ROOF HEADLINING INSTALLATION


  1. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)


    1. A01JBL4

      Put the roof headlining assembly into the vehicle through the back door.

      Note

      Do not damage the roof headlining assembly or body interior.

    2. Install the 5 clips.

    3. Connect the 2 connectors to the connector holder.

    4. Engage the 4 clamps to the front pillar LH.

    5. Connect the connector and engage the clamp to the rear pillar RH.

    6. Connect the connector and engage the 3 clamps to the front pillar RH.

    7. w/ EC Mirror:


      1. Connect the inner rear view mirror connector and engage the 2 clamps.

    8. w/ Rain sensor:


      1. Connect the rain sensor connector and engage the 2 clamps.

        A01JBSNE01
        Text in Illustration
        *1 w/ EC Mirror *2 w/ Rain Sensor

  2. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)


    1. A01JCS8

      Put the roof headlining assembly into the vehicle through the back door.

      Note

      Do not damage the roof headlining assembly or body interior.

    2. Engage the 6 fasteners.

      A01J9W9

    3. Install the 3 clips.

    4. Connect the 2 connectors to the connector holder.

    5. Engage the 4 clamps to the front pillar LH.

    6. Connect the connector and engage the clamp to the rear pillar RH.

    7. Connect the connector and engage the 3 clamps to the front pillar RH.

    8. w/ EC Mirror:


      1. Connect the inner rear view mirror connector and engage the 2 clamps.

    9. w/ Rain sensor:


      1. Connect the rain sensor connector and engage the 2 clamps.

        A01JATKE01
        Text in Illustration
        *1 w/ EC Mirror *2 w/ Rain Sensor

  3. INSTALL VISOR HOLDER


    1. A01JCBF

      Engage the 2 claws.

    2. Push in the visor holder as shown in the illustration.

      Tech Tips

      Use the same procedure for the other visor holder.

  4. INSTALL VISOR ASSEMBLY LH


    1. A01J8GB

      Engage the 2 clips to install the visor assembly LH.

  5. INSTALL VISOR BRACKET COVER LH


    1. A01J9CA

      Engage the 3 claws to install the visor bracket cover LH.

  6. INSTALL VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  7. INSTALL VISOR BRACKET COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  8. INSTALL FRONT ASSIST GRIP ASSEMBLY


    1. A01J8TH

      Assemble the front assist grip assembly as shown in the illustration.

    2. A01JCDV

      Install the front assist grip assembly.

      Tech Tips

      Use the same procedure for the other front assist grip.

  9. INSTALL REAR ASSIST GRIP ASSEMBLY


    1. A01JAS1

      Assemble the rear assist grip assembly as shown in the illustration.

    2. A01JBXV

      Install the rear assist grip assembly.

      Tech Tips

      Use the same procedure for the other rear assist grip.

  10. INSTALL NO. 1 ROOM LIGHT ASSEMBLY


    1. A01JCUUE01
      Text in Illustration
      *1 Switch Part of Room Light Switch Base
      *2 Switch Part of No. 1 Room Light Assembly

      Align the switch parts shown in the illustration and engage the 4 claws to install the room light switch base to the No. 1 room light assembly.

    2. A01J9TN

      Engage the 4 claws and install the No. 1 room light assembly.

    3. A01JC71

      Engage the 2 claws and 2 guides to install the 2 No. 1 room light covers.

    4. A01JC18

      Engage the 4 claws to install the No. 1 room light lens.

  11. INSTALL MAP LIGHT ASSEMBLY (w/o Sliding Roof)


    1. Connect the connector.

    2. A01JBKP

      Engage the 2 guides and 4 clips, and install the map light assembly.

  12. INSTALL MAP LIGHT ASSEMBLY (w/ Sliding Roof)


    1. Connect the connector.

    2. A01JCN3

      Engage the 2 guides and 4 clips, and install the map light assembly.

  13. INSTALL ROOF TOP MOULDING


    1. A01JBC1

      Engage the 3 claws and 2 clips to install the roof top moulding.

  14. INSTALL INNER REAR VIEW MIRROR COVER (w/ EC Mirror)


    1. A01JBBW

      Engage the 6 claws and install the inner rear view mirror cover.

    2. A01J9JS

      Engage the 2 claws and install the inner rear view mirror cover as shown in the illustration.

  15. INSTALL RAIN SENSOR COVER (w/ Rain Sensor)


    1. A01J95Z

      Engage the 2 claws.

    2. Install the rain sensor cover as shown in the illustration.

  16. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH


    1. Engage the 9 clips to install the roof side inner garnish assembly LH.

      A01JCXV

  17. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Connect the connector.

    2. Engage the 7 claws and 2 clips.

    3. Install the deck trim side panel assembly LH with the screw.

      A01J8UZ

  18. INSTALL TONNEAU COVER HOLDER CAP (for LH Side)


    1. A01JASW

      Engage the claw to install the tonneau cover holder cap.

  19. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)


    1. A01JAKN

      Engage the 2 guides.

    2. Install the 2 luggage hold belt striker assemblies with the 2 bolts.

  20. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  21. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH


    1. Engage the 7 claws and 2 clips.

    2. Install the deck trim side panel assembly RH with the screw.

      A01JCY2

  22. INSTALL TONNEAU COVER HOLDER CAP (for RH Side)

    Tech Tips

    Use the same procedure described for the LH side.

  23. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure described for the LH side.

  24. INSTALL REAR DECK TRIM COVER


    1. A01JCDX

      Engage the 4 claws and 4 guides to install the rear deck trim cover.

  25. INSTALL DECK TRIM SERVICE HOLE COVER


    1. A01JD05

      Engage the 3 guides.

    2. Engage the 2 claws to install the deck trim service hole cover.

  26. INSTALL REAR NO. 1 FLOOR BOARD


    1. A01JBVX

      Engage the 2 claws and 2 clips.

    2. Install the rear No. 1 floor board with the bolt.

  27. INSTALL REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY


    1. A01JCFP

      Engage the claw and 2 clips to install the rear No. 2 floor board sub-assembly.

  28. INSTALL REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY


    1. A01J8Q1

      Engage the 2 claws and 2 clips to install the rear No. 1 floor board sub-assembly.

  29. INSTALL DECK FLOOR BOX LH


    1. A01J9G6

      Engage the 2 guides.

    2. Install the deck floor box LH with the clip.

  30. INSTALL REAR NO. 4 FLOOR BOARD


    1. A01JB13

      Engage the guide to install the rear No. 4 floor board.

  31. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Install the tonneau cover assembly.

  32. INSTALL UPPER INSTRUMENT PANEL ASSEMBLY


    1. Install the upper instrument panel assembly Click here.

  33. INSTALL REAR SIDE SEATBACK ASSEMBLY LH


    1. A01JABT

      Engage the 2 guides as shown in the illustration.

    2. A01J9D6

      Install the rear side seatback assembly LH with the bolt.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  34. INSTALL REAR SIDE SEATBACK ASSEMBLY RH


    1. A01J9RZ

      Engage the 2 guides as shown in the illustration.

    2. A01JCTM

      Install the rear side seatback assembly RH with the bolt.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  35. INSTALL REAR SEAT CUSHION ASSEMBLY


    1. A01JCUFE01
      Text in Illustration
      *1 100 mm (3.94 in.) or less
      *2 Guide
      *3 Hook

      Engage the 2 guides of the seat cushion to the seatback.

    2. Engage the 2 front hooks of the seat cushion to the vehicle body.

      Note

      When installing the seat cushion, make sure that the seat belt buckle is not under the seat cushion.

      Tech Tips

      Confirm that the seat cushion is firmly installed.

  36. INSTALL CENTER PILLAR GARNISH LH


    1. Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar garnish LH.

    2. A01J9M7

      Engage the clip.

    3. Install the center pillar garnish LH with the screw.

  37. INSTALL CENTER PILLAR LOWER GARNISH LH


    1. A01JAI1

      Engage the 2 claws and 2 clips to install the center pillar lower garnish LH.

  38. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A01J9GA

      Install the floor end of the front seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. Check if the ELR locks.

      Note

      The check should be performed with the outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  39. INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)


    1. A01JB4X

      Engage the 3 claws to install the lap belt outer anchor cover.

  40. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01JBZWE01
      Text in Illustration
      *1 Alignment Mark (Red)

      Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  41. INSTALL REAR DOOR SCUFF PLATE LH


    1. A01JA7L

      Engage the 7 claws to install the rear door scuff plate LH.

  42. INSTALL FRONT PILLAR GARNISH LH


    1. A01JBCIE01
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      Remove the protective cover.

    2. A01JD90E01
      Text in Illustration
      *1 Front Pillar Garnish Clip
      *2 Protective Tape

      Make sure that the front pillar garnish clip is not damaged.

      Note


      • If there is any damage, replace the garnish clip with a new one.

      • When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.

    3. Engage the claw to direction indicated by the arrow (1).

    4. Engage the 3 guides to direction indicated by the arrow (2).

    5. Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish LH.

      Tech Tips

      Tape the needle-nosed pliers tip before use.

    6. A01J9PB

      Engage 2 clips to install the front pillar garnish LH.

  43. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01JDC6E01
      Text in Illustration
      *1 Alignment Mark (Yellow)

      Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  44. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01J99M

      Engage the 2 clips.

    2. Install the cowl side trim board LH with the clip.

  45. INSTALL FRONT DOOR SCUFF PLATE LH


    1. A01JB0N

      Engage the 10 claws to install the front door scuff plate LH.

  46. INSTALL CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  47. INSTALL CENTER PILLAR LOWER GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  48. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  49. INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

    Tech Tips

    Use the same procedure described for the LH side.

  50. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01J93LE01
      Text in Illustration
      *1 Alignment Mark (Blue)

      Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  51. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  52. INSTALL FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  53. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01JC1FE01
      Text in Illustration
      *1 Alignment Mark (White)

      Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  54. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  55. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  56. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  57. INSTALL REAR NO. 3 FLOOR BOARD


    1. A01JC33

      Engage the 2 guides to install the rear No. 3 floor board.

  58. INSTALL REAR DECK FLOOR BOX


    1. Install the rear deck floor box.

  59. INSTALL REAR NO. 2 FLOOR BOARD


    1. A01JCWRE01

      Engage the 3 guides <A>.

    2. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.