor box.

  23. INSTALL REAR NO. 2 FLOOR BOARD


    1. A01JCWRE01

      Engage the 3 guides <A>.

    2. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.

  24. INSTALL REAR BUMPER ASSEMBLY


    1. A01JA19

      Engage the 4 claws and install the rear bumper assembly as shown in the illustration.

    2. A01JCL2

      Engage the 5 claws.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    3. A01JA49

      Install the screw.

      Torque:
      3.0 N*m  { 31 kgf*cm, 27 in.*lbf }

      Tech Tips

      Use the same procedure for the RH side and LH side.

    4. Engage the claw.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    5. A01JBRJ

      Engage the 2 rear bumper upper stoppers and install the 2 screws.

    6. A01J94C

      Install the 9 clips.

    7. Install the nut.

  25. BUMPER POSITION SETTING (w/ Intelligent Parking Assist System)

    Click here