ROOF HEADLINING REMOVAL


  1. PRECAUTION (w/ Navigation System for HDD)

    Note

    After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

  2. REMOVE REAR NO. 2 FLOOR BOARD


    1. A01JB5ZE01

      Disengage the 2 guides <A> as shown in the illustration.

    2. Disengage the 3 guides <B> and remove the rear No. 2 floor board.

  3. REMOVE REAR DECK FLOOR BOX


    1. Remove the rear deck floor box.

  4. REMOVE REAR NO. 3 FLOOR BOARD


    1. A01JC33

      Disengage the 2 guides and remove the rear No. 3 floor board.

  5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  6. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01JB0N

      Disengage the 10 claws and remove the front door scuff plate LH.

  7. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01J99M

      Remove the clip.

    2. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  8. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01JBR0

      Remove the front door opening trim weatherstrip LH.

  9. REMOVE FRONT PILLAR GARNISH LH


    1. A01JD69

      When removing the front pillar garnish LH, cover the shaded part in the illustration with a piece of cloth so that the interior parts will not be damaged.

    2. A01JCYQE01
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

      Tech Tips

      Make the front pillar garnish LH hang down from the front pillar garnish clip.

    3. A01JDC3E01

      Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish LH.

      Note


      • Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.

      • Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

      Tech Tips

      Tape the needle-nosed pliers tip before use.

      Text in Illustration
      *1 Protective Tape

    4. Disengage the 3 guides.

    5. A01JCPXE01

      Disengage the claw while pressing the shaded part in the illustration in the direction indicated by the arrow (1).

    6. Remove the front pillar garnish LH by pulling it in the direction indicated by the arrow (2) in the illustration.

    7. A01JBCIE01
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      Protect the curtain shield airbag assembly.


      1. Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  10. REMOVE REAR DOOR SCUFF PLATE LH


    1. A01JA7L

      Disengage the 7 claws and remove the rear door scuff plate LH.

  11. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01JAU4

      Remove the rear door opening trim weatherstrip LH.

  12. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)


    1. A01JB4X

      Disengage the 3 claws and remove the lap belt outer anchor cover.

  13. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A01J9GA

      Remove the bolt and disconnect the floor end of the front seat outer belt assembly.

  14. REMOVE CENTER PILLAR LOWER GARNISH LH


    1. A01JAI1

      Disengage the 2 claws and 2 clips, and remove the center pillar lower garnish LH.

  15. REMOVE CENTER PILLAR GARNISH LH


    1. A01JAOI

      Remove the screw.

    2. Using a clip remover, disengage the clip.

    3. Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar garnish LH and remove the center pillar garnish LH.

  16. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  17. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  18. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  19. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  20. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  21. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  22. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

    Tech Tips

    Use the same procedure described for the LH side.

  23. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  24. REMOVE CENTER PILLAR LOWER GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  25. REMOVE CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  26. REMOVE REAR SEAT CUSHION ASSEMBLY


    1. A01JC67E01
      Text in Illustration
      *1 100 mm (3.94 in.) or less
      *2 Hook
      *3 Guide

      Disengage the 2 front hooks of the seat cushion from the vehicle body as shown in the illustration.

      Note

      Follow the instructions below carefully as the cushion frame deforms easily.


      1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

      2. Repeat the above procedure for the other hook.

    2. Disengage the 2 guides of the seat cushion from the seatback.

    3. Remove the rear seat cushion assembly.

  27. REMOVE REAR SIDE SEATBACK ASSEMBLY LH


    1. A01J9D6

      Remove the bolt.

    2. A01J9I5

      Disengage the 2 guides and remove the rear side seatback assembly LH as shown in the illustration.

  28. REMOVE REAR SIDE SEATBACK ASSEMBLY RH


    1. A01JCTM

      Remove the bolt.

    2. A01JB67

      Disengage the 2 guides and remove the rear side seatback assembly RH as shown in the illustration.

  29. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY


    1. Remove the upper instrument panel assembly Click here.

  30. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Remove the tonneau cover assembly.

  31. REMOVE REAR NO. 4 FLOOR BOARD


    1. A01JB13

      Disengage the guide and remove the rear No. 4 floor board.

  32. REMOVE DECK FLOOR BOX LH


    1. A01J9G6

      Remove the clip.

    2. Disengage the 2 guides and remove the deck floor box LH.

  33. REMOVE REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY


    1. A01J8Q1

      Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board sub-assembly.

  34. REMOVE REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY


    1. A01JCFP

      Disengage the claw and 2 clips, and remove the rear No. 2 floor board sub-assembly.

  35. REMOVE REAR NO. 1 FLOOR BOARD


    1. A01JBVX

      Remove the bolt.

    2. Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board.

  36. REMOVE DECK TRIM SERVICE HOLE COVER


    1. A01JD05

      Disengage the 2 claws and 3 guides, and remove the deck trim service hole cover.

  37. REMOVE REAR DECK TRIM COVER


    1. A01JCDX

      Disengage the 4 claws and 4 guides, and remove the rear deck trim cover.

  38. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)


    1. A01JAKN

      Remove the 2 bolts.

    2. Disengage each guide and remove the 2 luggage hold belt striker assemblies.

  39. REMOVE TONNEAU COVER HOLDER CAP (for LH Side)


    1. A01JBMIE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the claw and remove the tonneau cover holder cap.

      Tech Tips

      Tape the screwdriver tip before use.

  40. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Remove the screw.

    2. Disengage the 7 claws and 2 clips.

    3. Disconnect the connector and remove the deck trim side panel assembly LH.

      A01J8UZ

  41. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH


    1. Disengage the 9 clips and remove the roof side inner garnish assembly LH.

      A01JCXV

  42. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure described for the LH side.

  43. REMOVE TONNEAU COVER HOLDER CAP (for RH Side)

    Tech Tips

    Use the same procedure described for the LH side.

  44. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH


    1. Remove the screw.

    2. Disengage the 7 claws and 2 clips, and remove the deck trim side panel assembly RH.

      A01JCY2

  45. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  46. REMOVE INNER REAR VIEW MIRROR COVER (w/ EC Mirror)


    1. A01JBP0

      Disengage the 2 claws and slide the inner rear view mirror cover as shown in the illustration.

    2. A01JBBW

      Disengage the 6 claws and remove the inner rear view mirror cover.

  47. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)


    1. A01JCC1

      Disconnect the rain sensor cover as shown in the illustration.

    2. Disengage the 2 claws and remove the rain sensor cover.

  48. REMOVE ROOF TOP MOULDING


    1. A01JB5T

      Using moulding remover B, disengage the 3 claws and 2 clips, and remove the roof top moulding.

  49. REMOVE MAP LIGHT ASSEMBLY (w/o Sliding Roof)


    1. A01J98M

      Disengage the 4 clips and 2 guides as shown in the illustration.

    2. Disconnect the connector and remove the map light assembly.

  50. REMOVE MAP LIGHT ASSEMBLY (w/ Sliding Roof)


    1. A01J8OA

      Disengage the 4 clips and 2 guides as shown in the illustration.

    2. Disconnect the connector and remove the map light assembly.

  51. REMOVE NO. 1 ROOM LIGHT ASSEMBLY


    1. A01JBAQE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver wrapped with protective tape, disengage the 4 claws and remove the No. 1 room light lens.

    2. A01JAPME01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver wrapped with protective tape, disengage the 2 claws and 2 guides, and remove the 2 No. 1 room light covers.

    3. A01JBVOE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver wrapped with protective tape, disengage the 4 claws and disconnect the No. 1 room light assembly as shown in the illustration.

    4. A01J8N2

      Using a screwdriver, disengage the 4 claws and disconnect the room light switch base from the No. 1 room light assembly.

  52. REMOVE FRONT ASSIST GRIP ASSEMBLY


    1. A01J8L8E01

      Using a clip remover, disengage the 4 claws.

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips


      • Gently pry on the assist grip covers as shown in the illustration to remove them.

      • Tape the clip remover tip before use.

    2. Pull off the 2 assist grip covers by hand.

    3. A01JAI9

      Disengage the 2 clips and remove the front assist grip assembly.

    4. Remove the 2 clips from the vehicle body.

      Tech Tips

      Use the same procedure for the other front assist grip.

  53. REMOVE REAR ASSIST GRIP ASSEMBLY


    1. A01JBS5E01

      Using a clip remover, disengage the 4 claws.

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips


      • Gently pry on the assist grip covers as shown in the illustration to remove them.

      • Tape the clip remover tip before use.

    2. Pull off the 2 assist grip covers by hand.

    3. A01J8LL

      Disengage the 2 clips and remove the rear assist grip assembly.

    4. Remove the 2 clips from the vehicle body.

      Tech Tips

      Use the same procedure for the other rear assist grip.

  54. REMOVE VISOR BRACKET COVER LH


    1. A01JAD9

      Using moulding remover B, disengage the 3 claws and remove the visor bracket cover LH.

  55. REMOVE VISOR ASSEMBLY LH


    1. A01J8GB

      Disengage the 2 clips and remove the visor assembly LH.

  56. REMOVE VISOR BRACKET COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  57. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  58. REMOVE VISOR HOLDER


    1. A01JBTKE01

      Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Disengage the 2 claws and remove the visor holder.

      Tech Tips

      Use the same procedure for the other visor holder.

  59. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)


    1. w/ Rain Sensor:


      1. Disengage the 2 clamps and disconnect the rain sensor connector.

    2. w/ EC Mirror:


      1. Disengage the 2 clamps and disconnect the inner rear view mirror connector.

    3. Disengage the 3 clamps and disconnect the connector from the front pillar RH.

    4. Disengage the clamp and disconnect the connector from the rear pillar RH.

    5. Disengage the 4 clamps from the front pillar LH.

    6. Disconnect the 2 No. 1 roof wire connectors from the connector holder.

    7. Remove the 5 clips.

      A01JBSNE01
      Text in Illustration
      *1 w/ EC Mirror *2 w/ Rain Sensor
    8. A01J9E4

      Remove the roof headlining assembly from the vehicle through the back door.

      Note

      Do not damage the roof headlining assembly or body interior.

  60. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)


    1. w/ Rain Sensor:


      1. Disengage the 2 clamps and disconnect the rain sensor connector.

    2. w/ EC Mirror:


      1. Disengage the 2 clamps and disconnect the inner rear view mirror connector.

    3. Disengage the 3 clamps and disconnect the connector from the front pillar RH.

    4. Disengage the clamp and disconnect the connector from the rear pillar RH.

    5. Disengage the 4 clamps from the front pillar LH.

    6. Disconnect the 2 No. 1 roof wire connectors from the connector holder.

    7. Remove the 3 clips.

      A01JATKE01
      Text in Illustration
      *1 w/ EC Mirror *2 w/ Rain Sensor

    8. Disengage the 6 fasteners.

      A01J9W9
    9. A01J9XR

      Remove the roof headlining assembly from the vehicle through the back door.

      Note

      Do not damage the roof headlining assembly or body interior.