FRONT WIPER MOTOR INSTALLATION


  1. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY


    1. Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly with the 2 bolts.

      Torque:
      7.5 N*m  { 77 kgf*cm, 66 in.*lbf }

  2. INSTALL FRONT WIPER CRANK SUB-ASSEMBLY


    1. When replacing the windshield wiper motor assembly and front wiper crank sub-assembly with a new one:


      1. A01J8HE

        Temporarily install a front wiper crank sub-assembly on the new windshield wiper motor assembly with the nut.

      2. Temporarily install the windshield wiper motor and link on the crank arm pivot of the front wiper crank sub-assembly.

      3. Align the front wiper crank sub-assembly with the windshield wiper motor and link as shown in the illustration.

        A01JC42E01
        Text in Illustration
        *1 Front Wiper Crank Sub-assembly

      4. Install the front wiper crank sub-assembly with the nut.

        Torque:
        17 N*m  { 175 kgf*cm, 13 ft.*lbf }

    2. When reusing the windshield wiper motor assembly and front wiper crank sub-assembly:


      1. A01JBS7E01
        Text in Illustration
        *1 Matchmark

        Align the matchmarks and install the front wiper crank sub-assembly with the nut.

        Torque:
        17 N*m  { 175 kgf*cm, 13 ft.*lbf }
    3. A01JAJZE01
      Text in Illustration
      *1 Crank Arm Pivot

      Apply MP grease to the crank arm pivot of the front wiper crank sub-assembly.

    4. A01JCL6

      Connect the rod of the windshield wiper link assembly to the crank arm pivot of the front wiper crank sub-assembly.

  3. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    1. Connect the connector.

      A01JCWUE01
      Text in Illustration
      *A for LHD: *B for RHD:
      *1 Grommet - -

    2. Engage the grommet as shown in the illustration.

    3. Install the windshield wiper motor and link assembly with the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    4. Engage the 2 clamps.

      Note

      Be careful not to damage the windshield when installing the windshield wiper motor and link assembly.

  4. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)


    1. Engage the 8 guides <B>.

      A01JBOYE01

    2. Engage the 5 claws and 3 guides <A> to install the cowl top ventilator louver sub-assembly as shown in the illustration.

    3. A01J9V7

      Install the 2 clips.

  5. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)


    1. Engage the 8 guides <B>.

      A01J8O9E01

    2. Engage the 6 claws and 3 guides <A> to install the cowl top ventilator louver sub-assembly as shown in the illustration.

    3. A01J9RK

      Install the 2 clips.

  6. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH


    1. A01JCH7E01

      Engage the guide <B> as shown in the illustration.

    2. Engage the claw and guide <A> to install the cowl side ventilator sub-assembly LH as shown in the illustration.

  7. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

  8. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

    2. A01JCYCE06
      Text in Illustration
      *1 Wiper Arm Serration
      *2 Wire Brush
      *3 Wiper Pivot Serration

      When reusing the front wiper arm and blade assembly RH:


      1. Clean the wiper arm serrations.

    3. When reusing the windshield wiper link assembly:


      1. Clean the wiper pivot serrations with a wire brush.

    4. A01J908E01
      Text in Illustration
      *1 Ceramic Dot

      Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

      Torque:
      23 N*m  { 235 kgf*cm, 17 ft.*lbf }

      Tech Tips

      Hold the wiper arm by hand while tightening the nut.

  9. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. A01JCYCE05
      Text in Illustration
      *1 Wiper Arm Serration
      *2 Wire Brush
      *3 Wiper Pivot Serration

      When reusing the front wiper arm and blade assembly LH:


      1. Clean the wiper arm serrations.

    2. When reusing the windshield wiper link assembly:


      1. Clean the wiper pivot serrations with a wire brush.

    3. A01J90PE01
      Text in Illustration
      *1 Ceramic Dot

      Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

      Torque:
      23 N*m  { 235 kgf*cm, 17 ft.*lbf }

      Tech Tips

      Hold the wiper arm by hand while tightening the nut.

    4. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.

  10. INSTALL FRONT WIPER ARM HEAD CAP


    1. A01JAHD

      Engage the 3 claws to install the front wiper arm head cap.

      Tech Tips

      Use the same procedure for the RH side and LH side.