WIPER ECU REMOVAL


  1. PRECAUTION (w/ Navigation System for HDD)

    Note

    After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

  2. REMOVE REAR NO. 2 FLOOR BOARD (w/ Navigation System for HDD)


    1. A01JB5ZE01

      Disengage the 2 guides <A> as shown in the illustration.

    2. Disengage the 3 guides <B> and remove the rear No. 2 floor board.

  3. REMOVE REAR DECK FLOOR BOX (w/ Navigation System for HDD)


    1. Remove the rear deck floor box.

  4. REMOVE REAR NO. 3 FLOOR BOARD (w/ Navigation System for HDD)


    1. A01JC33

      Disengage the 2 guides and remove the rear No. 3 floor board.

  5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Navigation System for HDD)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  6. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY


    1. A01J9ZGE01
      Text in Illustration
      *a Lift slightly

      Using a moulding remover, slightly lift the panel at the position shown in the illustration.

    2. Pull the integration control and panel assembly in the direction indicated by the arrow to disengage the 6 claws.

    3. Disconnect each connector and remove the integration control and panel assembly.

  7. REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. A01JA02

      Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 2 claws and 2 clips.

    2. A01JAMJ

      Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 5 claws and remove the lower center instrument cluster finish panel sub-assembly.

  8. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Disengage the 14 claws.

    2. Disconnect the connector and remove the instrument cluster finish panel garnish.

      A01J8FE

  9. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A01JD4M

      Disengage the 3 claws.

    2. Disconnect the connector and remove the upper instrument panel finish panel sub-assembly.

  10. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Radio Receiver)


    1. A01JADX

      Disengage the 4 claws and remove the center instrument cluster finish panel sub-assembly.

  11. REMOVE RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)


    1. A01JBMF

      Remove the 4 bolts <B> and radio tuner opening cover with bracket.

  12. REMOVE RADIO RECEIVER WITH BRACKET (w/ Radio Receiver)


    1. A01JD1M

      Remove the 4 bolts.

    2. A01J8MZ

      Disengage the 4 claws as shown in the illustration.

    3. Disconnect each connector and remove the radio receiver with bracket.

  13. REMOVE NAVIGATION RECEIVER WITH BRACKET (w/ Navigation System)


    1. A01JCMN

      Remove the 4 bolts.

    2. A01J9QE

      Disengage the 4 claws and remove the navigation receiver assembly with bracket as shown in the illustration.

    3. Disconnect each connector.

  14. REMOVE WINDSHIELD WIPER RELAY ASSEMBLY


    1. Disconnect the connector.

    2. A01JDAS

      Remove the bolt and the windshield wiper relay assembly.