LIGHTING SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuator and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / (desired system) / Data List.

    5. Read the Data List according to the display on the intelligent tester.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      IG SW Power switch IG signal/ON or OFF

      ON: Power switch on (IG)

      OFF: Power switch off

      		 -
      Parking Brake SW Parking brake switch signal/ON or OFF

      ON: Parking brake switch on

      OFF: Parking brake switch off

      		 -
      RR Door Courtesy SW Rear door courtesy light switch RH/ON or OFF

      ON: Rear door RH or LH open

      OFF: Rear door RH and LH closed

      		 -
      RL Door Courtesy SW Rear door courtesy light switch LH/ON or OFF

      ON: Rear door RH or LH open

      OFF: Rear door RH and LH closed

      		 -
      Back Door Courtesy SW Back door courtesy switch signal/ON or OFF

      ON: Back door open

      OFF: Back door closed

      		 -
      FR Door Courtesy Front door courtesy light switch RH signal/ON or OFF

      ON: Front door RH open

      OFF: Front door RH closed

      		 -
      FL Door Courtesy Front door courtesy light switch LH signal/ON or OFF

      ON: Front door LH open

      OFF: Front door LH closed

      		 -
      Dimmer SW Dimmer switch high position signal/ON or OFF

      ON: Dimmer switch in high or high flash position

      OFF: Dimmer switch in low position

      		 -
      Passing Light SW Dimmer switch high flash position (pass) signal/ON or OFF

      ON: Dimmer switch in high flash position

      OFF: Dimmer switch not in high flash position

      		 -
      Rear Fog Light SW Rear fog light switch signal/ON or OFF

      ON: Rear fog light switch on

      OFF: Rear fog light switch off

      		 -
      Front Fog Light SW Front fog light switch signal/ON or OFF

      ON: Front fog light switch on

      OFF: Front fog light switch off

      		 -
      Auto Light SW Light control switch AUTO position signal/ON or OFF

      ON: Light control switch in AUTO position

      OFF: Light control switch not in AUTO position

      		 -
      Head Light SW (Head) Light control switch head position signal/ON or OFF

      ON: Light control switch in head position

      OFF: Light control switch not in head position

      		 -
      Head Light SW (Tail) Light control switch tail position signal/ON or OFF

      ON: Light control switch in tail or head position

      OFF: Light control switch in neither tail nor head position

      		 -
      Illumination Rate Info Illumination rate information/0 ms. to 99.99 ms. Value is output according to ambient light levels -
      HL Auto Leveling
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Headlight Low Beam State Low beam headlight state/ON or OFF

      ON: Low beam headlights on

      OFF: Low beam headlights off

      		 -
      +B IG power supply voltage value/0 to 19.75 V 11 to 14 V -
      Height Sens Pw Supply Val Height control sensor power supply value/0 to 6.25 V Approx. 5 V -
      Rr Height Sens Signal Val Rear height control sensor signal value/0 to 5 V Approx. 2.5 V (When vehicle is level) Value changes according to vehicle height
      Vehicle Speed Vehicle speed/0 to 327.67 km/h Condition can be displayed -
      Rear Height Adjust Valid Flag Rear height adjustment range/VALID or INVALID Condition can be displayed -
      Init Writing Count Number of times for initialization/0 to 255 Condition can be displayed -
      Number Of Trouble Codes Number of trouble codes/0 to 255 Condition can be displayed -

  2. ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / (desired system) / Active Test.

    5. Perform the Active Test according to the display on the intelligent tester.

      Main Body
      Tester Display Test Part Control Range Diagnostic Note
      Daytime Running Light Daytime running lights ON/OFF -
      Taillight Relay Taillight relay ON/OFF -
      Headlight Relay Headlight relays ON/OFF -
      Head Light Hi High beam headlights ON/OFF -
      Front Fog Light Relay Front fog light relay ON/OFF Light control switch is in tail position
      Rear Fog Light Relay Rear fog light relay ON/OFF Light control switch is in tail position
      HL Auto Leveling
      Tester Display Test Part Control Range Diagnostic Note
      Drive The Leveling Motor UP*1 Leveling motor upward operation ON/OFF

      ON: Move up

      OFF: Stop
      Drive The Leveling Motor DOWN*1 Leveling motor downward operation ON/OFF

      ON: Move down

      OFF: Stop

      *1: Perform the active test with the power switch on (READY) and vehicle stopped.