OUTER REAR VIEW MIRROR INSPECTION

INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

1. Inspect the operation of the mirror surface.

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

      Disconnect the outer rear view mirror assembly LH connector.

   2. Apply battery voltage and check the operation of the mirror.

      OK

      Measurement Condition Specified Condition Battery positive (+) → Terminal 6 (MV) Battery negative (-) → Terminal 5 (M+) Turns upward Battery positive (+) → Terminal 5 (M+) Battery negative (-) → Terminal 6 (MV) Turns downward Battery positive (+) → Terminal 4 (MH) Battery negative (-) → Terminal 5 (M+) Turns left Battery positive (+) → Terminal 5 (M+) Battery negative (-) → Terminal 4 (MH) Turns right

      If the result is not as specified, replace the outer rear view mirror assembly LH.

2. Check the mirror heater (w/ Mirror heater).

   
   

   1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition Terminal 1 (HL-) - Terminal 2 (HL+) 25°C (77°F) 7.6 to 11.4 Ω

      If the result is not as specified, replace the outer rear view mirror assembly.

INSPECT OUTER MIRROR RETRACTOR LH

1. Inspect the operation of the retractable mirror.

   Note

   
   

   • Disconnect and reconnect the battery between each mirror position check.

   • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

   
   
   1. 

      Text in Illustration

      *1	(A) Forward Position
      *2	(B)
      *3	(C) Driving position
      *4	(D)
      *5	(E) Retracted Position
      *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

      Disconnect the outer rear view mirror assembly LH connector.

   2. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

      OK

      Tester Connection Condition Specified Condition Battery positive (+) → Terminal 11 (MR) Battery negative (-) → Terminal 10 (MF) Forward position (A) Moves from (A) to retracted position (E) Battery positive (+) → Terminal 10 (MF) Battery negative (-) → Terminal 11 (MR) Forward position (A) Does not move Battery positive (+) → Terminal 11 (MR) Battery negative (-) → Terminal 10 (MF) Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E) Battery positive (+) → Terminal 10 (MF) Battery negative (-) → Terminal 11 (MR) Position between forward position (A) and driving position (C) Moves from (B) to forward position (A) Battery positive (+) → Terminal 11 (MR) Battery negative (-) → Terminal 10 (MF) Driving position (C) Moves from (C) to retracted position (E) Battery positive (+) → Terminal 10 (MF) Battery negative (-) → Terminal 11 (MR) Driving position (C) Does not move Battery positive (+) → Terminal 11 (MR) Battery negative (-) → Terminal 10 (MF) Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E) Battery positive (+) → Terminal 10 (MF) Battery negative (-) → Terminal 11 (MR) Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C) Battery positive (+) → Terminal 11 (MR) Battery negative (-) → Terminal 10 (MF) Retracted position (E) Does not move Battery positive (+) → Terminal 10 (MF) Battery negative (-) → Terminal 11 (MR) Retracted position (E) Moves from (E) to driving position (C)

      If the result is not as specified, replace the outer rear view mirror assembly LH.

INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

1. Inspect the operation of the mirror surface.

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

      Disconnect the outer rear view mirror assembly RH connector.

   2. Apply battery voltage and check the operation of the mirror.

      OK

      Measurement Condition Specified Condition Battery positive (+) → Terminal 6 (MV) Battery negative (-) → Terminal 5 (M+) Turns upward Battery positive (+) → Terminal 5 (M+) Battery negative (-) → Terminal 6 (MV) Turns downward Battery positive (+) → Terminal 4 (MH) Battery negative (-) → Terminal 5 (M+) Turns left Battery positive (+) → Terminal 5 (M+) Battery negative (-) → Terminal 4 (MH) Turns right

      If the result is not as specified, replace the outer rear view mirror assembly RH.

2. Check the mirror heater (w/ Mirror heater).

   
   

   1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition Terminal 1 (HR-) - Terminal 2 (HR+) 25°C (77°F) 7.6 to 11.4 Ω

      If the result is not as specified, replace the outer rear view mirror assembly.

INSPECT OUTER MIRROR RETRACTOR RH

1. Inspect the operation of the retractable mirror.

   Note

   
   

   • Disconnect and reconnect the battery between each mirror position check.

   • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

   
   
   1. 

      Text in Illustration

      *1	(A) Forward Position
      *2	(B)
      *3	(C) Driving position
      *4	(D)
      *5	(E) Retracted Position
      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

      Disconnect the outer rear view mirror assembly RH connector.

   2. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

      OK

      Tester Connection Condition Specified Condition Battery positive (+) → Terminal 11 (MR) Battery negative (-) → Terminal 10 (MF) Forward position (A) Moves from (A) to retracted position (E) Battery positive (+) → Terminal 10 (MF) Battery negative (-) → Terminal 11 (MR) Forward position (A) Does not move Battery positive (+) → Terminal 11 (MR) Battery negative (-) → Terminal 10 (MF) Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E) Battery positive (+) → Terminal 10 (MF) Battery negative (-) → Terminal 11 (MR) Position between forward position (A) and driving position (C) Moves from (B) to forward position (A) Battery positive (+) → Terminal 11 (MR) Battery negative (-) → Terminal 10 (MF) Driving position (C) Moves from (C) to retracted position (E) Battery positive (+) → Terminal 10 (MF) Battery negative (-) → Terminal 11 (MR) Driving position (C) Does not move Battery positive (+) → Terminal 11 (MR) Battery negative (-) → Terminal 10 (MF) Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E) Battery positive (+) → Terminal 10 (MF) Battery negative (-) → Terminal 11 (MR) Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C) Battery positive (+) → Terminal 11 (MR) Battery negative (-) → Terminal 10 (MF) Retracted position (E) Does not move Battery positive (+) → Terminal 10 (MF) Battery negative (-) → Terminal 11 (MR) Retracted position (E) Moves from (E) to driving position (C)

      If the result is not as specified, replace the outer rear view mirror assembly RH.