ROOF HEADLINING REASSEMBLY


  1. INSTALL NO. 1 ROOF WIRE


    1. Apply double-sided tape as shown in the illustration.

    2. Peel off the release paper from the double-sided tape.

    3. Attach the No. 1 roof wire along the double-sided tape so that the marking surface of the wire harness faces downward.

      A01J8GTE01
      Text in Illustration
      *1 Double-sided Tape *2 Marking

      Tech Tips

      If the entire length of the No. 1 roof wire does not fit, adjust the length by tucking in the hose at the area shown in the illustration.

      Double-sided Tape Size
      X
      1 mm (0.0394 in.)
      Y
      20 mm (0.787 in.)
      Z
      40 mm (1.57 in.)

    4. Align the pink marking tape <A>on the vehicle front side on the No. 1 roof wire with the vehicle front side tab on the roof headlining, and apply adhesive tape.

      Tech Tips

      Make sure that the No. 1 roof wire is not twisted and that the marking line (white) faces up.

    5. Turn the visor connector RH clockwise approximately 45° to install the connector to the roof headlining.

    6. Align the pink marking tape <B>on the No. 1 roof wire with the markings on the roof headlining, and apply adhesive tape.

    7. Engage each clamp.

    8. Align the pink marking tape <C>on the No. 1 roof wire with the markings on the roof headlining, and apply adhesive tape.

    9. Turn the visor connector LH clockwise approximately 45° to install the connector to the roof headlining.

    10. Attach the No. 1 roof wire, starting from the front of the vehicle, while aligning it with the double-sided tape.

      Note


      • Securely attach the No. 1 roof wire.

      • If any of the No. 1 roof wire is left loose, this will cause abnormal noise. Make sure to attach the No. 1 roof wire without leaving any loose.

      Tech Tips

      Secure the extra length of the No. 1 roof wire in the adjustment area.

    11. Apply adhesive tape by aligning it with the markings on the roof headlining.

      A01J9SCE01
      Text in Illustration
      *1 Adhesive Tape *2 Marking
      *3 Marking Line (White) *4 Adjustment Area
      *5 w/ EC Mirror *6 w/ Rain Sensor
      Double-sided Tape Size
      X
      20 mm (0.787 in.)
      Y
      100 mm (3.94 in.)

  2. INSTALL NO. 4 ANTENNA CORD SUB-ASSEMBLY

    Tech Tips

    Double-sided tape and tape are not available as supply parts. If the tape still has enough adhesion to secure the roof headlining and antenna cord, reuse it. If the roof headlining has been replaced with a new one, or if the tape and/or the double-sided tape is no longer sticky, apply new tape following the procedure below.

    If the double-sided tape cannot be reused:


    1. Peel off the release paper from one side of new double-sided tape and apply the new double-sided tape to the position indicated in the illustration. Be careful not to touch the adhesive surface.

      A01J9ACE04
      Text in Illustration
      *A w/o Sliding Roof *B w/ Sliding Roof
      *1 Double-sided Tape - -
      *a Front *b Double-sided Tape Size
      Double-sided Tape Size
      Area Dimension
      X 1.0 mm (0.0394 in.)
      Y 10.0 mm (0.394 in.)

      Note

      Be sure to apply the double-sided tape carefully so that the tape will not be misaligned or come off.

    2. Peel off the release paper from the double-sided tape. Be careful not to touch the adhesive surface.

    3. Align the vehicle front side marking (pink) on the No. 4 antenna cord sub-assembly with the vehicle front side tab on the roof headlining, and wrap the tape over the antenna cord to install it. (1)

      A01J9K6E03
      Text in Illustration
      *A w/o Sliding Roof *B w/ Sliding Roof
      *1 Tape *2 Extra Cord Storage Area
      *a Front *b Pink

      Tech Tips

      If the tape cannot be reused, packing tape can be used as a substitute.

    4. Temporarily install the front side of the No. 4 antenna cord sub-assembly with the adhesive tape. (2)

    5. Temporarily install the front side of the No. 4 antenna cord sub-assembly with the adhesive tape. (3)

    6. Temporarily install the No. 4 antenna cord sub-assembly by placing it on the double-sided tape from the front of the vehicle to the point just before the extra cord storage area.

    7. Align the vehicle rear marking (pink) on the No. 4 antenna cord sub-assembly with the tape attachment location (scribe line) of the roof headlining, and wrap the tape over the antenna cord to install it. (4)

      Tech Tips

      If the tape cannot be reused, packing tape can be used as a substitute.

    8. Temporarily install the rear side of the No. 4 antenna cord sub-assembly with the adhesive tape. (5)

    9. Temporarily install the No. 4 antenna cord sub-assembly by placing it on the double-sided tape from the rear of the vehicle to the point just before the extra cord storage area.

    10. A01J8GAE06
      Text in Illustration
      *1 Extra Cord Storage Area

      Using double-sided tape, place any excess No. 4 antenna cord sub-assembly in the extra cord storage area to finish installing the antenna cord.

      Tech Tips

      Attach 3 pieces of double-sided tape to the extra cord storage area as shown in the illustration.

  3. INSTALL NO. 3 ROOF SILENCER PAD (w/o Sliding Roof)


    1. Align the markings on the roof headlining assembly with the No. 3 roof silencer pad and install the set plate using hot-melt glue as shown in the illustration.

      A01JAX8E01
      Text in Illustration
      *1 Roof Silencer Pad Marking *2 Hot-melt Glue Marking

      Note

      Securely attach the No. 1 roof wire. Failure to do so may cause abnormal noise.

  4. INSTALL NO. 2 ROOF SILENCER PAD (w/o Sliding Roof)


    1. Align the markings on the roof headlining assembly with the No. 2 roof silencer pad and install the set plate using hot-melt glue as shown in the illustration.

      A01J93CE01
      Text in Illustration
      *1 Roof Silencer Pad Marking *2 Hot-melt Glue Marking

  5. INSTALL VANITY LIGHT ASSEMBLY


    1. Install the vanity light assembly Click here.

      Tech Tips

      Use the same procedure for the other vanity light.