POWER WINDOW REGULATOR MOTOR (for Front Door) REMOVAL

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.


  1. REMOVE REAR NO. 2 FLOOR BOARD


    1. A01JB5ZE01

      Disengage the 2 guides <A> as shown in the illustration.

    2. Disengage the 3 guides <B> and remove the rear No. 2 floor board.

  2. REMOVE REAR DECK FLOOR BOX


    1. Remove the rear deck floor box.

  3. REMOVE REAR NO. 3 FLOOR BOARD


    1. A01JC33

      Disengage the 2 guides and remove the rear No. 3 floor board.

  4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A01JB2W

      Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug.

  5. REMOVE ASSIST GRIP COVER


    1. A01J8SJ

      Using a moulding remover, disengage the 6 claws, 2 clips and 3 guides, and remove the assist grip cover.

  6. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. A01JCY6

      Disengage the 7 claws and 3 guides.

    2. Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.

  7. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. A01JACF

      Disengage the 7 claws and 3 guides.

    2. Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.

  8. REMOVE DOOR ARMREST COVER


    1. A01JCMQ

      Remove the door armrest cover.

  9. REMOVE COURTESY LIGHT ASSEMBLY


    1. A01J8PYE01

      Using a moulding remover, disengage the claw.

    2. Disconnect the connector and remove the courtesy light assembly.

  10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01JAQ1E01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the front door panel.

    2. A01J8I7

      Remove the 2 screws.

    3. Using a clip remover, disengage the 9 clips.

    4. Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.

    5. Raise the front door trim board sub-assembly and remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.

    6. A01JARO

      Disengage the 2 claws and disconnect the front door inside handle sub-assembly.

  11. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A01JCM2

      Disconnect the front door lock remote control cable and front door inside locking cable, and remove the front door inside handle sub-assembly.

  12. REMOVE FRONT DOOR TRIM BRACKET


    1. A01J9TD

      Remove the 2 screws and front door trim bracket.

  13. REMOVE FRONT DOOR SERVICE HOLE COVER


    1. A01JD29

      Remove the front door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  14. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    1. A01J8J2

      Remove the grommet.

    2. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.


      1. w/ Navigation System for HDD:

        Note

        After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

    3. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    4. A01JCLM

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the door glass to fall.

    5. A01JC0SE01

      Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

      Note

      Do not damage the door glass.

  15. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY


    1. A01JB0RE01
      Text in Illustration
      *1 Temporary Bolt

      Disconnect the connector.

    2. Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.

    3. Remove the 5 bolts.

    4. Remove the front door window regulator assembly.

    5. Remove the temporary bolt from the front door window regulator assembly.

  16. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY


    1. A01J8YB

      Using a T25 "TORX" driver, remove the 3 screws and the front power window regulator motor assembly.