UPPER INSTRUMENT PANEL REMOVAL


  1. PRECAUTION

    Click here

    Note

    w/ Navigation System for HDD:

    After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

  2. REMOVE REAR NO. 2 FLOOR BOARD


    1. A01JB5ZE01

      Disengage the 2 guides <A> as shown in the illustration.

    2. Disengage the 3 guides <B> and remove the rear No. 2 floor board.

  3. REMOVE REAR DECK FLOOR BOX


    1. Remove the rear deck floor box.

  4. REMOVE REAR NO. 3 FLOOR BOARD


    1. A01JC33

      Disengage the 2 guides and remove the rear No. 3 floor board.

  5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  6. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY


    1. A01J9ZGE01
      Text in Illustration
      *a Lift slightly

      Using a moulding remover, slightly lift the panel at the position shown in the illustration.

    2. Pull the integration control and panel assembly in the direction indicated by the arrow to disengage the 6 claws.

    3. Disconnect each connector and remove the integration control and panel assembly.

  7. REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. A01JA02

      Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 2 claws and 2 clips.

    2. A01JAMJ

      Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 5 claws and remove the lower center instrument cluster finish panel sub-assembly.

  8. REMOVE INSTRUMENT PANEL CUP HOLDER ASSEMBLY


    1. A01JAMI

      Remove the 4 screws <C> and instrument panel cup holder assembly from the lower center instrument cluster finish panel sub-assembly.

  9. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Disengage the 14 claws.

    2. Disconnect the connector and remove the instrument cluster finish panel garnish.

      A01J8FE

  10. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A01JD4M

      Disengage the 3 claws.

    2. Disconnect the connector and remove the upper instrument panel finish panel sub-assembly.

  11. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Radio Receiver)


    1. A01JADX

      Disengage the 4 claws and remove the center instrument cluster finish panel sub-assembly.

  12. REMOVE RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)


    1. A01JBMF

      Remove the 4 bolts <B> and radio tuner opening cover with bracket.

  13. REMOVE RADIO RECEIVER WITH BRACKET (w/o Navigation System)


    1. A01JD1M

      Remove the 4 bolts.

    2. A01J8MZ

      Disengage the 4 claws as shown in the illustration.

    3. Disconnect each connector and remove the radio receiver with bracket.

  14. REMOVE NAVIGATION RECEIVER WITH BRACKET (w/ Navigation System)


    1. A01JCMN

      Remove the 4 bolts.

    2. A01J9QE

      Disengage the 4 claws and remove the navigation receiver assembly with bracket as shown in the illustration.

    3. Disconnect each connector.

  15. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01JB0N

      Disengage the 10 claws and remove the front door scuff plate LH.

  16. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01J99M

      Remove the clip.

    2. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  17. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. A01JA5Y

      Remove the screw <C>.

    2. A01JCRX

      Disengage the 6 claws and clip as shown in the illustration.

    3. A01J9TK

      Disengage the claw and 2 guides and disconnect the hood lock control cable.

    4. Disconnect each connector and clamp, and remove the lower instrument panel finish panel assembly.

  18. REMOVE NO. 1 INSTRUMENT PANEL REGISTER


    1. A01JASI

      Pull the No. 1 instrument panel register in the direction indicated by the arrow to disengage the 2 claws.

    2. A01JAFV

      Pull the No. 1 instrument panel register in the direction indicated by the arrow to disengage the 2 claws and remove the No. 1 instrument panel register.

  19. REMOVE NO. 1 CENTER INSTRUMENT CLUSTER FINISH PANEL


    1. A01J9TA

      Disengage the 4 claws to remove the No. 1 center instrument cluster finish panel.

  20. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

  21. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


    1. A01JBQR

      Pull the instrument panel finish panel end LH in the direction indicated by the arrow to disengage the 4 claws.

    2. A01JBRH

      Disengage the guide as shown in the illustration.

    3. A01J8V9

      Disengage the guide and remove the instrument panel finish panel end LH as shown in the illustration.

  22. REMOVE NO. 1 SIDE DEFROSTER NOZZLE


    1. A01JCQ6E01
      Text in Illustration
      *a Lift slightly

      Using a moulding remover, slightly lift the panel at the position shown in the illustration.

    2. Pull the No. 1 side defroster nozzle in the direction indicated by the arrow to disengage the 3 claws and remove the No. 1 side defroster nozzle.

  23. REMOVE NO. 2 INSTRUMENT PANEL REGISTER


    1. A01JBR5

      Pull the No. 2 instrument panel register in the direction indicated by the arrow to disengage the claw and clip.

    2. A01JAS9

      Pull the No. 2 instrument panel register in the direction indicated by the arrow to disengage the 2 claws and remove the No. 2 instrument panel register.

  24. REMOVE GLOVE COMPARTMENT DOOR


    1. Open the glove compartment door assembly.

    2. A01JD7O

      Pull the glove compartment door in the direction indicated by the arrow to disengage the 7 claws.

    3. Pull the glove compartment door in the direction indicated by the arrow to remove the glove compartment door.

  25. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  26. REMOVE INSTRUMENT PANEL FINISH PANEL END RH


    1. A01JA4B

      Pull the instrument panel finish panel end RH in the direction indicated by the arrow to disengage the 4 claws.

    2. A01JA0U

      Disengage the guide as shown in the illustration.

    3. A01J8XA

      w/o Airbag Cut Off Switch:


      1. Disengage the guide and remove the instrument panel finish panel end RH as shown in the illustration.

    4. w/ Airbag Cut Off Switch:


      1. Disengage the guide.

      2. Disconnect the connector and remove the instrument panel finish panel end RH as shown in the illustration.

  27. REMOVE FRONT PILLAR GARNISH LH


    1. A01JD69

      When removing the front pillar garnish LH, cover the shaded part in the illustration with a piece of cloth so that the interior parts will not be damaged.

    2. A01JCYQE01
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

      Tech Tips

      Make the front pillar garnish LH hang down from the front pillar garnish clip.

    3. A01JDC3E01

      Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish LH.

      Note


      • Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.

      • Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

      Tech Tips

      Tape the needle-nosed pliers tip before use.

      Text in Illustration
      *1 Protective Tape

    4. Disengage the 3 guides.

    5. A01JCPXE01

      Disengage the claw while pressing the shaded part in the illustration in the direction indicated by the arrow (1).

    6. Remove the front pillar garnish LH by pulling it in the direction indicated by the arrow (2) in the illustration.

    7. A01JBCIE01
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      Protect the curtain shield airbag assembly.


      1. Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  28. REMOVE FRONT PILLAR GARNISH CORNER PIECE LH


    1. A01J8PV

      Disengage the 3 claws and front pillar garnish corner piece LH as shown in the illustration.

  29. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. A01JB4OE01

      Pull the No. 1 instrument panel speaker panel sub-assembly in the direction indicated by the arrow to disengage the 6 claws and 2 guides, and remove the No. 1 instrument panel speaker panel sub-assembly.

  30. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY


    1. A01J9Y7

      Remove the 2 bolts.

    2. Disconnect the connector and remove the front No. 2 speaker assembly.

      Note

      Do not touch the cone part of the speaker.

  31. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  32. REMOVE FRONT PILLAR GARNISH CORNER PIECE RH


    1. A01JCY9

      Disengage the 3 claws and front pillar garnish corner piece RH as shown in the illustration.

  33. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. A01JBK9E01

      Pull the No. 2 instrument panel speaker panel sub-assembly in the direction indicated by the arrow to disengage the 6 claws and 2 guides, and remove the No. 2 instrument panel speaker panel sub-assembly.

  34. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  35. REMOVE INSTRUMENT CLUSTER FINISH PANEL END


    1. A01J932E01

      Pull the instrument cluster finish panel end in the direction indicated by the arrow to disengage the 5 claws and 2 guides, and remove the instrument cluster finish panel end.

  36. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Remove the 2 screws <C>.

    2. Disengage the 7 claws.

    3. Disconnect the connector and remove the center instrument cluster finish panel garnish.

      A01JB9T

  37. DISCONNECT NO. 3 INSTRUMENT PANEL WIRE


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01J9IPE01
      Text in Illustration
      *1 Slider

      Slide the slider to release the lock, and then disconnect the connector.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  38. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY


    1. Disconnect each connector.

    2. Disengage the 2 clamps.

      A01JATT

    3. Remove the 2 bolts <B>.

    4. Remove the 2 passenger airbag bolts <A>.

      A01J97YE01
      Text in Illustration
      *1 Passenger Airbag Bolt <A> *2 Bolt <B>

    5. Pull the upper instrument panel assembly in the direction indicated by the arrow to disengage the 2 claws and 4 clips.

    6. Pull the upper instrument panel assembly in the direction indicated by the arrow to disengage the 5 claws and remove the upper instrument panel assembly.

      A01J9CXE01